Masoneilan Products SVI II ESD - GE Energy

More documents

Recommendations

Info

GE Energy SVI II ESD Quick Start Double Acting PST Controller WARNING Isolate the valve from the process and disconnect air tubing from the positioner. Disconnect air fully to avoid injury or process damage. 1. Install the tubing to the air supply port (S). 2. For a double acting actuator - connect Output 1, labeled (I) to the inlet port of the actuator and Output 2, labeled (II) to the opposing actuator port (Figure 12). 3. Air supply: Supply pressure for double acting SVI II ESD: 30 -120 psi (2.07 - 8.28 bar) (207- 827.6 kPa) Minimum tubing diameter 1⁄4" (6 mm x 4 mm) Supply Output II Output I Figure 12 Air Ports on Double Acting Positioner 30
Installation and Connecting the Air Supply Checking the Air Supply After the tubing is installed, use the following procedure to connect the air supply. 1. Supply clean, dry compressed air to the filter regulator. 2. Turn on the air supply. 3. Adjust the filter regulator. 4. Supply pressure must be 10 psi greater than the spring range of the actuator but may not exceed the rated actuator pressure. Refer to the valve or actuator instruction manual. For detailed information on pneumatic connections refer to “Pneumatic Connections” on page 27. Checking the Air Supply Use this procedure to check the air supply. 1. Turn on the air supply. 2. Adjust the filter regulator. 3. Supply pressure must be a minimum of 10 psi greater than the spring range of the actuator but may not exceed the rated actuator pressure. Refer to the valve or actuator instruction manual. 4. Inspect the tubing connections between the filter-regulator and the positioner for leaks. 5. Verify that the tubing is not bent or crushed. 6. Verify that all fittings are leak tight. NOTE Do not use Teflon pipe seal tape. The Teflon tape can shred into particles that are harmful to the pneumatic components. Wiring the SVI II ESD There are two components to wiring the SVI II ESD; making an electrical connection for power and making a local control loop connection for HART communication. 31
Page 1 and 2: GE Energy 04/10 Masoneilan * Produc
Page 3: SVI II ESD Quick Start Guide Docume
Page 6 and 7: Operation, Setup, Commissioning. .
Page 8 and 9: GE Energy SVI II ESD Quick Start Gu
Page 10 and 11: GE Energy SVI II ESD Quick Start Ac
Page 12 and 13: GE Energy Product Safety SVI II ESD
Page 14 and 15: GE Energy SVI II ESD Device Descrip
Page 16 and 17: GE Energy SVI II ESD Quick Start SI
Page 18 and 19: GE Energy Installation SVI II ESD Q
Page 22 and 23: GE Energy Using the Quick Start Gui
Page 24 and 25: GE Energy SVI II ESD Quick Start Ne
Page 26 and 27: GE Energy SVI II ESD Quick Start 4.
Page 28 and 29: GE Energy SVI II ESD Quick Start Di
Page 30 and 31: GE Energy SVI II ESD Quick Start Mo
Page 32 and 33: GE Energy SVI II ESD Quick Start 12
Page 34 and 35: GE Energy SVI II ESD Quick Start Us
Page 36 and 37: GE Energy SVI II ESD Quick Start Ta
Page 40 and 41: GE Energy SVI II ESD Quick Start El
Page 42 and 43: GE Energy SVI II ESD Quick Start An
Page 44 and 45: GE Energy SVI II ESD Quick Start To
Page 46 and 47: GE Energy SVI II ESD Quick Start Ch
Page 48 and 49: GE Energy SVI II ESD Quick Start Ou
Page 50 and 51: GE Energy SVI II ESD Quick Start Th
Page 58 and 59: GE Energy SVI II ESD Quick Start NO
Page 60 and 61: GE Energy WARNING SVI II ESD Quick
Page 62 and 63: GE Energy Calibration WARNING SVI I
Page 64 and 65: GE Energy 7. Scroll to line 6 “EX
Page 66 and 67: GE Energy SVI II ESD Quick Start St
Page 74 and 75: GE Energy SVI II ESD Quick Start ES
Page 76 and 77: GE Energy SVI II ESD Quick Start Th
Page 78 and 79: GE Energy SVI II ESD Quick Start 6
Page 80 and 81: GE Energy SVI II ESD Quick Start HA
Page 82 and 83: GE Energy SVI II ESD Quick Start 7.
Page 84: GE Energy SVI II ESD Quick Start 9

Masoneilan Products SVI II ESD - GE Energy

Create successful ePaper yourself

Delete template?

Save as template?