Masoneilan Products SVI II ESD - GE Energy

More documents

Recommendations

Info

GE Energy SVI II ESD Quick Start Acronyms Fail Dangerous Undetected Fail Dangerous Detected Failure that is dangerous and that is not being diagnosed by automatic stroke testing. Failure that is dangerous but is detected by automatic stroke testing. Fail Failure that does not cause a false trip or prevent the safety function but does cause loss of an automatic diagnostic and is not Annunciation Undetected detected by another diagnostic. Fail Annunciation Detected Fail No Effect Low Demand Mode Failure that does not cause a false trip or prevent the safety function but does cause loss of an automatic diagnostic or false diagnostic indication. Failure of a component that is part of the safety function but that has no effect on the safety function. Mode where the frequency of demands for operation made on a safety-related system is no greater than twice the proof test frequency. The following acronyms are related to safety functions of the SVI II ESD and are used throughout this document. FMEDA HFT MOC PFDavg PST SFF SIF SIL SIS Failure Modes, Effects and Diagnostic Analysis Hardware Fault Tolerance Management of Change. These are specific procedures often done when performing any work activities in compliance with government regulatory authorities. Average Probability of Failure on Demand Partial Stroke Test, a test used to detect failure modes in the PST Controller, actuator, and valve assembly. Safe Failure Fraction, the fraction of the overall failure rate of a device that results in either a safe fault or a diagnosed unsafe fault. Safety Instrumented Function, a set of equipment intended to reduce the risk due to a specific hazard (a safety loop). Safety Integrity Level, discrete level (one out of a possible four) for specifying the safety integrity requirements of the safety functions to be allocated to the E/E/PE safety-related systems where Safety Integrity Level 4 has the highest level of safety integrity and Safety Integrity Level 1 has the lowest. Safety Instrumented System – Implementation of one or more Safety Instrumented Functions. A SIS is composed of any combination of sensor (s), logic solver (s), and final element (s). 2
Safety Information Documentation Symbols Documentation Symbols Conventions used in this manual are as follows: Italicized letters are used when referencing a term used in the program display window. Italics is used for emphasis on important items. Fields where data is entered or user-entered data is italicized. Actions performed on buttons, checkboxes, etc. appear bolded. For example: Click Done. SVI II ESD instructions contain WARNINGS, CAUTIONS labels and Notes, where necessary, to alert you to safety related or other important information. Read the instructions carefully before installing and maintaining your instrument. Total compliance with all WARNING, and CAUTION notices is required for safe operation. WARNING Indicates a potentially hazardous situation, which if not avoided could result in serious injury or death. CAUTION Indicates a potentially hazardous situation, which if not avoided could result in instrument or property damage, or data loss. NOTE Indicates important facts and conditions. 3
Page 1 and 2: GE Energy 04/10 Masoneilan * Produc
Page 3: SVI II ESD Quick Start Guide Docume
Page 6 and 7: Operation, Setup, Commissioning. .
Page 8 and 9: GE Energy SVI II ESD Quick Start Gu
Page 12 and 13: GE Energy Product Safety SVI II ESD
Page 14 and 15: GE Energy SVI II ESD Device Descrip
Page 16 and 17: GE Energy SVI II ESD Quick Start SI
Page 18 and 19: GE Energy Installation SVI II ESD Q
Page 22 and 23: GE Energy Using the Quick Start Gui
Page 24 and 25: GE Energy SVI II ESD Quick Start Ne
Page 26 and 27: GE Energy SVI II ESD Quick Start 4.
Page 28 and 29: GE Energy SVI II ESD Quick Start Di
Page 30 and 31: GE Energy SVI II ESD Quick Start Mo
Page 32 and 33: GE Energy SVI II ESD Quick Start 12
Page 34 and 35: GE Energy SVI II ESD Quick Start Us
Page 36 and 37: GE Energy SVI II ESD Quick Start Ta
Page 38 and 39: GE Energy SVI II ESD Quick Start Do
Page 40 and 41: GE Energy SVI II ESD Quick Start El
Page 42 and 43: GE Energy SVI II ESD Quick Start An
Page 44 and 45: GE Energy SVI II ESD Quick Start To
Page 46 and 47: GE Energy SVI II ESD Quick Start Ch
Page 48 and 49: GE Energy SVI II ESD Quick Start Ou
Page 50 and 51: GE Energy SVI II ESD Quick Start Th
Page 58 and 59: GE Energy SVI II ESD Quick Start NO
Page 60 and 61:
GE Energy WARNING SVI II ESD Quick
Page 62 and 63:
GE Energy Calibration WARNING SVI I
Page 64 and 65:
GE Energy 7. Scroll to line 6 “EX
Page 66 and 67:
GE Energy SVI II ESD Quick Start St
Page 68 and 69:
GE Energy SVI II ESD Quick Start Ta
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
GE Energy SVI II ESD Quick Start ES
Page 76 and 77:
GE Energy SVI II ESD Quick Start Th
Page 78 and 79:
GE Energy SVI II ESD Quick Start 6
Page 80 and 81:
GE Energy SVI II ESD Quick Start HA
Page 82 and 83:
GE Energy SVI II ESD Quick Start 7.
Page 84:
GE Energy SVI II ESD Quick Start 9
show all

Masoneilan Products SVI II ESD - GE Energy

Create successful ePaper yourself

Delete template?

Save as template?