Masoneilan Products SVI II ESD - GE Energy

More documents

Recommendations

Info

GE Energy SVI II ESD Quick Start HAZARDOUS LOCATION SEE 7.1, 7.2 Equi-Potential Switch (See 7.3.5) NON-HAZARDOUS LOCATION - UNSPECIFIED EXCEPT THAT BARRIERS MUST NOT BE SUPPLIED FROM NOR CONTAIN UNDER NORMAL OR ABNORMAL CONDITIONS A SOURCE OF POTENTIAL WITH RESPECT TO EARTH IN EXCESS OF 250 VOLTS RMS OR 250 VOLTS DC Shunt Zener Diode Safety Barrier Controller Output Type (See 7.3.6) Optional Hand Held Communicator (See 7.3) 3 4 1 2 24 VDC Trip Signal from DCS (A/DSD & DSD ONLY) SVI II ESD PV 1-5VDC 4-20mA OUT SW 1, SW 2 4-20mA IN 24 VDC IN DI + - + - + - + - + - Optional Hand Held Communicator (See 7.3) Optional Field Load 3 4 3 4 3 4 3 4 250Ω 1 2 1 2 1 2 1 2 LOAD Optional Hand Held Communicator (See 7.3) 4-20 mA Trip Signal from DCS (ASD & A/DSD ONLY) Shunt Zener Diode Safety Barrier - Controller Output Type (See 7.3.1, 7.3.3) 24 VDC from DCS To DCS DI Shunt Zener Diode Safety Barrier Switch Type Barrier (See 7.3.4) 24 VDC from DCS 1-5VDC To DCS Transmitter Barrier Type w/ Internal or External Sense Resistor (See 7.3.2) Shunt Zener Diode Safety Barrier Controller Output Type (See 7.3.1, 7.3.3) 1-5VDC To DCS Optional I.S. TRANSMITTER + - Cable Shield Each intrinsically safe cable must include a grounded shield or be run in a separate grounded metal conduit 3 250Ω 4 24 VDC from 1 Control System 2 Shunt Zener Diode Safety Barrier Transmitter Type w/ Internal or External Sensing Resistor Equi-Potential (See 7.3.3) Doc Number ES-727 Written By P.Levesque 13DEC2006 Revision M ADR-003666 04/19/12 Checked T.Kabir 10JAN2007 Filename ES-727.DOC Page 7 of 11 Approved T. Kabir 10JAN2007 Copyright 2006 as an unpublished trade secret. This document and all information herein is the property of Dresser Flow Control, Dresser, Inc. It is confidential and must not be made public or copied and is subject to return upon demand. 72
Specifications and Hazardous Location Installation 7 Notes for Intrinsically Safe Installation 7.1 Hazardous Locations Refer to the device label for the description of the environment in which the device may be installed. 7.2 Field Wiring Intrinsically Safe wiring must be made with grounded shielded cable or installed in grounded metal conduit. The electrical circuit in the hazardous area must be capable of withstanding an A.C. test voltage of 500 volts R.M.S. to earth or frame of the apparatus for 1 minute. Installation must be in accordance with Masoneilan guidelines. The installation including the barrier earthing requirements must comply with the installation requirements of the country of use. Factory Mutual requirements (USA): ANSI/ISA RP12.6 (Installation of Intrinsically Safe Systems for Hazardous (Classified) Locations) and the National Electrical Code, ANSI/NFPA 70. Division 2 installations must be installed per the National Electrical Code, ANSI/NFPA 70. See 7.3.2. In group A installations, conduit seal required within 18 inches of enclosure entrance. CSA requirements (Canada): Canadian Electrical Code Part 1. Division 2 installations must be installed per the Canadian Electrical Code Division 2 Wiring Methods. See 7.3.2. ATEX requirements (EU): Intrinsically safe installations must be installed per EN60079-10 and EN60079-14 as they apply to the specific Category. 7.3 Entity Requirements Cable capacitance and inductance plus the I.S. apparatus unprotected capacitance (Ci) and inductance (Li) must not exceed the allowed capacitance (Ca) and inductance (La) indicated on the associated apparatus. If the optional Hand Held Communicator is used on the Hazardous Area side of the barrier, then the capacity and inductance of the communicator must be added and the communicator must be agency approved for use in the hazardous area. Also, the current output of the Hand Held Communicator must be included in the current output of the associated equipment. The barriers may be active or passive and from any certified manufacturer as long as the barriers comply with the listed entity parameters. 7.3.1 SVI II ESD 4-20 mA IN Terminals (+) and (-) These terminals power the SVI II-ESD. The barrier is the Controller Output Type, for example MTL 728. Table 1, 4-20mA IN Entity Parameters Vmax Imax Ci Li Pmax Entity Parameters 30 VDC 125 mA 7 nF 10 uH 900 mW Doc Number ES-727 Written By P.Levesque 13DEC2006 Revision M ADR-003666 04/19/12 Checked T.Kabir 10JAN2007 Filename ES-727.DOC Page 8 of 11 Approved T. Kabir 10JAN2007 Copyright 2006 as an unpublished trade secret. This document and all information herein is the property of Dresser Flow Control, Dresser, Inc. It is confidential and must not be made public or copied and is subject to return upon demand. 73
Page 1 and 2:
GE Energy 04/10 Masoneilan * Produc
Page 3:
SVI II ESD Quick Start Guide Docume
Page 6 and 7:
Operation, Setup, Commissioning. .
Page 8 and 9:
GE Energy SVI II ESD Quick Start Gu
Page 10 and 11:
GE Energy SVI II ESD Quick Start Ac
Page 12 and 13:
GE Energy Product Safety SVI II ESD
Page 14 and 15:
GE Energy SVI II ESD Device Descrip
Page 16 and 17:
GE Energy SVI II ESD Quick Start SI
Page 18 and 19:
GE Energy Installation SVI II ESD Q
Page 20 and 21:
GE Energy SVI II ESD Quick Start Gu
Page 22 and 23:
GE Energy Using the Quick Start Gui
Page 24 and 25:
GE Energy SVI II ESD Quick Start Ne
Page 26 and 27:
GE Energy SVI II ESD Quick Start 4.
Page 28 and 29:
GE Energy SVI II ESD Quick Start Di
Page 30 and 31: GE Energy SVI II ESD Quick Start Mo
Page 32 and 33: GE Energy SVI II ESD Quick Start 12
Page 34 and 35: GE Energy SVI II ESD Quick Start Us
Page 36 and 37: GE Energy SVI II ESD Quick Start Ta
Page 38 and 39: GE Energy SVI II ESD Quick Start Do
Page 40 and 41: GE Energy SVI II ESD Quick Start El
Page 42 and 43: GE Energy SVI II ESD Quick Start An
Page 44 and 45: GE Energy SVI II ESD Quick Start To
Page 46 and 47: GE Energy SVI II ESD Quick Start Ch
Page 48 and 49: GE Energy SVI II ESD Quick Start Ou
Page 50 and 51: GE Energy SVI II ESD Quick Start Th
Page 52 and 53: GE Energy SVI II ESD Quick Start Gu
Page 58 and 59: GE Energy SVI II ESD Quick Start NO
Page 60 and 61: GE Energy WARNING SVI II ESD Quick
Page 62 and 63: GE Energy Calibration WARNING SVI I
Page 64 and 65: GE Energy 7. Scroll to line 6 “EX
Page 66 and 67: GE Energy SVI II ESD Quick Start St
Page 74 and 75: GE Energy SVI II ESD Quick Start ES
Page 76 and 77: GE Energy SVI II ESD Quick Start Th
Page 78 and 79: GE Energy SVI II ESD Quick Start 6
Page 82 and 83: GE Energy SVI II ESD Quick Start 7.
Page 84: GE Energy SVI II ESD Quick Start 9
show all

Masoneilan Products SVI II ESD - GE Energy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?