ERECTION AND SAFETY MANUAL - Rigid Global Buildings

Recommendations

Info

5.21 SKYLIGHT INSTALLATION Page 7.1-72 Revision: 2 August 2011 ERECTION AND SAFETY MANUAL Skylight panels are installed using the same procedures as a steel panel. Care should be taken when installing fasteners in the skylights to avoid cracking the material. Pre-drill W diameter fastener clearance holes in the overlapping sidelap and endlap. UP HILL NOTE: Panel installation sequence - 1, 2, 3, 4 and 5 DOWN HILL 1/8” FASTENER HOLE PRE-DRILL 1/4” CLEARANCE HOLE SIDE LAP DETAIL NOTE: Do not under any circumstances step or walk on surface of skylight. If foot traffi c is necessary over skylight, use walk boards that are properly supported by building purlins. Placing of “DANGER DO NOT WALK” markings on every skylight must be done without fail. Safety fi rst! Technical information contained herein is subject to change without notice.
ERECTION AND SAFETY MANUAL 5.22 TAPE SEALANT APPLICATION AT RIDGE FLASHING Apply panel sidelap tape sealant as shown for building with ridge fl ashing and outside closures. The mastic is placed along the inside edge of the major rib from the ridge purlin web line to the upper end of the panel. TAPE SEALANT OUTSIDE CLOSURE PURLIN ROOF PANEL SEALANT RIDGE FLASHING DETAILS PEAK PURLIN OUTSIDE CLOSURE TAPE SEALANT ROOF PANEL RIDGE FLASHING FASTENER Technical information contained herein is subject to change without notice. Page 7.1-73 Revision: 2 April 2011
Page 1:
ERECTION AND SAFETY MANUAL
Page 4 and 5:
Page 7.1-ii Revision: 1 April 2011
Page 6 and 7:
INTRODUCTION Page 7.1-2 Revision: 2
Page 8 and 9:
1.2 FOUNDATION CHECKING PROCEDURE P
Page 10 and 11:
2.1 ACCESS TO SITE Page 7.1-6 Revis
Page 12 and 13:
Page 7.1-8 Revision: 2 August 2011
Page 14 and 15:
3.1 STRUCTURAL Page 7.1-10 Revision
Page 16 and 17:
Page 18 and 19:
3.4 CABLE TENSION AND HOOK HEIGHT P
Page 20 and 21:
Page 22 and 23:
RECOMMENDED MINIMUM BASIC TOOL PACK
Page 24 and 25:
Page 26 and 27: 4.4 RAISING RIGID FRAMES Page 7.1-2
Page 28 and 29: ERECTION AND SAFETY MANUAL A second
Page 30 and 31: Page 7.1-26 Revision: 2 August 2011
Page 40 and 41: ERECTION AND SAFETY MANUAL To plumb
Page 42 and 43: 4.8 ERECTING THE REMAINING FRAMES P
Page 44 and 45: 4.9 WIND BRACING INSTALLATION Page
Page 48 and 49: 5.2 “R” PANEL Page 7.1-44 Revis
Page 50 and 51: 5.4 “AW” PANEL Page 7.1-46 Revi
Page 52 and 53: 5.6 FASTENER INSTALLATION Page 7.1-
Page 54 and 55: ERECTION AND SAFETY MANUAL The temp
Page 56 and 57: 5.8 WALL INSULATION Page 7.1-52 Rev
Page 58 and 59: 5.9 ROOF INSULATION Page 7.1-54 Rev
Page 60 and 61: ERECTION AND SAFETY MANUAL A four f
Page 62 and 63: ERECTION AND SAFETY MANUAL Backlapp
Page 70 and 71: 5.15 SEALING THE EAVE Page 7.1-66 R
Page 72 and 73: 5.17 PANEL ENDLAPS Page 7.1-68 Revi
Page 74 and 75: 5.19 INSTALLATION OF ROOF PANELS Pa
Page 82: 6.3 FLASHING CAULK AND LAP DETAILS
show all

ERECTION AND SAFETY MANUAL - Rigid Global Buildings

Create successful ePaper yourself

Delete template?

Save as template?