1771-6.5.132, PLC-5 DeviceNet Scanner User Manual

More documents

Recommendations

Info

3-12 Hardware SetupInstalling theSeries 9000 PhotoeyeConnect the photoeye to the network and configure the photoeye asfollows:• Node Address: 9• Operating Mode: Light Operate (default)• Baud Rate: 500 kbTop View of Series 9000 PhotoeyeProgrammingPushbuttonSensitivityAdjustmentYellow - OutputGreen - MarginRed/Green - StatusMoreFor detailed directions, see the instructions that came with yourphotoeye.Publication 1771-6.5.132 - June 2000
Hardware Setup 3-13How Your ExampleSystem Will LookWhen you have finished installing all the devices, your examplesystem should look similar to the one shown below:PC running Windows NTor Windows 95/98,containing RSNetWorx forDeviceNet softwarePC SerialPort1770-KFDCommunicationModuleNode 62Series 9000PhotoelectricSensor24VNode 91492-DN3TWQuad TapNode 0Node 7PLC-5 Processor with 1771-SDNmodule in 1771 I/O chassisRediSTATIONOperator InterfaceIMPORTANTMake sure each end of your DeviceNet trunk cableis properly terminated with a resistor. Refer to theDeviceNet Cable Planning and Installation Manual,publication DN-6.7.2 for detailed information.What’s Next?The next step is to configure the 1771-SDN module and perform I/Odata mapping using RSNetWorx for DeviceNet software.Publication 1771-6.5.132 - June 2000
Page 1 and 2: PLC-5 DeviceNetScanner Module1771-S
Page 3: European Communities (EC)Directive
Page 6 and 7: P-2 About This User ManualContentsT
Page 8 and 9: P-4 About This User ManualCommon Te
Page 10 and 11: P-6 About This User ManualTerminolo
Page 12 and 13: P-8 About This User ManualPublicati
Page 14 and 15: Table of ContentsiiConfiguring theD
Page 16 and 17: Table of ContentsivPublication 1771
Page 18 and 19: 1-2 Before You BeginWhat Your 1771-
Page 20 and 21: 1-4 Before You BeginThe 1771-SDN sc
Page 22 and 23: 1-6 Before You BeginCommunicating w
Page 24 and 25: 1-8 Before You BeginWhat 1771-SDN M
Page 26 and 27: 1-10 Before You BeginThe configurat
Page 28 and 29: 1-12 Before You BeginPublication 17
Page 30 and 31: 2-2 Planning Your Configuration and
Page 38 and 39: 2-10 Planning Your Configuration an
Page 40 and 41: 3-2 Hardware SetupInstalling the PL
Page 42 and 43: 3-4 Hardware SetupTo go online to t
Page 44 and 45: 3-6 Hardware Setup3. Insert the int
Page 46 and 47: 3-8 Hardware SetupSetting the Chann
Page 48 and 49: 3-10 Hardware SetupConnecting the S
Page 52 and 53: 3-14 Hardware SetupPublication 1771
Page 54 and 55: 4-2 Configuring the DeviceNet Netwo
Page 62 and 63: 4-10 Configuring the DeviceNet Netw
Page 72 and 73: 5-2 Communicating with DeviceNet fr
Page 80 and 81: 5-10 Communicating with DeviceNet f
Page 96 and 97: 6-2 Creating and Running the Exampl
Page 98 and 99: 6-4 Creating and Running the Exampl
Page 100 and 101:
6-6 Creating and Running the Exampl
Page 102 and 103:
6-8 Creating and Running the Exampl
Page 104 and 105:
6-10 Creating and Running the Examp
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
7-2 TroubleshootingNetwork Status I
Page 112 and 113:
7-4 TroubleshootingNumericCodeDescr
Page 114 and 115:
A-2 1785-ENET Module Channel Config
Page 116 and 117:
B-2 Installing and Configuring the
Page 118 and 119:
B-4 Installing and Configuring the
Page 120 and 121:
C-2 Installing and Configuring the
Page 122 and 123:
C-4 Installing and Configuring the
Page 124 and 125:
D-2 Data Map ExampleExample Framewo
Page 126 and 127:
D-4 Data Map ExampleIn 1-slot addre
Page 128 and 129:
D-6 Data Map ExampleExample OutputM
Page 130 and 131:
D-8 Data Map ExampleThe following i
Page 132 and 133:
D-10 Data Map ExamplePublication 17
Page 134 and 135:
2 Indexsetting the I/O chassis back
Page 136:
( )Other CommentsPLEASE FOLD HERENO
Page 139:
PLC-5 DeviceNet Scanner Module User
show all

1771-6.5.132, PLC-5 DeviceNet Scanner User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?