Masoneilan Products SVI II ESD - GE Energy

More documents

Recommendations

Info

GE Energy SVI II ESD Quick Start 4. On vacuum service, the valve shaft may be drawn into the body by the vacuum acting on the shaft, but the magnetic coupling must be assembled flush with the mounting bracket with the shaft pulled fully out to its thrust bearing. Check that the endplay from the vacuum position to the fully extended position is less than 0.06 in. (1.524 mm) 5. Slide the magnet holder into the extension shaft. The location of the magnets is in the ring of the magnet holder. The magnetic axis is the imaginary line through the center of both magnets. 6. Rotate the magnet holder so that the magnet axis is vertical when the valve is in the closed position. 7. Align the end of the magnet holder flush with the end of the mounting bracket. Secure the magnet holder with two M6 set screws. 8. Slide the V-Seal over the magnet holder. 9. Secure the SVI II ESD onto the mounting bracket using four M6 x 20 mm Socket Head Cap Screws. 10. Ensure no interference exists with the position sensor protrusion. 11. Ensure that the V-Seal makes contact with the skirt around the position sensor protrusion on SVI II ESD housing. 18
Installation and Travel Sensor Alignment Travel Sensor Alignment Table 2 shows the general guidelines for travel sensor alignment. Review the table prior to installing the SVI II ESD on a rotary valve actuator for proper alignment of the magnet. Table 2 Travel Sensor Alignment Rotary Mounting System Stroke Direction Magnet Orientation Valve Position Sensor Counts Rotary 60° Rotation Clockwise with increasing setpoint Full Open or Full Closed -8000 +/- 1500 or +8000 +/- 1500 (-45°) >60° Rotation Counter Clockwise rotation with increasing setpoint Full Open or Full Closed -8000 +/- 1500 or +8000 +/- 1500 (+45°) General Rule for other configurations Any amount of rotation Clockwise or counterclockwise 50% Travel (Mid-Stroke) 0 +/- 1000 (0°) \ 19
Page 1 and 2: GE Energy 04/10 Masoneilan * Produc
Page 3: SVI II ESD Quick Start Guide Docume
Page 6 and 7: Operation, Setup, Commissioning. .
Page 8 and 9: GE Energy SVI II ESD Quick Start Gu
Page 10 and 11: GE Energy SVI II ESD Quick Start Ac
Page 12 and 13: GE Energy Product Safety SVI II ESD
Page 14 and 15: GE Energy SVI II ESD Device Descrip
Page 16 and 17: GE Energy SVI II ESD Quick Start SI
Page 18 and 19: GE Energy Installation SVI II ESD Q
Page 22 and 23: GE Energy Using the Quick Start Gui
Page 24 and 25: GE Energy SVI II ESD Quick Start Ne
Page 28 and 29: GE Energy SVI II ESD Quick Start Di
Page 30 and 31: GE Energy SVI II ESD Quick Start Mo
Page 32 and 33: GE Energy SVI II ESD Quick Start 12
Page 34 and 35: GE Energy SVI II ESD Quick Start Us
Page 36 and 37: GE Energy SVI II ESD Quick Start Ta
Page 38 and 39: GE Energy SVI II ESD Quick Start Do
Page 40 and 41: GE Energy SVI II ESD Quick Start El
Page 42 and 43: GE Energy SVI II ESD Quick Start An
Page 44 and 45: GE Energy SVI II ESD Quick Start To
Page 46 and 47: GE Energy SVI II ESD Quick Start Ch
Page 48 and 49: GE Energy SVI II ESD Quick Start Ou
Page 50 and 51: GE Energy SVI II ESD Quick Start Th
Page 58 and 59: GE Energy SVI II ESD Quick Start NO
Page 60 and 61: GE Energy WARNING SVI II ESD Quick
Page 62 and 63: GE Energy Calibration WARNING SVI I
Page 64 and 65: GE Energy 7. Scroll to line 6 “EX
Page 66 and 67: GE Energy SVI II ESD Quick Start St
Page 74 and 75: GE Energy SVI II ESD Quick Start ES
Page 76 and 77:
GE Energy SVI II ESD Quick Start Th
Page 78 and 79:
GE Energy SVI II ESD Quick Start 6
Page 80 and 81:
GE Energy SVI II ESD Quick Start HA
Page 82 and 83:
GE Energy SVI II ESD Quick Start 7.
Page 84:
GE Energy SVI II ESD Quick Start 9
show all

Masoneilan Products SVI II ESD - GE Energy

Create successful ePaper yourself

Delete template?

Save as template?