Legacy Data System Reference - Comtech EF Data

More documents

Recommendations

Info

<strong>Legacy</strong> <strong>Data</strong> 12.8.4 Poll delay (ms) Console SNMP Text-based Config Poll delay (ms) ifwanPollDelay-ms [ifwan#] PollDelay-ms The wait time, in milliseconds, before transmitting a poll. This parameter is always required for a primary SDLC port connected to a controller. It may also be used on a secondary SDLC port that is set to full duplex mode in host-to-host applications. Values: 0 - 1000 Default: 10 12-18 Memotec Inc.
12.9 COP Port 12.9.1 Synchronization character SE/PORT Configuration Parameters For COP protocol only. The hexadecimal value of the synchronization character. The Synchronization Character must be different from the Idle that has been defined for the COP port, or synchronization cannot be achieved. For example, if the Synchronization Character is 0000 then the Idle parameter cannot be set to SPACE. If the Synchronization Character is set to FFFF, then the Idle must be set to SPACE to get the port working. The following table summarizes these requirements: 12.9.2 Number of desynch. character s For COP protocol only. This parameter defines the number of contiguous desynchronization characters that must be received before the NetPerformer drops synchronization and closes the frame. 12.9.3 Desynchronization character Console SNMP Text-based Config Synchronization character Idle Synchronization Character SPACE Any value different from 0000 MARK Any value different from FFFF Values: 0000 - FFFF Default: 1616 ifwanSync [ifwan#] Sync Console SNMP Text-based Config Number of desynch. characters Values: 1 - 100 Default: 3 ifwanDropSyncCoun-ter ifwan#] DropSyncCounter Console SNMP Text-based Config Desynchronization character ifwanDropSyncCharacter ifwan#] Drop- SyncCharacter For COP protocol only. The hexadecimal value of the desynchronization character. This parameter defines the Memotec Inc. 12-19
Page 1 and 2:
Legacy Data NetPerformer ® System
Page 3 and 4:
Contents Chapter 1: HDLC Protocol .
Page 5 and 6:
8.1.2 Transmission:. . . . . . . .
Page 7 and 8:
12.10.1 X25 frame relay encapsulati
Page 9 and 10:
15.1.9 NODE. . . . . . . . . . . .
Page 11 and 12:
HDLC Protocol 1 Memotec Inc. 1-1
Page 13 and 14:
1.2 NetPerformer Support of HDLC HD
Page 15 and 16:
HDLC Protocol PORT 1> Protocol (def
Page 17 and 18:
HDLCOFR Protocol 2 Memotec Inc. 2-1
Page 19 and 20:
PASSTHRU Protocol 3 Memotec Inc. 3-
Page 21 and 22:
3.3 Configuring a PASSTHRU Connecti
Page 23 and 24:
PASSTHRUOFR Protocol 4 Memotec Inc.
Page 25 and 26:
4.1.1 Number of Digital PASSTHRUOFR
Page 27 and 28:
PASSTHRUOFR Protocol 4.3 Configurin
Page 29 and 30:
SE/SLOT/#/ CHANNEL/ PASSTHRUOF R ex
Page 31 and 32:
Asynchronous Protocols 5 Memotec In
Page 33 and 34:
Asynchronous Protocols 5.4 Configur
Page 35 and 36:
SE/PORT/#/R- ASYNC example SE/SLOT/
Page 37 and 38:
SNA/SDLC Support 6 Memotec Inc. 6-1
Page 39 and 40:
SNA/SDLC Support • SNA/SDLC port
Page 41 and 42:
SNA/SDLC Support representing the s
Page 43 and 44:
SNA/SDLC Support routes SNA to the
Page 45 and 46:
SNA/SDLC Support PHONE/ PORT/PU/PPP
Page 47 and 48:
6.3 Configuring a PU SNA/SDLC Suppo
Page 49 and 50:
PU 1> LLC frame size (def:512) ? PU
Page 51 and 52:
6.3.6 Configuring a Non-SDLC PU Con
Page 53 and 54: BSC Protocol 7 Memotec Inc. 7-1
Page 55 and 56: BSC Protocol At the remote end, the
Page 57 and 58: COP Protocol 8 Memotec Inc. 8-1
Page 59 and 60: 8.2 Configuring a COP Connection CO
Page 61 and 62: X.25 Protocol 9 Memotec Inc. 9-1
Page 63 and 64: • Idle:FLAG • Frame Delay:0.0 9
Page 65 and 66: 9.3 X.25 Application Example X.25 H
Page 67 and 68: IPX Connections 10 Memotec Inc. 10-
Page 69 and 70: 10.2 Configuring an IPX Connection
Page 71 and 72: IPX Connections The six IP submenus
Page 73 and 74: 10.3.2 IPX SAP Routing Table DR/IPX
Page 75 and 76: Monitoring Data Port Functions 11 M
Page 77 and 78: 11.2 Display Counters (DC) DC/PORT
Page 79 and 80: 11.3 Display States (DS) DS/PORT ex
Page 81 and 82: 11.4 Display Port States (DPORT) DP
Page 83 and 84: DE/PU example Monitoring Data Port
Page 85 and 86: 11.7 Display Parameters (DP) DP/SLO
Page 87 and 88: SE/PORT Configuration Parameters 12
Page 89 and 90: 12.1.2 Port speed (bps) 12.1.3 Cloc
Page 91 and 92: 12.2 HDLC and PASSTHRU Ports 12.2.1
Page 93 and 94: 12.2.3 Modem control signal SE/PORT
Page 95 and 96: 12.2.4 Frame delay (ms) 12.2.5 CRC
Page 97 and 98: 12.2.9 Remote port number 12.2.10 S
Page 99 and 100: 12.3 HDLCOFR Port 12.3.1 Tx/Rx mode
Page 101 and 102: 12.6 T-ASYNC Port 12.6.1 Format SE/
Page 103: 12.8 P-SDLC Port 12.8.1 SDLC duplex
Page 107 and 108: 12.10 X25 Port 12.10.1 X25 frame re
Page 109 and 110: SE/PU Configuration Parameters 13 M
Page 111 and 112: 13.1.3 Controller active SE/PU Conf
Page 113 and 114: 13.1.8 SDLC secondary address SE/PU
Page 115 and 116: 13.2 SDLC-LINKS Mode 13.2.1 SDLC po
Page 117 and 118: 13.3 SDLC-LLC Mode 13.3.1 LLC lan p
Page 119 and 120: 13.3.6 LLC maximum successive retri
Page 121 and 122: SE/PU Configuration Parameters The
Page 123 and 124: 13.4 SDLC-BAN Mode 13.4.1 BAN desti
Page 125 and 126: 13.4.6 BAN/BNN transmission window
Page 127 and 128: 13.5 SDLC-BNN Mode 13.5.1 BNN PVC n
Page 129 and 130: SE/IPX Configuration Parameters 14
Page 131 and 132: 14.1.3 IPX network number 14.1.4 IP
Page 133 and 134: Net1 Ethernet RT1 PVCR or FW SE/IPX
Page 135 and 136: 14.3 SE/IPX/FILTER Parameters 14.3.
Page 137 and 138: IPX Display Command Statistics 15 M
Page 139 and 140: 15.1.7 DR/IPX/SAP 15.1.8 NET NUM 15
Page 141 and 142: 15.1.14 AGE Console SNMP AGE (use p
Page 143 and 144: Index A Activation status of PU 13-
Page 145 and 146: O Operating mode of PU 13-2 P Param
Page 147 and 148: PU connection 13-4 SERVICE NAME dis
show all

Legacy Data System Reference - Comtech EF Data

Create successful ePaper yourself

Delete template?

Save as template?