Download the ST9340 Printer Reference Guide
Download the ST9340 Printer Reference Guide
Download the ST9340 Printer Reference Guide
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Understanding <strong>the</strong> printer messages<br />
Message What this message means What you can do<br />
Queuing Jobs The printer is sending one or more<br />
held jobs to print.<br />
Ready The printer is ready to receive and<br />
process print jobs.<br />
Ready Hex The printer is in Hex Trace mode and<br />
is ready to receive and process print<br />
jobs.<br />
Reattach The specified device is ei<strong>the</strong>r not fully<br />
connected to <strong>the</strong> printer or is<br />
experiencing a hardware failure.<br />
Remove Paper <br />
is one of <strong>the</strong> following:<br />
• Output bin x, where x is 1–3<br />
• Bins x - y, where x is 1–5, 2–6,<br />
6–10<br />
• Env Feeder<br />
The specified output bin, or bins, is<br />
full. The message would read as one<br />
of <strong>the</strong> following:<br />
• Remove Paper Standard Bin<br />
• Remove Paper Output Bin x,<br />
where x is <strong>the</strong> bin number<br />
• Remove Paper All Output Bins<br />
Res Reduced The printer is reducing <strong>the</strong> resolution<br />
of a page in <strong>the</strong> current job from 600<br />
dots per inch (dpi) to 300 dpi to<br />
prevent a 38 Memory Full error. Res<br />
Reduced remains on <strong>the</strong> display while<br />
<strong>the</strong> job prints.<br />
Resetting Active Bin The printer is resetting to <strong>the</strong> active<br />
bin in a linked set of bins.<br />
Resetting<br />
Maint Cnt Value<br />
The printer is resetting <strong>the</strong> counter<br />
that tracks wear on <strong>the</strong> fuser.<br />
Resetting <strong>the</strong> <strong>Printer</strong> The printer is resetting to <strong>the</strong> current<br />
default settings. Any active print jobs<br />
are canceled.<br />
265<br />
Wait for <strong>the</strong> message to clear.<br />
See also: Using <strong>the</strong> Print and<br />
Hold function<br />
Send a job to print.<br />
• Send a job to print. All data sent<br />
to <strong>the</strong> printer is printed in<br />
hexadecimal and character<br />
representation. Control strings<br />
are printed, not executed.<br />
• Turn <strong>the</strong> printer off and <strong>the</strong>n on to<br />
exit Hex Trace mode and return<br />
to Ready status.<br />
• Reestablish communication by<br />
removing <strong>the</strong> specified device<br />
and reattaching it to <strong>the</strong> printer.<br />
• Press Go to clear <strong>the</strong> message<br />
and continue printing without<br />
using <strong>the</strong> device.<br />
• In <strong>the</strong> case of a hardware failure,<br />
turn <strong>the</strong> printer off and back on. If<br />
<strong>the</strong> error recurs, turn <strong>the</strong> printer<br />
off, remove <strong>the</strong> specified device,<br />
and call for service.<br />
See also: Contacting service<br />
Remove <strong>the</strong> stack of paper from <strong>the</strong><br />
specified bin(s) to clear <strong>the</strong><br />
message.<br />
Press Menu to open <strong>the</strong> Job Menu<br />
and cancel <strong>the</strong> current job.<br />
Wait for <strong>the</strong> message to clear.<br />
Wait for <strong>the</strong> message to clear.<br />
Wait for <strong>the</strong> message to clear.<br />
See also: Using <strong>the</strong> operator<br />
panel to change printer settings
Change language