equipment sourcebook - Loctite.ph

LOCTITE ® ZETA ® 7760 UV WAND SYSTEMS
Item Numbers: 98450 and 958239
The Loctite® ZETA® 7760 UV Wand Systems utilize a 200 watt high pressure mercury arc lamp with a universal power supply and
a liquid-filled light wand. These systems have the highest intensity output for a Loctite® brand wand system by a factor of 2. The
Loctite® ZETA® 7760 UV Wand Systems can be operated manually or in the timed mode and are capable of interfacing with a PLC
controlled circuit. Continuous lamp intensity monitoring is also available by selecting item 958239 and the required Light
Intensity Monitor item 891494. The light guides are also sold separately from the base units.
Light guide choices are highlighted below.
Features:
• Our highest output light intensity wand. Typical initial
Intensity is 16 to 20 W/cm 2
• Contains a high pressure mercury arc lamp
• 1,000 hours of expected UV lamp life with proper
handling and maintenance
• Manual or timed shutter light exposure, 0 to 99.9 seconds
• Hour meter for monitoring accumulated lamp life
• Self-test diagnostics displays message when a problem exists
Additional Features for Item 958239 when used in conjunction with 891494
• LED control display highlights relative intensity
changes in 10% increments
• Minimum required intensity can be programmed for a
warning or integrated to PLC for external alarm or
shutdown condition
Theory of Operation
When the unit is switched on, the proper electrical power is
immediately supplied to the lamp. It will take a few minutes for
the lamp to reach full power. The operator will manually
or automatically place the part under the end of the UV wand.
Curing will take place when the UV light is directed at the liquid
adhesive. Engaging the foot switch opens the shutter and UV
energy produced by the lamp is immediately transmitted
through the flexible light guide. The end of the wand can be
manually operated or mounted in a fixed position.
Light Guide Options – UV wands
Description
Dimensions
Item Numbers
Single Pole 2 Pole 3 Pole 4 Pole
Standard 1 5 mm x 1000 mm 983677 • • •
3 mm x 1000 mm N/A 983684 2 98596 2 98597 2
5 mm x 1500 mm 951681 • • •
Enhanced UVC 2 5 mm x 1000 mm 97326 • • •
3 mm x 1000 mm N/A 97328 2 98593 2 98594 2
5 mm x 1500 mm 98543 • • •
1. Enhanced UVC wands require optional filter kit (98598) to optimize tack-free
surface cure on the Loctite® ZETA® 7760. (sold separately)
2 Requires balancing adapter (951639) on initial setup.
• Multi-pole guides are only available with 3 mm diameter poles.
TECHNICAL SPECIFICATIONS
Item Numbers 98450 / 958239
Power Supply
90/265 VAC; 50/60 Hz input
Power Protection
4 A / 250 V fuse
Auxiliary Control Voltage
24 VDC
Lamp Life
Approximately 1,000 hours
Warm-Up Time
5 minutes
Main Fuse
5 A, 250 V
Dimensions
8.3" H x 11.5" W x 13.4" D
Weight
19.5 lbs.
Optimized Spectral Output Range
UVA, B, C
16 to 20 W/cm
Typical
(using 5 mm x 1,000 mm light guide)*
UV Output
Characteristics UV Spectral Range
250 to 410 nm
Primary Peak
365 nm
Parts Included
(1) Loctite ® ZETA ® 7760 UV Wand System
(1) Ultraviolet Protection Glasses (1) Power Cord
(1) UV Lamp (1) Foot Pedal (1) Manual
Replacement Parts
98451 – 200 watt HPMA UV Bulb
Additional Accessories Sold Separately
98048 –
Loctite ® ZETA ®
7021 Spot Radiometer
(See page 114)
891494 –
Loctite ® Light
Intensity Monitor –
for 958239 only
* Exact output measurement is dependent on the brand and calibration method
of the UV meter, and the condition and straightness of the light guide used.
LIGHT CURE Wand Systems
LOCTITE ® LIGHT INTENSITY MONITOR
Item Number: 891494
Power Supply
Main Fuse
Dimensions
Weight
Parts Included
TECHNICAL SPECIFICATIONS
90/265 VAC; 50/60 Hz input
1 A, 250 V
5.5" H x 6.1" W x 6.8" D
1 lbs.
(1) Intensity Monitor
(1) Sensor Input Cable
(1) Power Cord (1) Manual
For additional information and the full line of equipment, visit www.equipment.loctite.com.
107