b-1 tender form - Maharashtra Industrial Development Corporation
b-1 tender form - Maharashtra Industrial Development Corporation
b-1 tender form - Maharashtra Industrial Development Corporation
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
70<br />
MAHARASHTRA INDUSTRIAL DEVELOPMENT CORPORATION<br />
( A Government of <strong>Maharashtra</strong> Undertaking.)<br />
Item Wise Specification<br />
Name of Work : M&R to W/S/S/ to Lote Indl.Area..<br />
Replacement of damaged shutters of inspection chambers, Providing Paving blocks to pump house,<br />
Providing Cain at pure water pump house at WTP Lote and Ram, Shed & Collapsible shutters at<br />
Jackwell Wallope.<br />
Item No 1: Providing and fixing anodised aluminium fixed glazing shutter with outer frame made<br />
up of bottom section as per requirement including 6 mm thick clear sheet glass fixed by means of<br />
triangular clips or flush glazing system, with rubber gaskets as approved by the dept., including<br />
finishing, cleaning, polishing the aluminium section with petrol and / or other agents as specified by<br />
the manufacturer etc. complete.<br />
a) Aluminium section used.<br />
b) 6 mm thick sheet glass used<br />
25.1 General : The item pertains to providing and fixing anodized aluminium fixed glazing shutter<br />
con<strong>form</strong>ing to IS: 1943.<br />
25.2 Material : The aluminium sections for door shall be as described below :<br />
Outer Frame : 100 x 45 mm tube section AL-HK 15 section weighing<br />
approx. 1.547 kg/m<br />
Shutter Bottom & Top : 45 x 100 mm tube section<br />
Shutter Vertical : 40 x 100 mm tube section<br />
Sheet Glass : 6 mm thick clear float glass con<strong>form</strong>ing to IS:2835- 1991. Rubber gasket, tower bolts,<br />
decorative type handles, steel latches and other fixtures and fastenings shall be approved by the<br />
Engineer-incharge.<br />
25.3 Fabrication & Fixing :<br />
25.3.1 Fixed Glazing Shutter :<br />
1. Frames : Frames shall be square and flat, the corners of the frame being fabricated to a true right<br />
angle. Both the fixed and opening frames shall be constructed of sections, which have been cut to<br />
length, mitred and connected at the corners.<br />
25.3.2 Openeable Shutter:<br />
1. Frames : Frames shall be square and flat, the corners of the frame being fabricated to a true right<br />
angle. Both the fixed and opening frames shall be constructed of sections, which have been cut to<br />
length, mitred and connected at the corners.<br />
2. Side-hung Shutters : For fixing aluminium alloy hinges, slots shall be cut in the fixed frame and the<br />
hinges inserted inside and may be riveted to the frame. The hinges shall normally be of the projecting<br />
type 67 mm wide. The aluminium alloy for cast hinges shall con<strong>form</strong> to IS designation A-5 M of IS:617<br />
latest edition. Specification for aluminium and aluminium alloy ingots and castings for general<br />
engineering purposes (revised) and for extruded section of hinges to IS designation HE10-WP or<br />
HE30-WP of IS:733. Specification for wrought aluminium and aluminium alloys HR30. Irrespective of<br />
hinges being anodised or not, the aluminium alloy pins shall be anodised to a minimum film thickness<br />
of 0.025 mm and shall be sealed with oil, wax or lanolin. Non-projecting types of hinges may also be<br />
used, where agreed to between the purchaser and the supplier.<br />
Friction hinges may be provided for side-hung shutter windows, in which case peg stay as<br />
mentioned below may not be required. The working principle of the friction hinge is illustrated. The<br />
handle for side hung shutters shall be of cast aluminium con<strong>form</strong>ing to IS designation A-5-M of<br />
IS:617. Specification for aluminium and aluminium alloy ingots and castings for general engineering<br />
Contractor.<br />
Executive Engineer(E&M).