Masoneilan Products SVI II ESD - GE Energy

More documents

Recommendations

Info

GE Energy SVI II ESD Quick Start NOTE Install the Write Protect jumper on the SVI II ESD terminal board for normal operation. Refer to the SVI II ESD Instruction Manual SIL3, GEA18946 for further information. Normal Operation In Normal mode, the SVI II ESD responds to the input signal and positions the ESD valve accordingly. In configurations where the safety function is triggered by current, when the input signal current falls below 5.6 mA, the SVI II ESD de-energizes the ESD valve. In the same configuration, when the input signal current rises above 14 mA, the SVI II ESD energizes the ESD valve. In configurations where the safety function is triggered by a discrete 0 - 24 VDC signal, when the input signal voltage falls below 3V, the SVI II ESD de-energizes the ESD valve. In the same configuration, when the input signal voltage rises above 18 V, the SVI II ESD energizes the ESD valve. Manual Operation Setup In Manual mode, the valve does not respond to the input signal. Instead it remains stable in the position that the valve was in when manual mode was entered or a new position selected by using HART or pushbutton interface. However, the Shutdown function is activated if the signal is less than 5.6 mA (ASD and A/DSD) or 3 VDC (A/DSD and DSD). In the Setup mode, you can set calibration and configuration parameters. Additionally, you can run response time tests, step response tests, and valve signatures. 50
Setup, Calibration and Configuration any key Normal Cycling + Menu Normal Manual + View Data + View ERR + CLR ERR + + Run PST + * * * * any key Manual Mode Cycling Menu View Data Menu View Errors Menu Instant Action * * * * * * + + + + + View + + Setup Normal Manual Data View ERR CLR ERR MAN POS * * * - + * * CONFIG + + + + CALIB PST CONF MANUAL * * * Config Menu Calib Menu PST Conf Menu Configuration Figure 22 NORMAL Operation and MANUAL Menu Structures To perform configuration and calibration you can use either the pushbutton display, the HART handheld communicator, a HART Host with the DD loaded, or the ValVue ESD software. Refer to “Pushbuttons and Local Display” on page 45 or the SVI II ESD Instruction Manual SIL3, GEA18946 for instructions. The following section describes configuration and calibration with the optional local display and pushbuttons. 51
Page 1 and 2:
GE Energy 04/10 Masoneilan * Produc
Page 3:
SVI II ESD Quick Start Guide Docume
Page 6 and 7:
Operation, Setup, Commissioning. .
Page 8 and 9: GE Energy SVI II ESD Quick Start Gu
Page 10 and 11: GE Energy SVI II ESD Quick Start Ac
Page 12 and 13: GE Energy Product Safety SVI II ESD
Page 14 and 15: GE Energy SVI II ESD Device Descrip
Page 16 and 17: GE Energy SVI II ESD Quick Start SI
Page 18 and 19: GE Energy Installation SVI II ESD Q
Page 22 and 23: GE Energy Using the Quick Start Gui
Page 24 and 25: GE Energy SVI II ESD Quick Start Ne
Page 26 and 27: GE Energy SVI II ESD Quick Start 4.
Page 28 and 29: GE Energy SVI II ESD Quick Start Di
Page 30 and 31: GE Energy SVI II ESD Quick Start Mo
Page 32 and 33: GE Energy SVI II ESD Quick Start 12
Page 34 and 35: GE Energy SVI II ESD Quick Start Us
Page 36 and 37: GE Energy SVI II ESD Quick Start Ta
Page 38 and 39: GE Energy SVI II ESD Quick Start Do
Page 40 and 41: GE Energy SVI II ESD Quick Start El
Page 42 and 43: GE Energy SVI II ESD Quick Start An
Page 44 and 45: GE Energy SVI II ESD Quick Start To
Page 46 and 47: GE Energy SVI II ESD Quick Start Ch
Page 48 and 49: GE Energy SVI II ESD Quick Start Ou
Page 50 and 51: GE Energy SVI II ESD Quick Start Th
Page 60 and 61: GE Energy WARNING SVI II ESD Quick
Page 62 and 63: GE Energy Calibration WARNING SVI I
Page 64 and 65: GE Energy 7. Scroll to line 6 “EX
Page 66 and 67: GE Energy SVI II ESD Quick Start St
Page 74 and 75: GE Energy SVI II ESD Quick Start ES
Page 76 and 77: GE Energy SVI II ESD Quick Start Th
Page 78 and 79: GE Energy SVI II ESD Quick Start 6
Page 80 and 81: GE Energy SVI II ESD Quick Start HA
Page 82 and 83: GE Energy SVI II ESD Quick Start 7.
Page 84: GE Energy SVI II ESD Quick Start 9
show all

Masoneilan Products SVI II ESD - GE Energy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?