1771-6.5.132, PLC-5 DeviceNet Scanner User Manual

More documents

Recommendations

Info

7-4 TroubleshootingNumericCodeDescriptionNumeric Display Code Summary91 Bus-off condition detected on commport. Module is detectingcommunication errors.92 No network power detected on commport.Take this actionCheck DeviceNet connections andphysical media integrity. Check systemfor failed slave devices or other possiblesources of network interference.Provide network power. Make sure thatmodule drop cable is providing networkpower to module comm port.95 Application FLASH update in progress. None. Do not disconnect the modulewhile application FLASH is in progress.You will lose any existing data in themodule’s memory.97 Module halted by user command. Check ladder program for cause of faultbits.98 Unrecoverable firmware failure. Service or replace your module.99 Unrecoverable hardware failure. Service or replace your module.Publication 1771-6.5.132 - June 2000
Appendix A1785-ENET Module Channel ConfigurationConfiguring theCommunications ChannelBefore you can communicate with the PLC-5 processor over anEthernet network, you must configure the 1785-ENET module’sEthernet communications channel and download the configuration tothe PLC-5 processor. The following example describes how to do thisusing RSLogix 5 software.1. Select Channel Configuration under the Controller folder in theProject window.The Edit Channel Properties window will open.1 Publication 1771-6.5.132 - June 2000
Page 1 and 2:
PLC-5 DeviceNetScanner Module1771-S
Page 3:
European Communities (EC)Directive
Page 6 and 7:
P-2 About This User ManualContentsT
Page 8 and 9:
P-4 About This User ManualCommon Te
Page 10 and 11:
P-6 About This User ManualTerminolo
Page 12 and 13:
P-8 About This User ManualPublicati
Page 14 and 15:
Table of ContentsiiConfiguring theD
Page 16 and 17:
Table of ContentsivPublication 1771
Page 18 and 19:
1-2 Before You BeginWhat Your 1771-
Page 20 and 21:
1-4 Before You BeginThe 1771-SDN sc
Page 22 and 23:
1-6 Before You BeginCommunicating w
Page 24 and 25:
1-8 Before You BeginWhat 1771-SDN M
Page 26 and 27:
1-10 Before You BeginThe configurat
Page 28 and 29:
1-12 Before You BeginPublication 17
Page 30 and 31:
2-2 Planning Your Configuration and
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
2-10 Planning Your Configuration an
Page 40 and 41:
3-2 Hardware SetupInstalling the PL
Page 42 and 43:
3-4 Hardware SetupTo go online to t
Page 44 and 45:
3-6 Hardware Setup3. Insert the int
Page 46 and 47:
3-8 Hardware SetupSetting the Chann
Page 48 and 49:
3-10 Hardware SetupConnecting the S
Page 50 and 51:
3-12 Hardware SetupInstalling theSe
Page 52 and 53:
3-14 Hardware SetupPublication 1771
Page 54 and 55:
4-2 Configuring the DeviceNet Netwo
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63: 4-10 Configuring the DeviceNet Netw
Page 72 and 73: 5-2 Communicating with DeviceNet fr
Page 80 and 81: 5-10 Communicating with DeviceNet f
Page 96 and 97: 6-2 Creating and Running the Exampl
Page 104 and 105: 6-10 Creating and Running the Examp
Page 110 and 111: 7-2 TroubleshootingNetwork Status I
Page 114 and 115: A-2 1785-ENET Module Channel Config
Page 116 and 117: B-2 Installing and Configuring the
Page 118 and 119: B-4 Installing and Configuring the
Page 120 and 121: C-2 Installing and Configuring the
Page 122 and 123: C-4 Installing and Configuring the
Page 124 and 125: D-2 Data Map ExampleExample Framewo
Page 126 and 127: D-4 Data Map ExampleIn 1-slot addre
Page 128 and 129: D-6 Data Map ExampleExample OutputM
Page 130 and 131: D-8 Data Map ExampleThe following i
Page 132 and 133: D-10 Data Map ExamplePublication 17
Page 134 and 135: 2 Indexsetting the I/O chassis back
Page 136: ( )Other CommentsPLEASE FOLD HERENO
Page 139: PLC-5 DeviceNet Scanner Module User
show all

1771-6.5.132, PLC-5 DeviceNet Scanner User Manual

Create successful ePaper yourself

Delete template?

Save as template?