Engineering plastics – The Manual - F.wood-supply.dk

Material standard values
Material
TECAPEEK
ELS nano
TECAPEEK
TF10
blue
TECAPEEK
ID
TECAPEEK
MT
TECAPEEK
MT
black
TECAPEEK
MT
blue
TECAPEEK
MT
green
TECAPEEK
MT
yellow
TECAPEEK
MT
bright red
TECAPEEK
MT
ivory
Chemical Designation
PEEK PEEK PEEK PEEK PEEK PEEK PEEK PEEK PEEK PEEK
Fillers
CNT
PTFE
Density
(DIN EN ISO 1183)
Mechanical properties
Modulus of elasticity (tensile test)
(DIN EN ISO 527-2)
Tensile strength
(DIN EN ISO 527-2)
Tensile strength at yield
(DIN EN ISO 527-2)
Elongation at yield
(DIN EN ISO 527-2)
Elongation at break
(DIN EN ISO 527-2)
Modulus of elasticity (flexural test)
(DIN EN ISO 178)
Flexural strength
(DIN EN ISO 178)
Compression modulus
(EN ISO 604)
Compressive strength (1% / 2%)
(EN ISO 604)
Impact strength (Charpy)
(DIN EN ISO 179-1eU)
Notched impact strength (Charpy)
(DIN EN ISO 179-1eA)
Ball intendation hardness
(ISO 2039-1)
Thermal properties
Glass transition temperature
(DIN 53765)
Melting temperature
(DIN 53765)
Service temperature,
short term
Service temperature,
long term
Thermal expansion (CLTE),
23 – 60 °C (DIN EN ISO 11359-1;2)
Thermal expansion (CLTE),
23 – 100 °C (DIN EN ISO 11359-1;2)
Specific heat
(ISO 22007-4:2008)
Thermal conductivity
(ISO 22007-4:2008)
Electrical properties
Surface resistance
(DIN IEC 60093)
Miscellaneous data
Water absorption 24h / 96h (23 °C)
(DIN EN ISO 62)
Resistance
to hot water / bases
Resistance to weathering
Flammability (UL94)
(DIN IEC 60695-11-10;)
[g / cm³]
[MPa]
[MPa]
[MPa]
[%]
[%]
[MPa]
[MPa]
[MPa]
[MPa]
[kJ / m²]
[kJ / m²]
[MPa]
[°C]
[°C]
[°C]
[°C]
[10 -5 K -1 ]
[10 -5 K -1 ]
[J / (g*K)]
[W/(m*K)]
[Ω]
[%]
1.36 1.38 1.49 1.31 1.31 1.34 1.32 1.38 1.36 1.42
4,800 3,400 4,600 4,200 4,200 4,300 4,100 4,400 4,200 4,400
106 95 111 116 114 113 116 113 108 114
106 95 111 116 114 113 116 113 108 114
4 5 4 5 5 5 5 5 4 4
4 8 6 15 13 11 17 10 6 12
4,700 3,900 3,700 4,200 4,100 4,300 4,200 4,300 4,500 4,400
178 149 166 175 171 173 172 169 177 171
3,600 3,000 4,800 3,400 3,400 3,400 3,400 3,400 3,500 3,400
27 / 47 22 / 39 25 / 46 23 / 43 23 / 44 17 / 35 17 / 35 17 / 35 22 / 40 24 / 44
58 48 72 n.b. n.b. n.b. n.b. n.b. 50 n.b.
4 5 7 4 5 4
253 220 260 253 243 248 250 257 244 250
147 157 150 150 151 151 151 151 151 150
341 340 341 342 341 341 341 341 341 340
300 300 300 300 300 300 300 300 300 300
260 260 260 260 260 260 260 260 260 260
5 6 5 5 5 5 5 5 5 5
5 6 5 5 5 5 5 5 5 5
1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1
0.46 0.27 0.27 0.3 0.28 0.28 0.28 0.27
10 4 10 13 10 14 10 12 10 14 10 14 10 14 10 14 10 14
0.02 / 0.03 0.02 / 0.03 0.02 / 0.03 0.02 / 0.03 0.02 / 0.03 0.02 / 0.03 0.02 / 0.03 0.02 / 0.03 0.02 / 0.03 0.02 / 0.03
+ + + + + + + + + +
(+) – – – – – – – – –
V0 V0 V0 V0 V0 V0 V0 V0 V0 V0
Data generated directly after machining (standard
climate Germany). For polyamides the values strongly
depend on the humidity content.
Test specimen to DIN EN ISO 527-2
+ good resistance
(+) limited resistance
– poor resistance (depending on concen -
tration, time and temperature)
n.b. not broken
n.a. not applicable
(a) Glass transition temperature
testing according to DIN EN ISO 11357
(b) Thermal conductivity testing according to ISO 8302
(c) Thermal conductivity testing according to ASTM E1530
(d) Surface resistance testing according to ASTM D 257
94