Engineering plastics – The Manual - F.wood-supply.dk

Material
TECASINT
2031
TECASINT
2391
TECASINT
4011
TECASINT
4021
TECASINT
4111
TECASINT
4121
TECASINT
5051
TECASINT
5201 SD
TECASINT
8001
Chemical Designation
PI PI PI PI PI PI PAI PAI PTFE
Fillers
40%
graphite
15% molybdenum
disulfide
15%
graphite
15%
graphite
30%
glass fibres
carbon
fibres,
glass fibres
20%
polyimide
Density
(DIN EN ISO 1183)
Mechanical properties
Modulus of elasticity (tensile test)
(DIN EN ISO 527-2)
Tensile strength
(DIN EN ISO 527-2)
Tensile strength at yield
(DIN EN ISO 527-2)
Elongation at yield
(DIN EN ISO 527-2)
Elongation at break
(DIN EN ISO 527-2)
Modulus of elasticity (flexural test)
(DIN EN ISO 178)
Flexural strength
(DIN EN ISO 178)
Compression modulus
(EN ISO 604)
Compressive strength (1% / 2%)
(EN ISO 604)
Impact strength (Charpy)
(DIN EN ISO 179-1eU)
Notched impact strength (Charpy)
(DIN EN ISO 179-1eA)
Ball intendation hardness
(ISO 2039-1)
Thermal properties
Glass transition temperature
(DIN 53765)
Melting temperature
(DIN 53765)
Service temperature,
short term
Service temperature,
long term
Thermal expansion (CLTE),
23 – 60 °C (DIN EN ISO 11359-1;2)
Thermal expansion (CLTE),
23 – 100 °C (DIN EN ISO 11359-1;2)
Specific heat
(ISO 22007-4:2008)
Thermal conductivity
(ISO 22007-4:2008)
Electrical properties
Surface resistance
(DIN IEC 60093)
Miscellaneous data
Water absorption 24h / 96h (23 °C)
(DIN EN ISO 62)
Resistance
to hot water / bases
Resistance to weathering
Flammability (UL94)
(DIN IEC 60695-11-10;)
[g / cm³]
[MPa]
[MPa]
[MPa]
[%]
[%]
[MPa]
[MPa]
[MPa]
[MPa]
[kJ / m²]
[kJ / m²]
[MPa]
[°C]
[°C]
[°C]
[°C]
[10 -5 K -1 ]
[10 -5 K -1 ]
[J / (g*K)]
[W/(m*K)]
[Ω]
[%]
1.59 1.54 1.41 1.49 1.46 1.53 1.57 1.54 1.88
6,300 4,400 4,000 4,943 7,000 6,600 5,800 4,500
65 95 130 93 100 34 94 85 15
2.1 2.9 4.5 3 1.7 0.5 3.4 4.0 200
5,200 4,136 4,300 4,930 6,100 6,100 6,625 4,200
87.5 137 180 131 160 113 163 135
2,027 2,200 2,100 2,067 2,500 2,200 2,590
131 253 40 208 250 200 260 240
14.2 87 24.4 24 11 27.3 17.8
3.3 9.6 4.8 1.1 1.4 5.1 2.8
370 (a) 370 (a) 260 (a) 260 (a) n.a. (a) n.a. (a) 340 (a) 340 (a) 20 (a)
– – 300 300 250
1.04 1
0.4 (b) 0.35 (b) 0.25 (b)
10 16 (d) 10 16 (d) 10 14 10 11
V0 V0 V0 V0 V0 V0 V0 V0 V0
The corresponding values and information are no minimum
or maximum values, but guideline values that can be used
primarily for comparison purposes for material selection.
These values are within the normal tolerance range of
product properties and do not represent guaranteed property
values. Therefore they shall not be used for specification
purposes. Unless otherwise noted, these values were
determined by tests at reference dimensions (typically rods
with diameter 40-60 mm according to DIN EN 15860) on
extruded, cast, compression moulded and machined specimens.
As the properties depend on the dimensions of the
semi-finished products and the orientation in the component
(esp. in reinforced grades), the material may not be used
without separate testing under individual circumstances.
Data sheet values are subject to periodic review, the most
recent update can be found at www.ensinger-online.com
Technical changes reserved.
97