CLM HD8 - Projector Central

More documents

Recommendations

Info

11. Lamp menu 11.5 Status and run time overview lamps Overview 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Lamp and press ENTER. 3. Use the ▲ or ▼ key to select Overview and press ENTER. The status and the run time for each lamp are displayed. Image 11-12 Image 11-13 Image 11-11 11.6 Lamp mode What can be done? In 4 lamps mode, the projector will always ignite all 4 lamps. In 2 lamps mode, the projector will always ignite lamp 1 & 3 or 2 & 4 depending on the current run time. It will always use those with the lowest run time. In 1lampmode, the projector will always ignite lamp 3 or 4, depending on the current run time. It will always use the lamp with the lowest run time. How to change the lamp mode 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Lamp and press ENTER. 3. Use the ▲ or ▼ key to select Lamp mode and press ENTER. The Lamp mode selection menu is displayed. 4. Use the ▲ or ▼ key to select the desired lamp mode and press ENTER. Image 11-15 Image 11-16 Image 11-14 114 R59770057 CLM HD8 15/03/2010
12. Alignment menu 12. ALIGNMENT MENU About this chapter This chapter describes the alignment of the projector once the physical installation is finished. Via the software, the image will be perfectly aligned on the screen. Overview • Overview flow • Orientation • Lens adjustment • Side keystone • Blanking • Intensity • Gamma • Internal pattern • Color space • White peaking • ScenergiX 12.1 Overview flow Overview Level 1 Level 2 Level 3 Alignment Orientation Front Table Front Ceiling Rear Table Rear Ceiling Lens Zoom/Focus Shift Side keystone Blanking Top Bottom Left Right Reset Intensity Gamma Internal patterns Checker board Color bars Convergence Focus Full screen black Full screen blue R59770057 CLM HD8 15/03/2010 115
Page 1 and 2:
CLM HD8 User guide R9050130 R905013
Page 3 and 4:
Changes Barco provides this manual
Page 5 and 6:
Table of contents TABLE OF CONTENTS
Page 7 and 8:
Table of contents 12.8 Internal pat
Page 9 and 10:
1. Safety 1. SAFETY About this chap
Page 11 and 12:
1. Safety • Mercury Vapor Warning
Page 13 and 14:
1. Safety 1.4 Important warnings co
Page 15 and 16:
2. General 2. GENERAL About this ch
Page 17 and 18:
2. General Image 2-2 5. Remove the
Page 19 and 20:
2. General Positioning the projecto
Page 21 and 22:
2. General 2.5 Projector air inlets
Page 23 and 24:
3. Physical installation 3. PHYSICA
Page 25 and 26:
3. Physical installation 3.1.2 RCU
Page 27 and 28:
3. Physical installation a b c d e
Page 29 and 30:
3. Physical installation When this
Page 31 and 32:
3. Physical installation Image 3-16
Page 33 and 34:
3. Physical installation 3.5 Alignm
Page 35 and 36:
4. Stacking CLM projectors 4. STACK
Page 37 and 38:
4. Stacking CLM projectors D A B C
Page 39 and 40:
5. Connections 5. CONNECTIONS About
Page 41 and 42:
5. Connections max. 3 lamps on 4 la
Page 43 and 44:
5. Connections 5.3 Communication co
Page 45 and 46:
5. Connections RS232 An Electronic
Page 47 and 48:
6. Getting started 6. GETTING START
Page 49 and 50:
6. Getting started Ind. Key name De
Page 51 and 52:
9 0 3 4 6. Getting started Switchin
Page 53 and 54:
6. Getting started 3. When finished
Page 55 and 56:
6. Getting started When no digit is
Page 57 and 58:
6. Getting started Common Address E
Page 59 and 60:
7. START UP OF THE ADJUSTMENT MODE
Page 61 and 62:
7. Start up of the adjustment mode
Page 63 and 64:
8. Input menu 8. INPUT MENU Overvie
Page 65 and 66:
8. Input menu Input module Indicati
Page 67 and 68: 8. Input menu Genlock off Genlock o
Page 69 and 70: 8. Input menu When native resolutio
Page 71 and 72: 8. Input menu The Input menu is dis
Page 73 and 74: 9. Image menu 9. IMAGE MENU Overvie
Page 75 and 76: 9. Image menu 9.3.1 Contrast About
Page 77 and 78: 9. Image menu 9.3.4 Tint (hue) Abou
Page 79 and 80: 9. Image menu Image 9-25 Image 9-24
Page 81 and 82: 9. Image menu Image 9-35 9.3.8.2 Se
Page 83 and 84: 9. Image menu One can conclude here
Page 85 and 86: 9. Image menu The projected image s
Page 87 and 88: 9. Image menu Use the or key to adj
Page 91 and 92: 9. Image menu Auto Off Detects for
Page 93 and 94: 9. Image menu 9.6.2 Manual Load fil
Page 97 and 98: 9. Image menu 2. Use the ▲ or ▼
Page 99 and 100: 10. Layout menu 10. LAYOUT MENU Ove
Page 101 and 102: 10. Layout menu Image 10-7 Size adj
Page 103 and 104: 10. Layout menu Image 10-16 [ ] = n
Page 105 and 106: 10. Layout menu Image 10-24 Positio
Page 107 and 108: 10. Layout menu Image 10-33 Size PI
Page 109 and 110: 10. Layout menu A Save window opens
Page 111 and 112: 10. Layout menu 10.4.2 Rename a lay
Page 113 and 114: 10. Layout menu Image 10-63 Image 1
Page 115 and 116: 11. Lamp menu 11. LAMP MENU Overvie
Page 117: 11. Lamp menu Image 11-7 About over
Page 121 and 122: 12. Alignment menu For more informa
Page 123 and 124: 12. Alignment menu 12.5 Blanking Wh
Page 125 and 126: 12. Alignment menu 3. Use the ▲ o
Page 127 and 128: 12. Alignment menu Image 12-31 When
Page 129 and 130: 12. Alignment menu 12.11.2 Preparat
Page 131 and 132: 12. Alignment menu Image 12-47 How
Page 133 and 134: 12. Alignment menu How to set for t
Page 135 and 136: 12. Alignment menu Image 12-68 Widt
Page 137 and 138: 12. Alignment menu Image 12-74 Imag
Page 139 and 140: 13. Projector control 13. PROJECTOR
Page 141 and 142: 13. Projector control Image 13-4 13
Page 143 and 144: 13. Projector control Image 13-14 I
Page 145 and 146: 13. Projector control [ON] = DHCP i
Page 147 and 148: 13. Projector control Image 13-31 I
Page 149 and 150: 13. Projector control Image 13-41 1
Page 151 and 152: 13. Projector control About channel
Page 153 and 154: 13. Projector control The allocated
Page 155 and 156: 13. Projector control 3. Use the
Page 157 and 158: 14. Service menu 14. SERVICE MENU A
Page 159 and 160: 14. Service menu 14.3 Diagnosis Wha
Page 161 and 162: 14. Service menu 14.3.4 I²C diagno
Page 163 and 164: 14. Service menu Image 14-27 Use th
Page 165 and 166: 14. Service menu 2. Use the ▲ or
Page 167 and 168: 14. Service menu When the projector
Page 169 and 170:
14. Service menu 4. Use the ▲ or
Page 171 and 172:
15. Maintenance 15. MAINTENANCE Abo
Page 173 and 174:
16. Servicing 16. SERVICING About t
Page 175 and 176:
16. Servicing A B C Image 16-2 Fron
Page 177 and 178:
16. Servicing A Image 16-5 Slide ou
Page 179 and 180:
16. Servicing Image 16-9 Take out t
Page 181 and 182:
16. Servicing CAUTION: Ensure that
Page 183 and 184:
16. Servicing 10.Close the main lid
Page 185 and 186:
17. PROJECTOR COVERS, REMOVAL AND I
Page 187 and 188:
17. Projector covers, removal and i
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
A. Dimensions A. DIMENSIONS Overvie
Page 197 and 198:
B. Standard Source Files B. STANDAR
Page 199 and 200:
C. DMX Chart C. DMX CHART Overview
Page 201 and 202:
C. DMX Chart Chan-Functionel Type R
Page 203 and 204:
D. Specifications D. SPECIFICATIONS
Page 205 and 206:
D. Specifications D.2 Specification
Page 207 and 208:
D. Specifications D.4 Specification
Page 209 and 210:
E. Troubleshooting E. TROUBLESHOOTI
Page 211 and 212:
E. Troubleshooting Error code Descr
Page 213 and 214:
E. Troubleshooting Error code Descr
Page 215 and 216:
F. MOUNTING OPTIONAL CARRY HANDLE F
Page 217 and 218:
F. Mounting optional Carry handle I
Page 219 and 220:
F. Mounting optional Carry handle 1
Page 221 and 222:
G. Order info G. ORDER INFO G.1 Spa
Page 223 and 224:
Glossary GLOSSARY 2:2 pull-down The
Page 225 and 226:
Index INDEX A Adjustment 48-50 Quic
Page 227 and 228:
Index Identification 113 Lamp mode
Page 229 and 230:
Index Source timings 83 Specificati
Page 231:
Revision Sheet To: Barco nv Events/
show all

CLM HD8 - Projector Central

Create successful ePaper yourself

Delete template?

Save as template?