OPERATOR'S MANUAL - The Baker Company Blog

More documents

Recommendations

Info

366D000M 1/4/2011Electrical SpecificationsAll electrical wiring to the cabinet should comply with the National Electrical Codeand any applicable Local Electrical Codes at the site of installation.A single dedicated circuit is required to power this cabinet. This circuit shall provide the protective earth groundfor the cabinet.The unit is furnished with one 14' power cord with an appropriate Listed/approved plug for the destinationcountry.The power cord is the Main Disconnect device for the unit. The unit should bepositioned in a manner that allows easy access to the power cord connection to theelectrical utility.The cabinet is provided with two outlets. The outlet(s) on this circuit are protected by a self-resetting circuitbreaker. The breaker allows 5A total on all outlets.Cabinet Ratings: SGxxxA-HE115V AC, 16A, 60Hz, Single Phase, Dedicated circuit.Typical current (less outlets) for SG403A-HE 4.0 – 6.0 AmpsTypical current (less outlets) for SG503A-HE 5.0 – 7.0 AmpsTypical current (less outlets) for SG603A-HE 5.0 – 8.0 Amps(Note: Actual current values will vary depending on cabinet configuration.)The cabinet is internally protected with a 250V, 20A Circuit breaker.Cabinet Ratings: SGxxxA-HE-INT220V AC, 13A, 50/60Hz, Single Phase, Dedicated circuit.Typical current (less outlets) for SG403A-HE-INT 2.0 – 3.0 AmpsTypical current (less outlets) for SG603A-HE-INT 4.0 – 5.0 Amps(Note: Actual current values will vary depending on cabinet configuration.)The Motor/Control circuit (less outlets) is protected by 6.3A, Time Delay FusesThe cabinet may be provided with an optional lift that requires 2 Amps intermittent duty.The lift duty cycle is 1 minute on, 9 minutes off.The cabinet may be provided with an optional UV lamp.The UV lamp and Fluorescent lamp are interlocked to prevent simultaneous operation.The cabinet may be provided with an optional 24V DC power supply for low voltage options.7
366D000M 1/4/2011Environmental ConditionsThe cabinet is designed for use in the following conditions:• Indoor use• Altitudes up to 2000 meters• Temperature range from 41° F (5°C) to 104° F (40°C)• Maximum relative humidity 80% for temperatures up to 88° F (31°C) decreasing linearly to50% at 104° F (40°C)• Main Supply voltage: Rated Voltage stated in Cabinet Ratings ±10%V AC• Transient over voltage according to Installation Category (OVERVOLTAGE CATEGORIES)II per UL/IEC61010-1, 2 nd Edition• Pollution Degree 2Symbols and TerminologyProtective Earth: Any terminal intended for connection to external protective conductor forprotection against electric shock in case of a fault.!General Caution: Refer to instruction manual for information regarding personnel and environmentprotection.8
Page 1 and 2: THE BAKER COMPANYOPERATOR’S MANUA
Page 3 and 4: TABLE OF CONTENTSI - FUNCTION OF TH
Page 5 and 6: Stand Assembly Leg Extension Proced
Page 7 and 8: 366D000M 1/4/2011Base Features• M
Page 9 and 10: 366D000M 1/4/2011has 7/16” [11.1m
Page 11: 366D000M 1/4/2011SpecificationsWeig
Page 15 and 16: 366D000M 1/4/20111. Remove the stra
Page 17 and 18: 366D000M 1/4/2011The *FlexAIR is an
Page 19 and 20: 366D000M 1/4/2011Auxiliary Wiring O
Page 21 and 22: 366D000M 1/4/2011Auxiliary Cabinet
Page 23 and 24: 366D000M 1/4/2011• Ultraviolet (U
Page 25 and 26: 366D000M 1/4/2011The Double Proximi
Page 27 and 28: 366D000M 1/4/20113. Because opening
Page 29 and 30: 366D000M 1/4/2011cabinets, since th
Page 31 and 32: 366D000M 1/4/2011Recommended Decont
Page 33 and 34: 366D000M 1/4/2011Method to seal an
Page 35 and 36: 366D000M 1/4/20116. Tape sheeting t
Page 37 and 38: 366D000M 1/4/2011and allow the two
Page 39 and 40: 366D000M 1/4/2011IV - ONSITE CHECKS
Page 41 and 42: 366D000M 1/4/2011the front, lowerin
Page 43 and 44: 366D000M 1/4/2011A chemically conta
Page 45 and 46: 366D000M 1/4/2011at a time until th
Page 47 and 48: 366D000M 1/4/2011TroubleshootingIMP
Page 49 and 50: 366D000M 1/4/2011V - DISASSEMBLY IN
Page 51 and 52: 366D000M 1/4/2011Appendix46
Page 53 and 54: 366D000M 1/4/2011Baker Part NumberM
Page 55 and 56: 366D000M 1/4/2011SG403A-HE (With Ch
Page 57 and 58: 366D000M 1/4/2011SG403A-HE (With Hy
Page 59 and 60: 366D000M 1/4/2011SG503A-HE (Base Un
Page 61 and 62: 366D000M 1/4/2011SG503A-HE (With Ch
Page 63 and 64:
366D000M 1/4/2011SG503A-HE W/Canopy
Page 65 and 66:
366D000M 1/4/2011SG603A-HE (With Ch
Page 67 and 68:
366D000M 1/4/2011SG603A-HE (With Hy
Page 69 and 70:
366D000M 1/4/2011SG403A-HE-INT (Wit
Page 71 and 72:
366D000M 1/4/2011SG403A-HE-INT (Wit
Page 73 and 74:
366D000M 1/4/2011SG603A-HE-INT (Wit
Page 75 and 76:
366D000M 1/4/2011Cable Port Illustr
Page 77 and 78:
366D000M 1/4/201172
Page 79 and 80:
366D000M 1/4/201174
Page 81 and 82:
366D000M 1/4/201176
Page 83 and 84:
366D000M 1/4/2011FlexAIR Wiring78
Page 85 and 86:
366D000M 1/4/2011Getting the cabine
Page 87 and 88:
366D000M 1/4/20119) Bolt the leg in
Page 89 and 90:
366D000M 1/4/2011Step 3: Place stan
Page 91 and 92:
366D000M 1/4/2011Replacing Fluoresc
Page 93 and 94:
366D000M 1/4/2011Installation of Ex
Page 95 and 96:
366D000M 1/4/2011(This page intenti
Page 97 and 98:
366D000M 1/4/2011Balancing Damper C
Page 99 and 100:
366D000M 1/4/2011Installation Instr
Page 101 and 102:
366D000M 1/4/2011TopBypass bracket
Page 103 and 104:
366D000M 1/4/2011Step# 2: Position
Page 105 and 106:
366D000M 1/4/2011(This page intenti
Page 107 and 108:
366D000M 1/4/201112) Adjust the tot
Page 109 and 110:
366D000M 1/4/20115. Insert the 7”
Page 111 and 112:
366D000M 1/4/2011Motor Control Adju
Page 113 and 114:
366D000M 1/4/20114.) With the drive
Page 115:
366D000M 1/4/2011WarrantyThe Baker
show all

OPERATOR'S MANUAL - The Baker Company Blog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?