Masoneilan Products SVI II ESD - GE Energy

More documents

Recommendations

Info

GE Energy SVI II ESD Quick Start 6 Intrinsically Safe Requirements 6.1 DIV 2 (No I.S. Barrier) WARNING: EXPLOSION HAZARD – Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous. 6.2 Category II (Zone 0) For operation in hazardous area Category II 1, over-voltage protection of the electrical connections needs to be installed according to EN 60079-14 For operation in hazardous area Category II 1 the ambient temperature needs to be lowered according to the requirements of EN 1127-1 (reduction factor of 80%). The maximum allowed ambient temperature for Category 1 inclusive the requirement of EN1127-1 is: T6: Ta = -40°C to +43°C T5: Ta = -40°C to +55°C T4: Ta = -40°C to +83°C 6.3 Category II 1 (Zone 0) “X” Marking on label - Since the SVI2-abcdefgh (“SVI-II ESD”) enclosures contain greater than 10% aluminum, care must be taken during installation to avoid impacts or friction that could create an ignition source. Doc Number ES-727 Written By P.Levesque 13DEC2006 Revision M ADR-003666 04/19/12 Checked T.Kabir 10JAN2007 Filename ES-727.DOC Page 5 of 11 Approved T. Kabir 10JAN2007 Copyright 2006 as an unpublished trade secret. This document and all information herein is the property of Dresser Flow Control, Dresser, Inc. It is confidential and must not be made public or copied and is subject to return upon demand. 70
Specifications and Hazardous Location Installation Figure 1, Description of Hazardous Location Markings Applicable Model Numbers: SVI2-abcdefgh, where “a” thru “h” can take on the following values: a = 6 ; b = 1,2 ; c = 1,2 ; d = 1,2,3,4 ; e = 3 ; f = 1 ; g = 1,2,3 ; h = 1,5 Name and location of manufacturer ATEX Certificate Number ATEX Logo EU Community Compliance Mark Factory Mutual and CSA Logos Number of Notified Body Types of protection and group designations IEC Logo and Certificate Number Protection type, gas group Model Designation Requirement to use high temperature rated wiring Operating Temperature Requirement to - follow certified installation drawing Voltage, Current and Pressure operating limits Surface temperature ignition codes for gas TÜV SIL Trade Name and Function Function may be: Analog Safety Demand (ASD) Discrete Safety Demand (DSD) Analog with Discrete Safety Demand (A/DSD) Serial Number Enclosure Type Figure 2, Intrinsically Safe Installation Wiring Requirements Doc Number ES-727 Written By P.Levesque 13DEC2006 Revision M ADR-003666 04/19/12 Checked T.Kabir 10JAN2007 Filename ES-727.DOC Page 6 of 11 Approved T. Kabir 10JAN2007 Copyright 2006 as an unpublished trade secret. This document and all information herein is the property of Dresser Flow Control, Dresser, Inc. It is confidential and must not be made public or copied and is subject to return upon demand. 71
Page 1 and 2:
GE Energy 04/10 Masoneilan * Produc
Page 3:
SVI II ESD Quick Start Guide Docume
Page 6 and 7:
Operation, Setup, Commissioning. .
Page 8 and 9:
GE Energy SVI II ESD Quick Start Gu
Page 10 and 11:
GE Energy SVI II ESD Quick Start Ac
Page 12 and 13:
GE Energy Product Safety SVI II ESD
Page 14 and 15:
GE Energy SVI II ESD Device Descrip
Page 16 and 17:
GE Energy SVI II ESD Quick Start SI
Page 18 and 19:
GE Energy Installation SVI II ESD Q
Page 20 and 21:
GE Energy SVI II ESD Quick Start Gu
Page 22 and 23:
GE Energy Using the Quick Start Gui
Page 24 and 25:
GE Energy SVI II ESD Quick Start Ne
Page 26 and 27:
GE Energy SVI II ESD Quick Start 4.
Page 28 and 29: GE Energy SVI II ESD Quick Start Di
Page 30 and 31: GE Energy SVI II ESD Quick Start Mo
Page 32 and 33: GE Energy SVI II ESD Quick Start 12
Page 34 and 35: GE Energy SVI II ESD Quick Start Us
Page 36 and 37: GE Energy SVI II ESD Quick Start Ta
Page 38 and 39: GE Energy SVI II ESD Quick Start Do
Page 40 and 41: GE Energy SVI II ESD Quick Start El
Page 42 and 43: GE Energy SVI II ESD Quick Start An
Page 44 and 45: GE Energy SVI II ESD Quick Start To
Page 46 and 47: GE Energy SVI II ESD Quick Start Ch
Page 48 and 49: GE Energy SVI II ESD Quick Start Ou
Page 50 and 51: GE Energy SVI II ESD Quick Start Th
Page 52 and 53: GE Energy SVI II ESD Quick Start Gu
Page 58 and 59: GE Energy SVI II ESD Quick Start NO
Page 60 and 61: GE Energy WARNING SVI II ESD Quick
Page 62 and 63: GE Energy Calibration WARNING SVI I
Page 64 and 65: GE Energy 7. Scroll to line 6 “EX
Page 66 and 67: GE Energy SVI II ESD Quick Start St
Page 74 and 75: GE Energy SVI II ESD Quick Start ES
Page 76 and 77: GE Energy SVI II ESD Quick Start Th
Page 80 and 81: GE Energy SVI II ESD Quick Start HA
Page 82 and 83: GE Energy SVI II ESD Quick Start 7.
Page 84: GE Energy SVI II ESD Quick Start 9
show all

Masoneilan Products SVI II ESD - GE Energy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?