R 1200 CL

More documents

Recommendations

Info

$(Full p\340gina web.qxd)$

R 1200 CL Alarm System Programming Information Encoding Replacement RF Remote Controls Note:To encode RF Remote Controls you will need the 5 digit “personal pin code” for the alarm system.The code is entered into the system by synchronizing the switching of the ignition key when the appropriate LED flash corresponds with each digit of the code. A maximum of four RF remote controls can be encoded on the system. Activating the encoding function 1. Use a jumper to connect the programming plug to battery ground. 2.Turn the ignition switch to ON, after a brief pause switch to OFF. 3. Wait for the first digit code to flash ON and then OFF. Once OFF, switch the key back ON. 4. Pause for approximately 5 seconds and switch ignition off. Repeat this process for each of the remaining digits in the code. 5. On completion of the last digit, three beeps will be heard indicating encoding function is active. NOTE: If the beeps are not heard, you must repeat steps 2 - 5 ensuring the key is switched ON after the last flash of the coded number switches OFF. Personal Pin Code Card Signal the five digit code to the system by switching the ignition key ON when the total number of flashes occur for each number in the code. Example: Code input for 11559 124 R 1200 CL Introduction
R 1200 CL Alarm System Programming Information Encoding the remote controls Note: All RF remote controls must be encoded at the same time for them to be functional • Press and hold buttons A and B on the remote control simultaneously. • LED on remote will flash rapidly, keep buttons A and B pressed down. • After approximately 10 seconds, the remote LED will stop flashing, release buttons A and B. • Once released, the RF Remote LED will light up steadily. • Press either button A or B. • A beep will indicate that the encoding of the remote control has been successful. • Repeat the procedure for all other remote controls. R 1200 CL Introduction RF Remote LED Encoding RF Remote Control 125
Page 1 and 2:
R 1200 CL • Technical Features in
Page 3 and 4:
R 1200 CL Table of Contents Subject
Page 5 and 6:
R 1200 CL Introduction Overview. As
Page 7 and 8:
R 1200 CL Engine The two piece ligh
Page 9 and 10:
R 1200 CL Clutch Centrifugal mass i
Page 11 and 12:
R 1200 CL Gear Box The engaging and
Page 13 and 14:
R 1200 CL Digital Motor Electronics
Page 15 and 16:
R 1200 CL Digital Motor Electronics
Page 17 and 18:
R 1200 CL Chassis and Wheels To pre
Page 19 and 20:
R 1200 CL Chassis and Wheels The Mo
Page 21 and 22:
R 1200 CL Chassis and Wheels The ne
Page 23 and 24:
R 1200 CL Brake Components and Inte
Page 25 and 26:
R 1200 CL Brake Components and Inte
Page 27 and 28:
R 1200 CL Bodywork There are two wi
Page 29 and 30:
R 1200 CL Bodywork Technical Featur
Page 31 and 32:
R 1200 CL Headlights Lever Position
Page 33 and 34:
R 1200 CL Electrical Components 3 1
Page 35 and 36:
R 1200 CL 1. With the ignition in t
Page 37 and 38:
R 1200 CL Cruise Control Technical
Page 39 and 40:
R 1200 CL Sound and Communication S
Page 41 and 42:
R 1200 CL Technical Data Clutch: Cl
Page 43 and 44:
R 1200 CL Technical Data Dimensions
Page 45 and 46:
R 1200 CL PDI Procedures - Uncratin
Page 47 and 48:
R 1200 CL PDI Procedures - Uncratin
Page 49 and 50:
R 1200 CL PDI Procedures - Set Up C
Page 51 and 52:
R 1200 CL PDI Procedures - Set Up
Page 53 and 54:
R 1200 CL PDI Procedures - Accessin
Page 55 and 56: R 1200 CL PDI Procedures - Removing
Page 57 and 58: R 1200 CL PDI Procedures - Checking
Page 59 and 60: R 1200 CL PDI Procedures - Check En
Page 61 and 62: R 1200 CL PDI Procedures - Check He
Page 63 and 64: R 1200 CL Retail Delivery Handover
Page 65 and 66: R 1200 CL Retail Delivery Check Lis
Page 67 and 68: R 1200 CL US Market Service Lubrica
Page 69 and 70: R 1200 CL Maintenance Schedule Chec
Page 71 and 72: R 1200 CL BMW Inspection I Procedur
Page 79 and 80: R 1200 CL Service & Maintenance Dat
Page 81 and 82: R 1200 CL New Special Tools - Part
Page 83 and 84: F 650 CS Additional Information New
Page 85 and 86: R 1200 CL Wiring & Terminal Designa
Page 87 and 88: R 1200 CL Power Distribution and Gr
Page 89 and 90: R 1200 CL Motronic M2.4 without Ant
Page 91 and 92: R 1200 CL Motronic M2.4 with or wit
Page 93 and 94: R 1200 CL Cruise Control 99/100 R 1
Page 95 and 96: R 1200 CL Instrumentation (Part 2 o
Page 97 and 98: R 1200 CL Horn, Hazard Flashers & T
Page 99 and 100: R 1200 CL Heated Grips/Seat & Diagn
Page 101 and 102: R 1200 CL Fuse Designations and Ele
Page 103 and 104: R 1200 CL Electrical Components Vie
Page 105: R 1200 CL Alarm System Programming
show all

R 1200 CL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?