OPERATOR'S MANUAL - The Baker Company Blog

More documents

Recommendations

Info

366D000M 1/4/20113. With sheet plastic 4-mil thick or thicker, cuta piece large enough to tape over the topextending down the front to the bottom ofthe drain pan and around to the side panels.(See Figure 5)Figure 54. Center the plastic sheeting over the cabinetfrom right to left.Using 76.2mm (3”) wide good qualityplastic tape, start taping the sheeting at thetop rear of the cabinet over all cablebrackets. This area provides a flat surfacethe length of the top panel for taping. Avoidwrinkling the sheeting. (See Figures 6 and7)Figure 6Figure 75. Continue to tape the sheeting around theback corner down the sides. If present, tapeover cable ports or plug with cable port plugprovided.Fold and overlap plastic as required to get atight fit on the sides. Tape folds in place.(See Figures 8-11)Cable Port PlugFigure 8Figure 9Cable PortFigure 10Figure 1129
366D000M 1/4/20116. Tape sheeting to lower front corners. Trimsheeting as required to achieve a good fit.Make sure tape covers seams so there are noleaks. (See Figures 12 and 13)Figure 12Figure 137. Tape the plastic sheeting across the front ofcabinet drain pan. Avoid wrinkling thesheeting. (See Figure 14)Figure 1430
Page 1 and 2: THE BAKER COMPANYOPERATOR’S MANUA
Page 3 and 4: TABLE OF CONTENTSI - FUNCTION OF TH
Page 5 and 6: Stand Assembly Leg Extension Proced
Page 7 and 8: 366D000M 1/4/2011Base Features• M
Page 9 and 10: 366D000M 1/4/2011has 7/16” [11.1m
Page 11 and 12: 366D000M 1/4/2011SpecificationsWeig
Page 13 and 14: 366D000M 1/4/2011Environmental Cond
Page 15 and 16: 366D000M 1/4/20111. Remove the stra
Page 17 and 18: 366D000M 1/4/2011The *FlexAIR is an
Page 19 and 20: 366D000M 1/4/2011Auxiliary Wiring O
Page 21 and 22: 366D000M 1/4/2011Auxiliary Cabinet
Page 23 and 24: 366D000M 1/4/2011• Ultraviolet (U
Page 25 and 26: 366D000M 1/4/2011The Double Proximi
Page 27 and 28: 366D000M 1/4/20113. Because opening
Page 29 and 30: 366D000M 1/4/2011cabinets, since th
Page 31 and 32: 366D000M 1/4/2011Recommended Decont
Page 33: 366D000M 1/4/2011Method to seal an
Page 37 and 38: 366D000M 1/4/2011and allow the two
Page 39 and 40: 366D000M 1/4/2011IV - ONSITE CHECKS
Page 41 and 42: 366D000M 1/4/2011the front, lowerin
Page 43 and 44: 366D000M 1/4/2011A chemically conta
Page 45 and 46: 366D000M 1/4/2011at a time until th
Page 47 and 48: 366D000M 1/4/2011TroubleshootingIMP
Page 49 and 50: 366D000M 1/4/2011V - DISASSEMBLY IN
Page 51 and 52: 366D000M 1/4/2011Appendix46
Page 53 and 54: 366D000M 1/4/2011Baker Part NumberM
Page 55 and 56: 366D000M 1/4/2011SG403A-HE (With Ch
Page 57 and 58: 366D000M 1/4/2011SG403A-HE (With Hy
Page 59 and 60: 366D000M 1/4/2011SG503A-HE (Base Un
Page 63 and 64: 366D000M 1/4/2011SG503A-HE W/Canopy
Page 67 and 68: 366D000M 1/4/2011SG603A-HE (With Hy
Page 69 and 70: 366D000M 1/4/2011SG403A-HE-INT (Wit
Page 75 and 76: 366D000M 1/4/2011Cable Port Illustr
Page 77 and 78: 366D000M 1/4/201172
Page 79 and 80: 366D000M 1/4/201174
Page 81 and 82: 366D000M 1/4/201176
Page 83 and 84: 366D000M 1/4/2011FlexAIR Wiring78
Page 85 and 86:
366D000M 1/4/2011Getting the cabine
Page 87 and 88:
366D000M 1/4/20119) Bolt the leg in
Page 89 and 90:
366D000M 1/4/2011Step 3: Place stan
Page 91 and 92:
366D000M 1/4/2011Replacing Fluoresc
Page 93 and 94:
366D000M 1/4/2011Installation of Ex
Page 95 and 96:
366D000M 1/4/2011(This page intenti
Page 97 and 98:
366D000M 1/4/2011Balancing Damper C
Page 99 and 100:
366D000M 1/4/2011Installation Instr
Page 101 and 102:
366D000M 1/4/2011TopBypass bracket
Page 103 and 104:
366D000M 1/4/2011Step# 2: Position
Page 105 and 106:
366D000M 1/4/2011(This page intenti
Page 107 and 108:
366D000M 1/4/201112) Adjust the tot
Page 109 and 110:
366D000M 1/4/20115. Insert the 7”
Page 111 and 112:
366D000M 1/4/2011Motor Control Adju
Page 113 and 114:
366D000M 1/4/20114.) With the drive
Page 115:
366D000M 1/4/2011WarrantyThe Baker
show all

OPERATOR'S MANUAL - The Baker Company Blog

Create successful ePaper yourself

Delete template?

Save as template?