1771-6.5.132, PLC-5 DeviceNet Scanner User Manual

More documents

Recommendations

Info

Important User InformationBecause of the variety of uses for the products described in thispublication, those responsible for the application and use of this controlequipment must satisfy themselves that all necessary steps have beentaken to assure that each application and use meets all performance andsafety requirements, including any applicable laws, regulations, codes andstandards.The illustrations, charts, sample programs and layout examples shown inthis guide are intended solely for purposes of example. Since there aremany variables and requirements associated with any particularinstallation, Allen-Bradley does not assume responsibility or liability (toinclude intellectual property liability) for actual use based upon theexamples shown in this publication.Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application,Installation and Maintenance of Solid-State Control (available from yourlocal Allen-Bradley office), describes some important differences betweensolid-state equipment and electromechanical devices that should be takeninto consideration when applying products such as those described in thispublication.Reproduction of the contents of this copyrighted publication, in whole orpart, without written permission of Rockwell Automation, is prohibited.Throughout this manual we use notes to make you aware of safetyconsiderations:ATTENTION!Identifies information about practices orcircumstances that can lead to personal injury ordeath, property damage or economic lossAttention statements help you to:• identify a hazard• avoid a hazard• recognize the consequencesIMPORTANTIdentifies information that is critical for successfulapplication and understanding of the product.Allen-Bradley, Data Highway Plus, and PLC-5 are trademarks of Rockwell Automation.ControlNet is a trademark of ControlNet International, Ltd.DeviceNet is a trademark of Open DeviceNet Vendor Association (ODVA), Inc.Ethernet is a trademark of Digital Equipment Corporation, Intel, and Xerox Corporation.RSLinx, RSLogix 5, and RSNetWorx are trademarks of Rockwell Software.Windows 95/98 and Windows NT are trademarks of Microsoft Corporation.
European Communities (EC)Directive ComplianceIf this product has the CE mark it is approved for installation withinthe European Union and EEA regions. It has been designed and testedto meet the following directives.EMC DirectiveThis product is tested to meet the Council Directive 89/336/ECElectromagnetic Compatibility (EMC) by applying the followingstandards, in whole or in part, documented in a technical constructionfile:• EN 50081-2 EMC — Generic Emission Standard, Part 2 —Industrial Environment• EN 50082-2 EMC — Generic Immunity Standard, Part 2 —Industrial EnvironmentThis product is intended for use in an industrial environment.Low Voltage DirectiveThis product is tested to meet Council Directive 73/23/EEC LowVoltage, by applying the safety requirements of EN 61131-2Programmable Controllers, Part 2 - Equipment Requirements andTests. For specific information required by EN 61131-2, see theappropriate sections in this publication, as well as the Allen-Bradleypublication Industrial Automation Wiring and Grounding GuidelinesFor Noise Immunity, publication 1770-4.1.This equipment is classified as open equipment and must be mountedin an enclosure during operation to provide safety protection.
Page 1: PLC-5 DeviceNetScanner Module1771-S
Page 6 and 7: P-2 About This User ManualContentsT
Page 8 and 9: P-4 About This User ManualCommon Te
Page 10 and 11: P-6 About This User ManualTerminolo
Page 12 and 13: P-8 About This User ManualPublicati
Page 14 and 15: Table of ContentsiiConfiguring theD
Page 16 and 17: Table of ContentsivPublication 1771
Page 18 and 19: 1-2 Before You BeginWhat Your 1771-
Page 20 and 21: 1-4 Before You BeginThe 1771-SDN sc
Page 22 and 23: 1-6 Before You BeginCommunicating w
Page 24 and 25: 1-8 Before You BeginWhat 1771-SDN M
Page 26 and 27: 1-10 Before You BeginThe configurat
Page 28 and 29: 1-12 Before You BeginPublication 17
Page 30 and 31: 2-2 Planning Your Configuration and
Page 38 and 39: 2-10 Planning Your Configuration an
Page 40 and 41: 3-2 Hardware SetupInstalling the PL
Page 42 and 43: 3-4 Hardware SetupTo go online to t
Page 44 and 45: 3-6 Hardware Setup3. Insert the int
Page 46 and 47: 3-8 Hardware SetupSetting the Chann
Page 48 and 49: 3-10 Hardware SetupConnecting the S
Page 50 and 51: 3-12 Hardware SetupInstalling theSe
Page 52 and 53:
3-14 Hardware SetupPublication 1771
Page 54 and 55:
4-2 Configuring the DeviceNet Netwo
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
4-10 Configuring the DeviceNet Netw
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
5-2 Communicating with DeviceNet fr
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
5-10 Communicating with DeviceNet f
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
6-2 Creating and Running the Exampl
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
6-10 Creating and Running the Examp
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
7-2 TroubleshootingNetwork Status I
Page 112 and 113:
7-4 TroubleshootingNumericCodeDescr
Page 114 and 115:
A-2 1785-ENET Module Channel Config
Page 116 and 117:
B-2 Installing and Configuring the
Page 118 and 119:
B-4 Installing and Configuring the
Page 120 and 121:
C-2 Installing and Configuring the
Page 122 and 123:
C-4 Installing and Configuring the
Page 124 and 125:
D-2 Data Map ExampleExample Framewo
Page 126 and 127:
D-4 Data Map ExampleIn 1-slot addre
Page 128 and 129:
D-6 Data Map ExampleExample OutputM
Page 130 and 131:
D-8 Data Map ExampleThe following i
Page 132 and 133:
D-10 Data Map ExamplePublication 17
Page 134 and 135:
2 Indexsetting the I/O chassis back
Page 136:
( )Other CommentsPLEASE FOLD HERENO
Page 139:
PLC-5 DeviceNet Scanner Module User
show all

1771-6.5.132, PLC-5 DeviceNet Scanner User Manual

Create successful ePaper yourself

Delete template?

Save as template?