OPERATOR'S MANUAL - The Baker Company Blog

More documents

Recommendations

Info

366D000M 1/4/2011Airflow Monitor (AFM) Installation and Calibration: SterilGARD ® Free StandingVented to Room.(Note: This option will indicate a low intake velocity condition by monitoring the air volume throughthe exhaust filter.)Vented to Room1) Remove all items from shipping container and identify the following: Contents should includeAirgate with 1” [25.4mm] probe installed, Airflow Monitor (AFM) and Velcro Strip (If AFMwas not factory installed).2) Insert the 1” [25.4mm] long AFM probe into the shaft collar located on top of the airgate ifnot already complete. <strong>The</strong> probe has a long scratch mark on its side. Rotate the probe so themark is positioned to the left side of the shaft collar as shown in Detail A. This will orientatethe thermisters (glass beads) on the probe tip in a horizontal plane so it can properly sense theairflow. Fully insert the probe so the tip passes through the hole in the airgate approximately3/32” [2.38mm]. Tighten the retaining collar set screw carefully. Do not over tighten. (Makesure not to rotate the probe while tightening).3) Remove the #8-32 hardware already fastened to the two weldstuds on top of the cabinet.4) Next grasp the Airgate and carefully lower it onto the top seal panel locating the keyholecontour onto the far left weld stud as shown in Figure 1. Once in place slide the Airgate to thefar left until it stops. Route probe wiring behind front access panel and plug into AFM. Besure to tie up extra probe cord length in order to prevent interference with viewscreen.5) Next place the Exhaust Filter Protector on top of the unit locating the holes onto the two frontweldstuds and replace #8-32 hardware and tighten.6) Confirm that the cabinet and exhaust system airflow are at the proper set point.7) Check to make sure that the Air Flow Monitor probe is installed correctly.8) Reduce the cabinet blower speed to achieve 80fpm [0.406 m/sec.] through the cabinet accessopening.9) At this reduced intake, the yellow light to the Air Flow Monitor should come on, followed bythe flashing red light and audible alarm (if the slide switch for the audible alarm is in the ONposition) and the supply blower will shut off.10) If the red light is off, turn the ADJUST screw very, very slowly in a counterclockwise directionuntil the yellow light appears, followed in six seconds by the red light.11) Next, turn the ADJUST screw very slowly clockwise until the red light goes off. Wait 30seconds and turn the screw counterclockwise again until the yellow light appears, followed bythe red light. This sets the low alarm point for the Air Flow Monitor.101
366D000M 1/4/201112) Adjust the total airflow volume back to the operating level.EXHAUST FILTERPROTECTORAIRGATE#8-32HARDWARETOP OF CABINETDETAIL CAIRGATEORIENTATE SCRIBEMARK AS SHOWNAFM PROBEDETAIL AFigure 1: AFM installed in cabinet venting to room102
Page 1 and 2:
THE BAKER COMPANYOPERATOR’S MANUA
Page 3 and 4:
TABLE OF CONTENTSI - FUNCTION OF TH
Page 5 and 6:
Stand Assembly Leg Extension Proced
Page 7 and 8:
366D000M 1/4/2011Base Features• M
Page 9 and 10:
366D000M 1/4/2011has 7/16” [11.1m
Page 11 and 12:
366D000M 1/4/2011SpecificationsWeig
Page 13 and 14:
366D000M 1/4/2011Environmental Cond
Page 15 and 16:
366D000M 1/4/20111. Remove the stra
Page 17 and 18:
366D000M 1/4/2011The *FlexAIR is an
Page 19 and 20:
366D000M 1/4/2011Auxiliary Wiring O
Page 21 and 22:
366D000M 1/4/2011Auxiliary Cabinet
Page 23 and 24:
366D000M 1/4/2011• Ultraviolet (U
Page 25 and 26:
366D000M 1/4/2011The Double Proximi
Page 27 and 28:
366D000M 1/4/20113. Because opening
Page 29 and 30:
366D000M 1/4/2011cabinets, since th
Page 31 and 32:
366D000M 1/4/2011Recommended Decont
Page 33 and 34:
366D000M 1/4/2011Method to seal an
Page 35 and 36:
366D000M 1/4/20116. Tape sheeting t
Page 37 and 38:
366D000M 1/4/2011and allow the two
Page 39 and 40:
366D000M 1/4/2011IV - ONSITE CHECKS
Page 41 and 42:
366D000M 1/4/2011the front, lowerin
Page 43 and 44:
366D000M 1/4/2011A chemically conta
Page 45 and 46:
366D000M 1/4/2011at a time until th
Page 47 and 48:
366D000M 1/4/2011TroubleshootingIMP
Page 49 and 50:
366D000M 1/4/2011V - DISASSEMBLY IN
Page 51 and 52:
366D000M 1/4/2011Appendix46
Page 53 and 54:
366D000M 1/4/2011Baker Part NumberM
Page 55 and 56: 366D000M 1/4/2011SG403A-HE (With Ch
Page 57 and 58: 366D000M 1/4/2011SG403A-HE (With Hy
Page 59 and 60: 366D000M 1/4/2011SG503A-HE (Base Un
Page 63 and 64: 366D000M 1/4/2011SG503A-HE W/Canopy
Page 67 and 68: 366D000M 1/4/2011SG603A-HE (With Hy
Page 69 and 70: 366D000M 1/4/2011SG403A-HE-INT (Wit
Page 75 and 76: 366D000M 1/4/2011Cable Port Illustr
Page 77 and 78: 366D000M 1/4/201172
Page 79 and 80: 366D000M 1/4/201174
Page 81 and 82: 366D000M 1/4/201176
Page 83 and 84: 366D000M 1/4/2011FlexAIR Wiring78
Page 85 and 86: 366D000M 1/4/2011Getting the cabine
Page 87 and 88: 366D000M 1/4/20119) Bolt the leg in
Page 89 and 90: 366D000M 1/4/2011Step 3: Place stan
Page 91 and 92: 366D000M 1/4/2011Replacing Fluoresc
Page 93 and 94: 366D000M 1/4/2011Installation of Ex
Page 95 and 96: 366D000M 1/4/2011(This page intenti
Page 97 and 98: 366D000M 1/4/2011Balancing Damper C
Page 99 and 100: 366D000M 1/4/2011Installation Instr
Page 101 and 102: 366D000M 1/4/2011TopBypass bracket
Page 103 and 104: 366D000M 1/4/2011Step# 2: Position
Page 105: 366D000M 1/4/2011(This page intenti
Page 109 and 110: 366D000M 1/4/20115. Insert the 7”
Page 111 and 112: 366D000M 1/4/2011Motor Control Adju
Page 113 and 114: 366D000M 1/4/20114.) With the drive
Page 115: 366D000M 1/4/2011WarrantyThe Baker
show all

OPERATOR'S MANUAL - The Baker Company Blog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?