ERECTION AND SAFETY MANUAL - Rigid Global Buildings

Recommendations

Info

Page 7.1-76 Revision: 2 August 2011 ERECTION AND SAFETY MANUAL Lift the gutter assembly into position under the edge of the roof panels and temporarily clamp the back fl ange of panel to the gutter. Position the back face of the gutter assembly fl ush against the panel cap trim and position its ends fl ush with the exterior face of the rake wall. Fasten the gutter’s back fl ange to the underside of the roof panel with the lap fasteners, as shown. Check that the lap fasteners are securely engaged into the gutter’s back fl ange. Align the outer edge of the gutter straight and level. Use a string line to assure that the gutter is straight Install the gutter straps and fasten to the roof panel with stitch screw and fasten the gutter’s outer fl ange to the end of the gutter strap with a pop rivet, as shown. NOTE: Workers should always use gloves when handling fl ashing and follow all OSHA safety recommendations. Never install any material if its quality or appropriateness is in question! RIGID manufactures various trim profi les - the examples shown may or may not match building in question. Safety fi rst! Technical information contained herein is subject to change without notice.
ERECTION AND SAFETY MANUAL 6.2 RAKE TRIM & PEAK BOX INSTALLATION Apply caulking to rake trim as shown below prior to fi nial installation. Rake Trim and/or Peak Box should lap over rake trim a minimum of 2 inches. Attach to wall panel with #10 fasteners using an outside closure to seal box at the wall. Attach box to roof with #14 roof fasteners and stitch to trim with blind rivets as shown. Seal the connection at the roof panel with 1/8” tape sealant (drill 1/4” diameter clearance holes through plastic for fasteners to prevent cracking). Splice rake trim with pop rivets at peak box and seal all rake trim laps with sealant to assure a weather-tight seal. TAPE SEALANT CAULK POP RIVETS RAKE TRIM PEAK BOX FIELD NOTCH TO FIT RIDGE Technical information contained herein is subject to change without notice. Page 7.1-77 Revision: 2 April 2011
Page 1:
ERECTION AND SAFETY MANUAL
Page 4 and 5:
Page 7.1-ii Revision: 1 April 2011
Page 6 and 7:
INTRODUCTION Page 7.1-2 Revision: 2
Page 8 and 9:
1.2 FOUNDATION CHECKING PROCEDURE P
Page 10 and 11:
2.1 ACCESS TO SITE Page 7.1-6 Revis
Page 12 and 13:
Page 7.1-8 Revision: 2 August 2011
Page 14 and 15:
3.1 STRUCTURAL Page 7.1-10 Revision
Page 16 and 17:
Page 18 and 19:
3.4 CABLE TENSION AND HOOK HEIGHT P
Page 20 and 21:
Page 22 and 23:
RECOMMENDED MINIMUM BASIC TOOL PACK
Page 24 and 25:
Page 26 and 27:
4.4 RAISING RIGID FRAMES Page 7.1-2
Page 28 and 29:
ERECTION AND SAFETY MANUAL A second
Page 30 and 31: Page 7.1-26 Revision: 2 August 2011
Page 40 and 41: ERECTION AND SAFETY MANUAL To plumb
Page 42 and 43: 4.8 ERECTING THE REMAINING FRAMES P
Page 44 and 45: 4.9 WIND BRACING INSTALLATION Page
Page 48 and 49: 5.2 “R” PANEL Page 7.1-44 Revis
Page 50 and 51: 5.4 “AW” PANEL Page 7.1-46 Revi
Page 52 and 53: 5.6 FASTENER INSTALLATION Page 7.1-
Page 54 and 55: ERECTION AND SAFETY MANUAL The temp
Page 56 and 57: 5.8 WALL INSULATION Page 7.1-52 Rev
Page 58 and 59: 5.9 ROOF INSULATION Page 7.1-54 Rev
Page 60 and 61: ERECTION AND SAFETY MANUAL A four f
Page 62 and 63: ERECTION AND SAFETY MANUAL Backlapp
Page 70 and 71: 5.15 SEALING THE EAVE Page 7.1-66 R
Page 72 and 73: 5.17 PANEL ENDLAPS Page 7.1-68 Revi
Page 74 and 75: 5.19 INSTALLATION OF ROOF PANELS Pa
Page 76 and 77: 5.21 SKYLIGHT INSTALLATION Page 7.1
Page 82: 6.3 FLASHING CAULK AND LAP DETAILS
show all

ERECTION AND SAFETY MANUAL - Rigid Global Buildings

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?