CLIOwin 7 PCI User's Manual - Audiomatica

More documents

Recommendations

Info

Amplifier & SwitchBox Model 2,3 and 4. If QC Box Select is selected the hardware setting of the QC Box determines directly the Impedance Mode (please refer to chap. 5.5.1) 10.2.4 MLS & LOG CHIRP POST-PROCESSING TOOLS Loads an MLS & LOG CHIRP process. Figure 10.3 Saves an MLS & LOG CHIRP process. Adds a data value or compatible file to the current measurement. Subtracts a data value or compatible file to the current measurement. Multiplies the current measurement by a data value or compatible file. Divides the current measurement by a data value or compatible file. Shifts the current measurement by a dB value. Multiplies the current measurement by complex frequency. Divides the current measurement by complex frequency. Uses a reference measurement file taken at speaker terminals to calculate 1m sensitivity in dBSPL/W. The reference file should have dBV Y units while the one in memory should be in dBSPL. Process the current measurement with an octave band filter. It is possible to input the mid-band value and the filter bandwidth. Temporally shifts the current measurement by a ms value. Affects phase response. Merges the current measurement with the part below the selected transition frequency of a selected compatible file. 112 Chapter 10 - MLS
Combines the actual measurement and the selected file to obtain a constant current impedance measurement. Both files should be in dBV. Combines the actual measurement and the selected file to obtain a constant voltage impedance measurement. Both files should be in dBV. 10.3 IMPULSE RESPONSE CONTROL PANEL Figure 10.4 10.3.1 TOOLBAR BUTTONS The following toolbar buttons differ from frequency domain control panel: Displays Impulse Response. Displays Step Response. Displays Schroeder Decay. Displays Energy Time Curve (ETC). Also the following buttons inside the measurement area are particular to this control panel. See Chapter 6 for other general information. Selects the starting point of the measurement window. Selects the end point of the measurement window. Restores the default state of the measurement window thus selecting all the acquired points for analysis. Stores and display an overlay curve Activates marker A and B Chapter 10 - MLS 113
Page 1 and 2:
ELECTRICAL & ACOUSTICAL TESTS User'
Page 3 and 4:
CONTENTS 1 INTRODUCTION ...........
Page 5 and 6:
7.10 SIGNAL FILES .................
Page 7:
14.1 INTRODUCTION .................
Page 10 and 11:
AUDIOMATICA’S WARRANTY Audiomatic
Page 12 and 13:
12 Chapter 1 - Introduction
Page 14 and 15:
2.1 THE PB-4281 PC BOARD AND SC-01
Page 16 and 17:
2.2.3 THE MIC-01 (OR MIC-02) FREQUE
Page 18 and 19:
2.4 THE QCBOX MODEL 4 AMPLIFIER & S
Page 20 and 21:
2) 2 x Stereo mini jack to two RCA
Page 22 and 23:
3.3 HARDWARE REGISTRATION WITH WIND
Page 24 and 25:
3.3.2 HARDWARE REGISTRATION UNDER W
Page 26 and 27:
3.3.3 HARDWARE REGISTRATION UNDER W
Page 28 and 29:
Figure 3.21 Let's now verify that t
Page 30 and 31:
3.4 SOFTWARE INSTALLATION This para
Page 32 and 33:
3.6 RUNNING CLIOWIN FOR THE FIRST T
Page 34 and 35:
3.7.1 CALIBRATION VALIDATION Figure
Page 36 and 37:
3.9 TROUBLESHOOTING CLIO INSTALLATI
Page 38 and 39:
4.3 CLIOWIN DESKTOP The CLIOwin des
Page 40 and 41:
4.5 HARDWARE CONTROLS TOOLBAR 4.5.1
Page 42 and 43:
4.5.4 MICROPHONE CONTROL Switches C
Page 44 and 45:
4.6.2 CONTROLLING A TURNTABLE Fig.4
Page 46 and 47:
4.7.2 ANALYSIS MENU The Analysis me
Page 48 and 49:
Fig. 4.16 Sinusoidal Submenu Fig. 4
Page 50 and 51:
4.7.3 CONTROLS MENU The Controls Me
Page 52 and 53:
4.8 BASIC CONNECTIONS In order to c
Page 54 and 55:
4.8.3 CONNECTING THE CLIOQC AMPLIFI
Page 56 and 57:
T&S parameters data files. Wow&Flut
Page 58 and 59:
Invokes the Autosave Settings dialo
Page 60 and 61:
5.3.4 PRINTING Enters the Notes dia
Page 62 and 63: customize up to 6 different color s
Page 64 and 65: 5.7.1 SAVING MEASUREMENT SETTINGS M
Page 66 and 67: 6.3 BUTTONS AND CHECKBOXES Moves (s
Page 68 and 69: 6.6 THE MLS TIME DOMAIN DISPLAY Whe
Page 70 and 71: The following figure shows a 1031.2
Page 72 and 73: 7.4 MULTITONES It is possible to ge
Page 74 and 75: 7.6 MLS It is possible to generate
Page 76 and 77: 7.8 The following figure shows a 20
Page 78 and 79: The following figure shows the same
Page 80 and 81: For comparison with Pink noises the
Page 82 and 83: The following figure shows a msampl
Page 84 and 85: 84 Chapter 7 - Signal Generator
Page 86 and 87: 8.2.1 TOOLBAR BUTTONS Starts the me
Page 88 and 89: This is substantially the measureme
Page 90 and 91: With the Multi-meter running, fit t
Page 92 and 93: 8.6 INTERACTION BETWEEN THE MULTI-M
Page 94 and 95: 9.2.1 TOOLBAR BUTTONS, DROP DOWN LI
Page 96 and 97: 9.4 FFT SETTINGS DIALOG Fig. 9.2 Th
Page 98 and 99: A better approach is to center the
Page 100 and 101: it is necessary to remove the fligh
Page 102 and 103: 80.0 CLIO dBSPL 70.0 60.0 50.0 40.0
Page 104 and 105: 9.10 “LIVE” TRANSFER FUNCTION A
Page 106 and 107: Another factor of maximum importanc
Page 108 and 109: The last obstacle you may find whil
Page 110 and 111: 10.2.1 TOOLBAR BUTTONS Starts an ML
Page 114 and 115: 10.4 MEASURING FREQUENCY RESPONSE I
Page 116 and 117: 150.0 CLIO 180.0 150.0 CLIO 180.0 O
Page 118 and 119: speaker we are testing is a gloriou
Page 120 and 121: 10.4.4 PHASE & GROUP DELAY We used
Page 122 and 123: etween true phase, as in Fig.10.22,
Page 124 and 125: 10.5 OTHER TIME DOMAIN INFORMATION
Page 126 and 127: utton. Any process you execute can
Page 128 and 129: 10.7 MLS Vs. LOG CHIRP As anticipat
Page 130 and 131: 10.8 RELATED MENUS The dual domain
Page 132 and 133: Display fifth harmonic distortion,
Page 134 and 135: Gating (Acquisition) Settings Gated
Page 136 and 137: 11.3 A BRIEF DESCRIPTION ON SETTING
Page 138 and 139: 11.3.3 GATING Enabling Gating allow
Page 140 and 141: 11.4 DISTORTION AND SETTINGS Sinuso
Page 142 and 143: Finally Fig.11.12 shows the distort
Page 144 and 145: 12.2 WATERFALL AND DIRECTIVITY CONT
Page 146 and 147: 12.3.2 WATERFALL OPERATION As alrea
Page 148 and 149: Figure 12.5 One powerful way to ins
Page 150 and 151: 12.5 DIRECTIVITY SPECIFIC CONTROLS
Page 152 and 153: 12.6 MEASURING AND REPRESENTING LOU
Page 154 and 155: 12.6.4 REPRESENTING POLAR DATA To r
Page 156 and 157: 156 Chapter 12 - Waterfall and Dire
Page 158 and 159: If you are a novice in using CLIO,
Page 160 and 161: life harder even if more interestin
Page 162 and 163:
13.4 I SENSE This requires Audiomat
Page 164 and 165:
0.0 CLIO 180.0 dBV Deg -10.0 108.0
Page 166 and 167:
CLIO INPUT A INPUT B OUTPUT A OUTPU
Page 168 and 169:
13.7 THIELE & SMALL PARAMETERS 13.7
Page 170 and 171:
L 1kHz L 10kHz Inductance at 1kHz I
Page 172 and 173:
We can now save our complete result
Page 174 and 175:
The graphs refers to a linearity me
Page 176 and 177:
DIN measures Intermodulation distor
Page 178 and 179:
15.2.1 TOOLBAR BUTTONS AND DROP DOW
Page 180 and 181:
15.3 ACOUSTICAL PARAMETERS SETTINGS
Page 182 and 183:
RTU [s]. Reverberation time evaluat
Page 184 and 185:
184 Chapter 15 - Acoustical Paramet
Page 186 and 187:
16.2.1 TOOLBAR BUTTONS AND DROP DOW
Page 188 and 189:
16.3 Leq SETTINGS Time resolution S
Page 190 and 191:
17.3 FEATURES Figure 17.2 Aside a s
Page 192 and 193:
192 Chapter 17 - Wow & Flutter
Page 194 and 195:
[20] D. Clarke, “Precision Measur
Page 196:
196 Norms
show all

CLIOwin 7 PCI User's Manual - Audiomatica

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?