Engineering plastics – The Manual - F.wood-supply.dk

Material standard values
Material
TECATOR
5031 PVX
TECASINT
1011
TECASINT
1021
TECASINT
1031
TECASINT
1041
TECASINT
1061
TECASINT
1101
TECASINT
1611
TECASINT
2011
TECASINT
2021
Chemical Designation
PAI PI PI PI PI PI PI PI PI PI
Fillers
graphite,
PTFE
15%
graphite
40%
graphite
30% molybdenum
disulfide
15%
graphite,
10% PTFE
30% PTFE 15%
graphite
Density
(DIN EN ISO 1183)
Mechanical properties
Modulus of elasticity (tensile test)
(DIN EN ISO 527-2)
Tensile strength
(DIN EN ISO 527-2)
Tensile strength at yield
(DIN EN ISO 527-2)
Elongation at yield
(DIN EN ISO 527-2)
Elongation at break
(DIN EN ISO 527-2)
Modulus of elasticity (flexural test)
(DIN EN ISO 178)
Flexural strength
(DIN EN ISO 178)
Compression modulus
(EN ISO 604)
Compressive strength (1% / 2%)
(EN ISO 604)
Impact strength (Charpy)
(DIN EN ISO 179-1eU)
Notched impact strength (Charpy)
(DIN EN ISO 179-1eA)
Ball intendation hardness
(ISO 2039-1)
Thermal properties
Glass transition temperature
(DIN 53765)
Melting temperature
(DIN 53765)
Service temperature,
short term
Service temperature,
long term
Thermal expansion (CLTE),
23 – 60 °C (DIN EN ISO 11359-1;2)
Thermal expansion (CLTE),
23 – 100 °C (DIN EN ISO 11359-1;2)
Specific heat
(ISO 22007-4:2008)
Thermal conductivity
(ISO 22007-4:2008)
Electrical properties
Surface resistance
(DIN IEC 60093)
Miscellaneous data
Water absorption 24h / 96h (23 °C)
(DIN EN ISO 62)
Resistance
to hot water / bases
Resistance to weathering
Flammability (UL94)
(DIN IEC 60695-11-10;)
[g / cm³]
[MPa]
[MPa]
[MPa]
[%]
[%]
[MPa]
[MPa]
[MPa]
[MPa]
[kJ / m²]
[kJ / m²]
[MPa]
[°C]
[°C]
[°C]
[°C]
[10 -5 K -1 ]
[10 -5 K -1 ]
[J / (g*K)]
[W/(m*K)]
[Ω]
[%]
1.46 1.34 1.42 1.57 1.67 1.48 1.34 1.51 1.38 1.45
5,900 4,000 4,000 4,340 4,000 3,700 4,400
135 116 97 65 82 77 153 82 118 101
135
7 9.0 2.8 2.2 2.8 2.9 7.4 4.1 4.5 3.7
6,200 3,448 4,000 4,330 4,000 3,600 4,300
210 150 88 126 120 209 122 177 145
4,000 1,880 4,000 1,713 1,900
556 210 180 204 227 400 211 486 300
87 75.8 35.1 16.5 29.6 25.8 67.6 – 87.9 20.6
5.6 3.3 4.8 3.6 2.8 3.9 – – 9.3 1.6
228
280 368 (a) 330 (a) 330 (a) 330 (a) 330 (a) 330 (a) 330 (a) 370 (a) 370 (a)
n.a.
270
250 – – – – – – – – –
1.04 1.13 1.04 0.925
0.60 (c) 0.22 (b) 0.53 (b) 0.22 (b) 0.22 (b)
10 17 (d) 10 16 10 7 10 3 10 15 10 16 10 15
–
V0 V0 V0 V0 V0 V0 V0 V0 V0 V0
Data generated directly after machining (standard
climate Germany). For polyamides the values strongly
depend on the humidity content.
Test specimen to DIN EN ISO 527-2
+ good resistance
(+) limited resistance
– poor resistance (depending on concen -
tration, time and temperature)
n.b. not broken
n.a. not applicable
(a) Glass transition temperature
testing according to DIN EN ISO 11357
(b) Thermal conductivity testing according to ISO 8302
(c) Thermal conductivity testing according to ASTM E1530
(d) Surface resistance testing according to ASTM D 257
96