Engineering plastics – The Manual - F.wood-supply.dk

Material
TECAPEEK
CF30 MT
TECAPEEK
CLASSIX
white
TECAPEEK
TS
TECAPEEK
CMF
TECAPEEK
CMF
grey
TECAPEEK
HT
black
TECAPEEK
ST
black
TECATEC
PEEK CW50
TECATEC TECATOR
PEKK CW60 5013
Chemical Designation
PEEK PEEK PEEK PEEK PEEK PEK PEKEKK PEEK PEKK PAI
Fillers
carbon
fibres
mineral
filler
ceramic
ceramic
Density
(DIN EN ISO 1183)
Mechanical properties
Modulus of elasticity (tensile test)
(DIN EN ISO 527-2)
Tensile strength
(DIN EN ISO 527-2)
Tensile strength at yield
(DIN EN ISO 527-2)
Elongation at yield
(DIN EN ISO 527-2)
Elongation at break
(DIN EN ISO 527-2)
Modulus of elasticity (flexural test)
(DIN EN ISO 178)
Flexural strength
(DIN EN ISO 178)
Compression modulus
(EN ISO 604)
Compressive strength (1% / 2%)
(EN ISO 604)
Impact strength (Charpy)
(DIN EN ISO 179-1eU)
Notched impact strength (Charpy)
(DIN EN ISO 179-1eA)
Ball intendation hardness
(ISO 2039-1)
Thermal properties
Glass transition temperature
(DIN 53765)
Melting temperature
(DIN 53765)
Service temperature,
short term
Service temperature,
long term
Thermal expansion (CLTE),
23 – 60 °C (DIN EN ISO 11359-1;2)
Thermal expansion (CLTE),
23 – 100 °C (DIN EN ISO 11359-1;2)
Specific heat
(ISO 22007-4:2008)
Thermal conductivity
(ISO 22007-4:2008)
Electrical properties
Surface resistance
(DIN IEC 60093)
Miscellaneous data
Water absorption 24h / 96h (23 °C)
(DIN EN ISO 62)
Resistance
to hot water / bases
Resistance to weathering
Flammability (UL94)
(DIN IEC 60695-11-10;)
[g / cm³]
[MPa]
[MPa]
[MPa]
[%]
[%]
[MPa]
[MPa]
[MPa]
[MPa]
[kJ / m²]
[kJ / m²]
[MPa]
[°C]
[°C]
[°C]
[°C]
[10 -5 K -1 ]
[10 -5 K -1 ]
[J / (g*K)]
[W/(m*K)]
[Ω]
[%]
1.42 1.4 1.49 1.65 1.65 1.31 1.32 1.49 1.61 1.4
6,000 4,700 5,700 5,500 5,500 4,600 4,600 53,200 54,300 3,800
115 117 110 105 105 120 134 491 585 151
115 117 110 102 102 120 134 151
5 5 4 3 4 4 5
5 11 4 4 5 5 13 21
6,000 4,400 5,900 5,500 5,500 4,600 4,600 48,900 50,900 3,900
188 177 175 170 170 192 193 813 960
4,500 3,500 4,300 4,300 4,300 3,500 3,500 4,050 5,100
23 / 44 25 / 45 17 / 34 25 / 46 25 / 46 25 / 45 24 / 42 51 / 509
58 n.b. n.b. 65 35 n.b. n.b.
5 7 4 4 13.2
318 263 290 286 286 282 275 240
146 150 151 151 151 160 165 143 165 280
341 341 339 339 339 375 384 343 380 n.a.
300 300 300 300 300 300 300 270
260 260 260 260 260 260 260 260 260 250
5 5 4 5 5 5 5
5 5 4 5 5 5 5
1.7 1.0 1.0 1.0
0.59 0.30 0.38 0.38 0.29 (c)
10 8 10 14 10 13 10 14 10 13 10 9 10 9 10 18 (d)
0.02 / 0.03 0.02 / 0.03 0.02 / 0.03 0.02 / 0.03 0.02 / 0.03 0.02 / 0.04 0.02 / 0.03
+ + + + + + + + + –
– – – – – (+) (+) – –
V0 V0 V0 V0 V0 V0 V0 V0 V0 V0
The corresponding values and information are no minimum
or maximum values, but guideline values that can be used
primarily for comparison purposes for material selection.
These values are within the normal tolerance range of
product properties and do not represent guaranteed property
values. Therefore they shall not be used for specification
purposes. Unless otherwise noted, these values were
determined by tests at reference dimensions (typically rods
with diameter 40-60 mm according to DIN EN 15860) on
extruded, cast, compression moulded and machined specimens.
As the properties depend on the dimensions of the
semi-finished products and the orientation in the component
(esp. in reinforced grades), the material may not be used
without separate testing under individual circumstances.
Data sheet values are subject to periodic review, the most
recent update can be found at www.ensinger-online.com
Technical changes reserved.
95