AutoVu Handbook 5.1 SR2 - Genetec

More documents

Recommendations

Info

Mobile installation procedure This cable design allows you to cut the pigtail end of the Sharp cable to fit your specific installation. However, if you cut the cable, make sure to leave some slack for maintenance purposes. IMPORTANT Read full crimp instructions at www.tycoelectronics.com for RJ45 part number 5-569552-3. Return to diagram, click here. 1 Strip the SharpX camera cable to expose the CAT5e cable (and other wires) inside. Trim the polyester fill threads and aluminum foil as needed. Before After CAT5e cable 1 Strip the CAT5e cable you exposed in Step 1. Make sure not to nick or cut the insulation of the interior wires. genetec.com | AutoVu Handbook 5.1 SR2 | Download latest version 100 EN.400.003-V5.1.C2(1)
Mobile installation procedure 2 Crimp the wires according to the TIA/EIA-568-B.1-2001 specification, using the T568B conductor arrangement. Remember that the cable and connector are shielded, so you need to fold the foil shield so it has contact with the RJ45’s metal shell. 3 After you’ve attached the RJ45 connector, plug the CAT5e cable into the into the first Data Link port. Connect RJ45 here 4 Repeat these steps for the other SharpX camera as needed. Step D: Connect the SharpX power cable to the LPR Processing Unit This section shows you how to connect the SharpX power cable to the LPR Processing Unit. NOTE SharpX connectors use push-in tension clamps to secure the wires. Return to diagram, click here. Before you begin: You’ll need a 2.5 mm flat head screwdriver. 1 Attach the 5-pole connector to the camera port, then tighten the securing screws. Make sure to tighten the securing screws. genetec.com | AutoVu Handbook 5.1 SR2 | Download latest version 101 EN.400.003-V5.1.C2(1)
Page 1 and 2:
AutoVu Handbook 5.1 SR2 Click here
Page 3 and 4:
Product documentation Security Cent
Page 5 and 6:
Contents Product documentation . .
Page 7 and 8:
| Link a camera to an LPR unit . .
Page 9 and 10:
| Fixed installation procedure . .
Page 11 and 12:
| Chapter 10: Upgrading AutoVu Upgr
Page 13 and 14:
| LPR Unit entity . . . . . . . . .
Page 15 and 16:
| Hotlists . . . . . . . . . . . .
Page 17 and 18:
About this guide This guide provide
Page 19 and 20:
1 Introducing AutoVu This section d
Page 21 and 22:
What is AutoVu? The following diagr
Page 23 and 24:
AutoVu hardware components • Auto
Page 25 and 26:
AutoVu software components What is
Page 27 and 28:
2 AutoVu software interface tours T
Page 29 and 30:
Security Center Config Tool interfa
Page 31 and 32:
Patroller Config Tool interface tou
Page 33 and 34:
Patroller Config Tool interface tou
Page 35 and 36:
Sharp Admin interface tour Log off
Page 37 and 38:
Sharp Admin interface tour Benefits
Page 39 and 40:
Where to find the most common tasks
Page 41 and 42:
About the fixed deployment process
Page 43 and 44:
Phase 2: AutoVu software installati
Page 45 and 46:
Phase 4: Configure LPR Manager for
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Phase 5: Configure LPR unit 7 (Opti
Page 55 and 56:
Phase 6: Configure hotlists Phase 6
Page 57 and 58:
Phase 6: Configure hotlists 2 Send
Page 59 and 60:
About the mobile deployment process
Page 61 and 62:
Phase 2: AutoVu software installati
Page 63 and 64:
Page 65 and 66:
Page 67 and 68: Phase 4: Configure LPR Manager for
Page 69 and 70: Phase 5: Configure hotlists Phase 5
Page 71 and 72: Phase 5: Configure hotlists 1 Send
Page 73 and 74: Phase 5: Configure hotlists 1 Log o
Page 75 and 76: Phase 6: Configure Patroller unit s
Page 77 and 78: Phase 7: Configure Patroller Config
Page 79 and 80: Phase 7: Configure Patroller NOTE I
Page 81 and 82: Hardware specifications and system
Page 83 and 84: Safety precautions • Make sure ca
Page 85 and 86: Fixed installation example Fixed in
Page 87 and 88: Fixed installation guidelines Fixed
Page 89 and 90: Fixed installation guidelines Sharp
Page 91 and 92: Fixed installation procedure Fixed
Page 93 and 94: Fixed installation procedure Step 4
Page 95 and 96: 7 Installing mobile AutoVu hardware
Page 97 and 98: Mobile installation examples for Sh
Page 103 and 104: Mobile installation procedure for S
Page 113 and 114: Mobile installation procedure Mobil
Page 115 and 116: Mobile installation procedure NOTE
Page 117: Mobile installation procedure 2 Str
Page 121 and 122: Mobile installation procedure Retur
Page 123 and 124: 9 Installing Patroller This section
Page 125 and 126: System requirements Item Wireless c
Page 127 and 128: Before you install Before you insta
Page 129 and 130: Installation overview Installation
Page 131 and 132: Installing AutoVu Patroller NOTE Mi
Page 133 and 134: Upgrading Patroller and Sharp units
Page 139 and 140: Upgrading Patroller Upgrade overvie
Page 141 and 142: Upgrade FAQ for Patroller users Upg
Page 143 and 144: About advanced configuration About
Page 145 and 146: Configure the Sharp for an FTP conn
Page 147 and 148: Using a SharpX - Multi system Using
Page 149 and 150: Configuring Sharp Admin security Co
Page 151 and 152: Configuring Sharp Admin security 7
Page 153 and 154: Configuring Sharp Admin security Co
Page 155 and 156: Connecting Sharp units to Patroller
Page 157 and 158: Connecting Sharp units to Patroller
Page 159 and 160: Setting up USB support Set Root fol
Page 161 and 162: Setting up USB support 4 Open USB_T
Page 163 and 164: Using a SharpX system with multiple
Page 165 and 166: Install the GPS driver 8 Click Fini
Page 167 and 168: Enabling privacy on individual hotl
Page 169 and 170:
Moving Patroller or LPR units betwe
Page 171 and 172:
12 Config Tool reference This secti
Page 173 and 174:
Common configuration tabs Standard
Page 175 and 176:
Common configuration tabs Custom fi
Page 177 and 178:
Common configuration tabs map in Se
Page 179 and 180:
Hotlist entity Properties The Prope
Page 181 and 182:
Hotlist entity • Fixed length. Th
Page 183 and 184:
Hotlist entity • Limit the number
Page 185 and 186:
LPR Unit entity LPR Unit entity An
Page 187 and 188:
Patroller entity Patroller entity A
Page 189 and 190:
Patroller entity • Machine name.
Page 191 and 192:
User entity Properties The Properti
Page 193 and 194:
User entity User level Security Cen
Page 195 and 196:
User entity Workspace The Workspace
Page 197 and 198:
User group entity User group entity
Page 199 and 200:
User group entity Security The Secu
Page 201 and 202:
LPR Manager role LPR Manager role T
Page 203 and 204:
LPR Manager role the username and p
Page 205 and 206:
LPR Manager role • Root folder. T
Page 207 and 208:
LPR Manager role • Accept Non Enc
Page 209 and 210:
LPR Manager role • Email componen
Page 211 and 212:
LPR Manager role XML export The XML
Page 213 and 214:
LPR Manager role XML import The XML
Page 215 and 216:
LPR administration task LPR adminis
Page 217 and 218:
LPR administration task • "Update
Page 219 and 220:
LPR administration task Hotlist The
Page 221 and 222:
LPR administration task NOTE Before
Page 223 and 224:
General General The General setting
Page 225 and 226:
Security Center Security Center Liv
Page 227 and 228:
Security Center Offload Offloading
Page 229 and 230:
Plugin Plugin The Plugin page is wh
Page 231 and 232:
Hits Hits The Hits page allows you
Page 233 and 234:
Hits Setting Use shared permit Bypa
Page 235 and 236:
Navigation Navigation The Navigatio
Page 237 and 238:
Navigation Setting Read when moving
Page 239 and 240:
User interface Setting Start applic
Page 241 and 242:
Advanced Mobile patroller hit Setti
Page 243 and 244:
Status Status The Status page displ
Page 245 and 246:
Status Actions Displays several act
Page 247 and 248:
Configuration Configuration The Con
Page 249 and 250:
Configuration Setting Show settings
Page 251 and 252:
Configuration • Interface 3 and I
Page 253 and 254:
Configuration Setting Description P
Page 255 and 256:
Live feed Live feed The Live feeds
Page 257 and 258:
Diagnostics Diagnostics Search fiel
Page 259 and 260:
A SharpX LED status reference This
Page 261 and 262:
LED status on the LPR Processing Un
Page 263 and 264:
LED status on the SharpX camera uni
Page 265 and 266:
AutoVu Sharp parts AutoVu Sharp par
Page 267 and 268:
AutoVu Sharp parts Understanding th
Page 269 and 270:
AutoVu SharpX parts a. For more inf
Page 271 and 272:
Access troubleshooter Access troubl
Page 273 and 274:
Area activities Area activities Are
Page 275 and 276:
camera camera Camera events camera
Page 277 and 278:
Credential activities Credential ac
Page 279 and 280:
door side door side Door troublesho
Page 281 and 282:
free access free access free exit G
Page 283 and 284:
Health history Health history Healt
Page 285 and 286:
interface module interface module i
Page 287 and 288:
license plate inventory license pla
Page 289 and 290:
map link map link Map mode map obje
Page 291 and 292:
Move unit Move unit MPEG-4 multicas
Page 293 and 294:
partition partition partition manag
Page 295 and 296:
PlateReaderServer PlateReaderServer
Page 297 and 298:
ecording state recording state redi
Page 299 and 300:
selector selector server Server Adm
Page 301 and 302:
strict antipassback strict antipass
Page 303 and 304:
Transmission Control Protocol Trans
Page 305 and 306:
vehicle identification number vehic
Page 307 and 308:
Wiegand Wiegand An electrical inter
Page 309 and 310:
Index | G configuring basic propert
Page 311 and 312:
Index | R configuring sound managem
show all

AutoVu Handbook 5.1 SR2 - Genetec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?