equipment sourcebook - Loctite.ph
equipment sourcebook - Loctite.ph
equipment sourcebook - Loctite.ph
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
LOCTITE<br />
Heading ® HYSOL 175 MANUAL APPLICATOR<br />
– Epoxy & Urethane Adhesives<br />
Item Number: 98035<br />
The <strong>Loctite</strong>® Hysol 175 is an industrial grade, electrically heated, hand held, manual hot melt applicator. This unit comes with two<br />
plug-in thermostats for either EVA or polyamide adhesives. The dispense quantity and timing are manually controlled with the<br />
ergonomic trigger mechanism.<br />
Features:<br />
The complete source on <strong>Loctite</strong>® brand adhesives,<br />
• Includes two plug-in modules for dispensing both<br />
sealants,<br />
polyamide<br />
lubricants,<br />
and EVA<br />
coatings,<br />
hot melts<br />
dispensing and curing<br />
<strong>equipment</strong> • Lightweight, available well balanced, only from and ergonomically<br />
Henkel Corporation.<br />
designed for operator comfort and application control<br />
• Completely enclosed heater housing for maximum safety<br />
• Fast heat up time for virtually immediate use<br />
• Advanced electronic controller provides power saving mode,<br />
when not in use for long periods of time<br />
• Fixed precision thermostat (plug-in module)<br />
for consistent heating<br />
• Thermal fuse protection<br />
for additional safety<br />
Theory of Operation<br />
The dispense rate and<br />
timing are manually<br />
controlled with the<br />
trigger mechanism.<br />
TECHNICAL SPECIFICATIONS<br />
Required Voltage<br />
110/120 VAC; 50/60 Hz<br />
Utilities Power<br />
400 watts<br />
Nominal Stick Diameter<br />
1.75" Polyshot Sticks<br />
Size<br />
2.67" W x 12.25" L x 9.63" H<br />
Weight<br />
2.65 lbs.<br />
Power Cord Length 10 feet (120")<br />
Maximum Extension Cord<br />
65 feet<br />
Warm-Up Time<br />
5 to 7 minutes<br />
Dispense Power<br />
Manual<br />
Dispense Melt Rate<br />
6.6 lbs./hour<br />
Dispense Temperature 195°C or 215°C<br />
Applicator Adhesive Capacity<br />
0.125 lbs.<br />
Wire Cross-Section<br />
16 a.w.g. minimum<br />
Hot Melt Chemistry<br />
EVA and polyamide hot melt sticks<br />
Parts Included (1) Hysol 175 Applicator (1) Plug-In Module (215°C)<br />
(1) Plastic Stand (1) Standard Nozzle<br />
(1) Plug-In Module (195°C) (1) Manual<br />
Additional Information For Hot Melt Nozzles and Accessories, see page 49.<br />
DISPENSING Hand Held Hot<br />
Melt Applicators<br />
URETHANE DISPENSER<br />
LOCTITE ® HYSOL REACTIVE URETHANE CARTRIDGE DISPENSER<br />
Item Number: 98011<br />
The <strong>Loctite</strong>® Hysol Reactive Urethane Cartridge Dispenser is used to dispense reactive polyurethane hot melts from 300 ml<br />
cartridges. This electrically heated, pneumatic dispenser includes a pressure-regulating stand with optional vertical application<br />
stand and foot switch for hands-free application. To minimize<br />
cartridge change-over times, the <strong>Loctite</strong>® Cartridge Pre-Heater<br />
(item 98012) is recommended.<br />
Required<br />
Features:<br />
Utilities<br />
Voltage<br />
Power<br />
TECHNICAL SPECIFICATIONS<br />
120 VAC; 60 Hz; single <strong>ph</strong>ase<br />
400 watts<br />
• Lightweight, well balanced, and ergonomically<br />
designed for operator comfort and application control<br />
• Low actuation force to reduce finger fatigue<br />
• Electronic temperature control<br />
• Rugged molded thermoset plastic housing for<br />
“cool to the touch” operation up to 250°F<br />
• Fixed precision temperature: 250°F (121°C)<br />
• Single cartridge loading<br />
• Direct nozzle cartridge mounting for<br />
quick cartridge changeover<br />
• Various nozzles for different dispense patterns<br />
Theory of Operation<br />
This unit is used in the manual<br />
mode, where the operator<br />
manually begins and<br />
terminates the pneumatic<br />
dispense cycle by a hand<br />
trigger. Flow control is<br />
achieved by adjusting the<br />
regulator supplied on the<br />
base of the unit.<br />
Air Input<br />
80 psi air, filtered to 40 micron<br />
Size<br />
3.1" W x 12.5" L x 10.3" H<br />
Weight<br />
3 lbs.<br />
Adhesive<br />
Dispenses 300 cc aluminum cartridge<br />
Air Output<br />
Maximum 90 psi<br />
Warm-Up Time<br />
7 to 10 minutes<br />
Dispense Power<br />
Air<br />
Dispense Melt Rate<br />
3.5 lbs./hour<br />
Dispense Temperature 121°C<br />
Applicator Adhesive<br />
Capacity<br />
0.125 lbs.<br />
Hot Melt Chemistry<br />
<strong>Loctite</strong> ® Hysol ® Reactive Urethane hot melts<br />
Parts Included<br />
(1) Hysol Reactive Urethane Cartridge Dispenser<br />
(1) Base with Regulator and Gauge (1) Wire Stand<br />
(1) 300 cc Cartridge Adapter (1) Nozzle with Cap<br />
(1) Heat Resistant Gloves (1) Cartridge Piercer<br />
(1) Tubing Assembly (1) Manual<br />
Additional Information For Hot Melt Nozzles and Accessories, see page 49.<br />
Additional Accessories Sold Separately<br />
98012 – <strong>Loctite</strong> ® Cartridge Pre-Heater<br />
For additional information and the full line of <strong>equipment</strong>, visit www.<strong>equipment</strong>.loctite.com.<br />
47