OPERATOR'S MANUAL - The Baker Company Blog

More documents

Recommendations

Info

366D000M 1/4/2011Exhaust airflowBuilding exhaust ductwork0.813” Diameter holeNut(Interior mounted)Seal washerStrain relief connectorRecommended 2 duct diameters spacingFigure 3: Example of exhaust duct with port for AFM probe used with CECConnection point to CEC collar orany other ductwork that affectsairflow (elbows, transitions,dampers, etc.)105
366D000M 1/4/2011Motor Control Adjustment DetailSG-HE OR SG-HE-INT & SG-HE-INT (EN)Trim pot positioningUnder normal operating conditions the motor control should not require adjustment except when setting ofalarms.CAUTION: DO NOT ADJUST ANY OTHER TRIMPOTS OTHER THAN THE ONES DESCRIBED INTHIS PROCEDURE.During the motor speed adjustment process the only two trim pots used are the ones marked DEC/B and COMP.DEC/B trim pot changes controller from auto normal operating mode (maximum counter clockwise) to manualoperating mode (maximum clockwise).COMP trim pot increases motor speed (turn clockwise) or decrease motor speed (turn counter clockwise).6.1) To adjust motor speed, turn DEC/B trim pot from auto to manual (maximum clockwise).6.2) Turn COMP trim pot to increase and decrease motor speed to the desired airflow alarm point. See factorytest report for alarm setting and test procedure.6.3) Return DEC/B trim pot to auto normal operating mode (maximum counter clockwise) after alarm testing iscomplete.106
Page 1 and 2:
THE BAKER COMPANYOPERATOR’S MANUA
Page 3 and 4:
TABLE OF CONTENTSI - FUNCTION OF TH
Page 5 and 6:
Stand Assembly Leg Extension Proced
Page 7 and 8:
366D000M 1/4/2011Base Features• M
Page 9 and 10:
366D000M 1/4/2011has 7/16” [11.1m
Page 11 and 12:
366D000M 1/4/2011SpecificationsWeig
Page 13 and 14:
366D000M 1/4/2011Environmental Cond
Page 15 and 16:
366D000M 1/4/20111. Remove the stra
Page 17 and 18:
366D000M 1/4/2011The *FlexAIR is an
Page 19 and 20:
366D000M 1/4/2011Auxiliary Wiring O
Page 21 and 22:
366D000M 1/4/2011Auxiliary Cabinet
Page 23 and 24:
366D000M 1/4/2011• Ultraviolet (U
Page 25 and 26:
366D000M 1/4/2011The Double Proximi
Page 27 and 28:
366D000M 1/4/20113. Because opening
Page 29 and 30:
366D000M 1/4/2011cabinets, since th
Page 31 and 32:
366D000M 1/4/2011Recommended Decont
Page 33 and 34:
366D000M 1/4/2011Method to seal an
Page 35 and 36:
366D000M 1/4/20116. Tape sheeting t
Page 37 and 38:
366D000M 1/4/2011and allow the two
Page 39 and 40:
366D000M 1/4/2011IV - ONSITE CHECKS
Page 41 and 42:
366D000M 1/4/2011the front, lowerin
Page 43 and 44:
366D000M 1/4/2011A chemically conta
Page 45 and 46:
366D000M 1/4/2011at a time until th
Page 47 and 48:
366D000M 1/4/2011TroubleshootingIMP
Page 49 and 50:
366D000M 1/4/2011V - DISASSEMBLY IN
Page 51 and 52:
366D000M 1/4/2011Appendix46
Page 53 and 54:
366D000M 1/4/2011Baker Part NumberM
Page 55 and 56:
366D000M 1/4/2011SG403A-HE (With Ch
Page 57 and 58:
366D000M 1/4/2011SG403A-HE (With Hy
Page 59 and 60: 366D000M 1/4/2011SG503A-HE (Base Un
Page 61 and 62: 366D000M 1/4/2011SG503A-HE (With Ch
Page 63 and 64: 366D000M 1/4/2011SG503A-HE W/Canopy
Page 65 and 66: 366D000M 1/4/2011SG603A-HE (With Ch
Page 67 and 68: 366D000M 1/4/2011SG603A-HE (With Hy
Page 69 and 70: 366D000M 1/4/2011SG403A-HE-INT (Wit
Page 75 and 76: 366D000M 1/4/2011Cable Port Illustr
Page 77 and 78: 366D000M 1/4/201172
Page 79 and 80: 366D000M 1/4/201174
Page 81 and 82: 366D000M 1/4/201176
Page 83 and 84: 366D000M 1/4/2011FlexAIR Wiring78
Page 85 and 86: 366D000M 1/4/2011Getting the cabine
Page 87 and 88: 366D000M 1/4/20119) Bolt the leg in
Page 89 and 90: 366D000M 1/4/2011Step 3: Place stan
Page 91 and 92: 366D000M 1/4/2011Replacing Fluoresc
Page 93 and 94: 366D000M 1/4/2011Installation of Ex
Page 95 and 96: 366D000M 1/4/2011(This page intenti
Page 97 and 98: 366D000M 1/4/2011Balancing Damper C
Page 99 and 100: 366D000M 1/4/2011Installation Instr
Page 101 and 102: 366D000M 1/4/2011TopBypass bracket
Page 103 and 104: 366D000M 1/4/2011Step# 2: Position
Page 105 and 106: 366D000M 1/4/2011(This page intenti
Page 107 and 108: 366D000M 1/4/201112) Adjust the tot
Page 109: 366D000M 1/4/20115. Insert the 7”
Page 113 and 114: 366D000M 1/4/20114.) With the drive
Page 115: 366D000M 1/4/2011WarrantyThe Baker
show all

OPERATOR'S MANUAL - The Baker Company Blog

Create successful ePaper yourself

Delete template?

Save as template?