Masoneilan Products SVI II ESD - GE Energy

More documents

Recommendations

Info

GE Energy SVI II ESD Quick Start The SVI II ESD is manufactured by: Masoneilan/DRESSER 85 Bodwell Street Avon MA – 02322 – USA 2 Definitions and Abbreviations Abbr. Full Name Explanation SVI Smart Valve Interface Masoneilan digital instrument for controlling valves ESD Emergency Shut Down ASD Analog Safety Demand 4-20mA powers device and initiates Safety Function DSD Discrete Safety Demand 24VDC powers device and initiates Safety Function A/DSD Analog w/ Discrete Safety Demand 4-20mA powers device and 24VDC initiates Safety Function 3 General Requirements !WARNING! Failure to adhere to the requirements listed in this manual may cause loss of life and property. Installation and maintenance must be performed only by qualified personnel. Area Classification, Protection Type, Temperature Class, Gas Group, and Ingress protection must conform to the data indicated on the label. Wiring and conduit must conform to all local and national codes governing the installation. Wiring must be rated for at least 5ºC above the highest expected ambient temperature. Approved wire seals against ingress of water and dust are required and the 1/2 inch NPT fittings must be sealed with tape or thread sealant in order to meet the highest level of ingress protection. Doc Number ES-727 Written By P.Levesque 13DEC2006 Revision M ADR-003666 04/19/12 Checked T.Kabir 10JAN2007 Filename ES-727.DOC Page 3 of 11 Approved T. Kabir 10JAN2007 Copyright 2006 as an unpublished trade secret. This document and all information herein is the property of Dresser Flow Control, Dresser, Inc. It is confidential and must not be made public or copied and is subject to return upon demand. 68
Specifications and Hazardous Location Installation 3.1 Before powering the SVI II ESD: 1. Verify that the pneumatic and electronic cover screws are tightened. This is important to maintain the ingress protection level and the integrity of the flameproof enclosure. 2. If the Installation is Intrinsically Safe, then check that the proper barriers are installed and the field wiring meets local and national codes for an I.S. installation. Never install a device, which was previously installed without an intrinsically safe barrier, in an intrinsically safe system. 3. If the pneumatic system is powered by a combustible gas then the installation must be treated as Zone 0 or DIV I. 4. If the Installation is Non-Incendive, then check that all the electrical connections are made to Approved Devices and wiring meets local and national codes. 5. Verify that the markings on the label are consistent with the application. 6. Verify that the air supply pressure can not exceed: a. For Single Acting 100 PSI (6.8 Bar) b. For Double Acting 150 PSI (10 Bar) 4 Model Number Description of SVI II ESD SVI2- a b c d e f g h 1 Single Acting Standard Flow ASD w/ HART FM, CSA ATEX (XP, DIP, IS, NI) 2 Display DSD w/ HART Retransmit Double High Buttons Digital Out Acting Capacity Industrial 3 Plug-in Electronics Module (MNCB) A/DSD w/ HART 4 Display Buttons Offshore 5 FM, CSA, ATEX, TUV, IEC 6 ESD - Emergency Shutdown Style Pneumatics Capacity Display Electronics Communication Option Hazardous Certification 5 Flameproof and Dust Ignition Proof Requirements 5.1 General The 1/2 inch NPT fittings must enter the housing at least five full turns. The cover flange must be clean and free of corrosion products. 5.2 Cable Glands Certified cable glands are required based on the hazardous area the device is installed in. That is, the particular cable gland used must have the same certification as the tick-box checked off on the label (See Section 6, Figure 1). Doc Number ES-727 Written By P.Levesque 13DEC2006 Revision M ADR-003666 04/19/12 Checked T.Kabir 10JAN2007 Filename ES-727.DOC Page 4 of 11 Approved T. Kabir 10JAN2007 Copyright 2006 as an unpublished trade secret. This document and all information herein is the property of Dresser Flow Control, Dresser, Inc. It is confidential and must not be made public or copied and is subject to return upon demand. 69
Page 1 and 2:
GE Energy 04/10 Masoneilan * Produc
Page 3:
SVI II ESD Quick Start Guide Docume
Page 6 and 7:
Operation, Setup, Commissioning. .
Page 8 and 9:
GE Energy SVI II ESD Quick Start Gu
Page 10 and 11:
GE Energy SVI II ESD Quick Start Ac
Page 12 and 13:
GE Energy Product Safety SVI II ESD
Page 14 and 15:
GE Energy SVI II ESD Device Descrip
Page 16 and 17:
GE Energy SVI II ESD Quick Start SI
Page 18 and 19:
GE Energy Installation SVI II ESD Q
Page 20 and 21:
GE Energy SVI II ESD Quick Start Gu
Page 22 and 23:
GE Energy Using the Quick Start Gui
Page 24 and 25:
GE Energy SVI II ESD Quick Start Ne
Page 26 and 27: GE Energy SVI II ESD Quick Start 4.
Page 28 and 29: GE Energy SVI II ESD Quick Start Di
Page 30 and 31: GE Energy SVI II ESD Quick Start Mo
Page 32 and 33: GE Energy SVI II ESD Quick Start 12
Page 34 and 35: GE Energy SVI II ESD Quick Start Us
Page 36 and 37: GE Energy SVI II ESD Quick Start Ta
Page 38 and 39: GE Energy SVI II ESD Quick Start Do
Page 40 and 41: GE Energy SVI II ESD Quick Start El
Page 42 and 43: GE Energy SVI II ESD Quick Start An
Page 44 and 45: GE Energy SVI II ESD Quick Start To
Page 46 and 47: GE Energy SVI II ESD Quick Start Ch
Page 48 and 49: GE Energy SVI II ESD Quick Start Ou
Page 50 and 51: GE Energy SVI II ESD Quick Start Th
Page 52 and 53: GE Energy SVI II ESD Quick Start Gu
Page 58 and 59: GE Energy SVI II ESD Quick Start NO
Page 60 and 61: GE Energy WARNING SVI II ESD Quick
Page 62 and 63: GE Energy Calibration WARNING SVI I
Page 64 and 65: GE Energy 7. Scroll to line 6 “EX
Page 66 and 67: GE Energy SVI II ESD Quick Start St
Page 74 and 75: GE Energy SVI II ESD Quick Start ES
Page 78 and 79: GE Energy SVI II ESD Quick Start 6
Page 80 and 81: GE Energy SVI II ESD Quick Start HA
Page 82 and 83: GE Energy SVI II ESD Quick Start 7.
Page 84: GE Energy SVI II ESD Quick Start 9
show all

Masoneilan Products SVI II ESD - GE Energy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?