Masoneilan Products SVI II ESD - GE Energy

More documents

Recommendations

Info

GE Energy Using the Quick Start Guide SVI II ESD Quick Start The SVI II ESD Quick Start Guide is intended to help an experienced Field Engineer install, setup, and calibrate an SVI II ESD in the most efficient manner possible. This document provides basic installation and setup instructions and is not intended to replace the in-depth information contained in the SVI II ESD Instruction Manual GEA18946. If you experience problems that are not documented in this guide refer to the Masoneilan SVI II ESD Instruction Manual SIL3, GEA18946, call your local representative, or go to www.dressermasoneilan.com. Sales offices are listed on the last page of this document Installation The steps necessary to complete the SVI II ESD installation and software setup are outlined in Table 1. Table 1 SVI II ESD Installation Steps Step No. Procedure Reference 1 2 3 4 5 Attach mounting bracket to the actuator. Install the SVI II ESD magnetic assembly (rotary valves only). Assemble the SVI II ESD on the bracket that is mounted to the valve actuator. Connect the pneumatic tubing to the SVI II ESD. Connect the air supply to the SVI II ESD. See page page 17 for rotary valve and page 21 for reciprocating valve instructions. See page 17 for instructions. See page 17 for rotary valve and page 21 for reciprocating valve instructions. See page 27 for instructions. See page 31 for instructions. 6 Install the wiring for the SVI II ESD. See page 31 for instructions. 7 Connect the PST controller to the HART Control Loop segment by installing the SVI II ESD wiring. See page 34 for instructions. 8 Power up the SVI II ESD. See page 35 for instructions. 14
Installation and Physical Location and Table 1 SVI II ESD Installation Steps Step No. Procedure Reference 9 If appropriate, configure/calibrate using ValVue ESD If appropriate, configure/calibrate using a HART Hand Held Communicator See page 51 and page 54 for instructions. See page 55 for instructions. WARNING Failure to adhere to the requirements listed in this manual may cause loss of life and property. Before installing, using, or carrying out any maintenance tasks associated with this instrument, READ THE INSTRUCTIONS CAREFULLY. Physical Location and Placement Guidelines When determining the location of the SVI II ESD adhere to the following guidelines: The SVI II ESD must be accessible with sufficient room for cabling and pneumatic connections and must allow manual proof testing. Pneumatic piping to the actuator must be kept as short and straight as possible to minimize the airflow restrictions and potential clogging of the line. Long or kinked pneumatic tubes may also increase the valve closure time. The Breather/Vent port must be accessible and must be inspected for obstruction during manual proof testing. The SVI II ESD must be mounted in a mild vibration environment (see specifications at the end of this document). If excessive vibration can be expected special precautions must be taken to ensure the integrity of electrical and pneumatic connectors or reduce the vibration using appropriate damping mounts. 15
Page 1 and 2: GE Energy 04/10 Masoneilan * Produc
Page 3: SVI II ESD Quick Start Guide Docume
Page 6 and 7: Operation, Setup, Commissioning. .
Page 8 and 9: GE Energy SVI II ESD Quick Start Gu
Page 10 and 11: GE Energy SVI II ESD Quick Start Ac
Page 12 and 13: GE Energy Product Safety SVI II ESD
Page 14 and 15: GE Energy SVI II ESD Device Descrip
Page 16 and 17: GE Energy SVI II ESD Quick Start SI
Page 18 and 19: GE Energy Installation SVI II ESD Q
Page 24 and 25: GE Energy SVI II ESD Quick Start Ne
Page 26 and 27: GE Energy SVI II ESD Quick Start 4.
Page 28 and 29: GE Energy SVI II ESD Quick Start Di
Page 30 and 31: GE Energy SVI II ESD Quick Start Mo
Page 32 and 33: GE Energy SVI II ESD Quick Start 12
Page 34 and 35: GE Energy SVI II ESD Quick Start Us
Page 36 and 37: GE Energy SVI II ESD Quick Start Ta
Page 38 and 39: GE Energy SVI II ESD Quick Start Do
Page 40 and 41: GE Energy SVI II ESD Quick Start El
Page 42 and 43: GE Energy SVI II ESD Quick Start An
Page 44 and 45: GE Energy SVI II ESD Quick Start To
Page 46 and 47: GE Energy SVI II ESD Quick Start Ch
Page 48 and 49: GE Energy SVI II ESD Quick Start Ou
Page 50 and 51: GE Energy SVI II ESD Quick Start Th
Page 58 and 59: GE Energy SVI II ESD Quick Start NO
Page 60 and 61: GE Energy WARNING SVI II ESD Quick
Page 62 and 63: GE Energy Calibration WARNING SVI I
Page 64 and 65: GE Energy 7. Scroll to line 6 “EX
Page 66 and 67: GE Energy SVI II ESD Quick Start St
Page 72 and 73:
GE Energy SVI II ESD Quick Start Ta
Page 74 and 75:
GE Energy SVI II ESD Quick Start ES
Page 76 and 77:
GE Energy SVI II ESD Quick Start Th
Page 78 and 79:
GE Energy SVI II ESD Quick Start 6
Page 80 and 81:
GE Energy SVI II ESD Quick Start HA
Page 82 and 83:
GE Energy SVI II ESD Quick Start 7.
Page 84:
GE Energy SVI II ESD Quick Start 9
show all

Masoneilan Products SVI II ESD - GE Energy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?