1771-6.5.132, PLC-5 DeviceNet Scanner User Manual

More documents

Recommendations

Info

4-16 Configuring the DeviceNet Network4. Select the Output tab.Highlight the RediSTATION as shown above and click on theAutoMap button. The mapping of the RediSTATION will appear inthe lower panel.File N10,Word 1Note: The destination address isactually determined by the blocktransfer instruction in the ladderlogic. See chapter 6.After mapping theRediSTATION outputaddress will appearhere.In this example, the output to the RediSTATION appears in thePLC-5 processor in file N10, word 1, as the lower byte (bits 0-7).Recall from chapter 3 that the indicator light is output bit 0.Therefore, the address for the RediSTATION’s indicator light is:N10:1.05. Note the address assigned to this output in your system. Youwill enter this address in the example ladder logic program.Publication 1771-6.5.132 - June 2000
Configuring the DeviceNet Network 4-17Download the Configuration to the Scanner1. Click on the Scanlist tab and then on the Download to Scannerbutton.You will see this window:2. Select Channel A (default).Note: Both channels will download.3. Select All Records.4. Click on the Download button to download the configuration tothe 1771-SDN scanner module.5. Click on the OK button to complete the DeviceNet scannerconfiguration.6. Select the Save as option from the File menu, and save theDeviceNet configuration, using an appropriate name, e.g.,1771-SDN.dnt.7. Close the RSNetWorx for DeviceNet software.What’s Next?The next chapter describes how to configure the DeviceNet networkremotely from other networks: Ethernet, ControlNet, and DataHighway Plus.Publication 1771-6.5.132 - June 2000
Page 1 and 2:
PLC-5 DeviceNetScanner Module1771-S
Page 3:
European Communities (EC)Directive
Page 6 and 7:
P-2 About This User ManualContentsT
Page 8 and 9:
P-4 About This User ManualCommon Te
Page 10 and 11:
P-6 About This User ManualTerminolo
Page 12 and 13:
P-8 About This User ManualPublicati
Page 14 and 15:
Table of ContentsiiConfiguring theD
Page 16 and 17:
Table of ContentsivPublication 1771
Page 18 and 19: 1-2 Before You BeginWhat Your 1771-
Page 20 and 21: 1-4 Before You BeginThe 1771-SDN sc
Page 22 and 23: 1-6 Before You BeginCommunicating w
Page 24 and 25: 1-8 Before You BeginWhat 1771-SDN M
Page 26 and 27: 1-10 Before You BeginThe configurat
Page 28 and 29: 1-12 Before You BeginPublication 17
Page 30 and 31: 2-2 Planning Your Configuration and
Page 38 and 39: 2-10 Planning Your Configuration an
Page 40 and 41: 3-2 Hardware SetupInstalling the PL
Page 42 and 43: 3-4 Hardware SetupTo go online to t
Page 44 and 45: 3-6 Hardware Setup3. Insert the int
Page 46 and 47: 3-8 Hardware SetupSetting the Chann
Page 48 and 49: 3-10 Hardware SetupConnecting the S
Page 50 and 51: 3-12 Hardware SetupInstalling theSe
Page 52 and 53: 3-14 Hardware SetupPublication 1771
Page 54 and 55: 4-2 Configuring the DeviceNet Netwo
Page 62 and 63: 4-10 Configuring the DeviceNet Netw
Page 72 and 73: 5-2 Communicating with DeviceNet fr
Page 80 and 81: 5-10 Communicating with DeviceNet f
Page 96 and 97: 6-2 Creating and Running the Exampl
Page 104 and 105: 6-10 Creating and Running the Examp
Page 110 and 111: 7-2 TroubleshootingNetwork Status I
Page 112 and 113: 7-4 TroubleshootingNumericCodeDescr
Page 114 and 115: A-2 1785-ENET Module Channel Config
Page 116 and 117: B-2 Installing and Configuring the
Page 118 and 119:
B-4 Installing and Configuring the
Page 120 and 121:
C-2 Installing and Configuring the
Page 122 and 123:
C-4 Installing and Configuring the
Page 124 and 125:
D-2 Data Map ExampleExample Framewo
Page 126 and 127:
D-4 Data Map ExampleIn 1-slot addre
Page 128 and 129:
D-6 Data Map ExampleExample OutputM
Page 130 and 131:
D-8 Data Map ExampleThe following i
Page 132 and 133:
D-10 Data Map ExamplePublication 17
Page 134 and 135:
2 Indexsetting the I/O chassis back
Page 136:
( )Other CommentsPLEASE FOLD HERENO
Page 139:
PLC-5 DeviceNet Scanner Module User
show all

1771-6.5.132, PLC-5 DeviceNet Scanner User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?