OPERATOR'S MANUAL - The Baker Company Blog

More documents

Recommendations

Info

366D000M 1/4/2011Exhausting Requirements for CEC:CabinetModelTransitionModelSashHeight(Inchs)*ExhaustFlow RateMin/Max(cfm)PressureLossMin/Max(” w.c.)PressureLoss withBSC Sealedfor Decon.(” w.c.)**IntakeVelocity(fpm)AdditionalHeights(Inchs)ExhaustDuct Dia.(Inchs)SG 403A-HESG 403A-HESG 403A-HESG 503A-HECEC403A-HECEC403A-HECEC403A-HECEC503A-HE8”[203.2mm]10”[254mm]12”[304.8mm]8”[203.2mm]322 / 520[152 / 245L/sec]401 / 585[189 / 276L/sec]438 / 614[207 / 290L/sec]412 / 680[194 / 321L/sec]0.05 / 0.25[12.4 /62.3 Pa]0.08 / 0.30[19.9 /74.7 Pa]0.09 / .40[22.4 /99.6 Pa]0.10 / 0.35[24.9 /87.2 Pa]0.20[49.8 Pa]0.30[74.7 Pa]0.40[99.6 Pa]0.20[49.8 Pa]89[0.452m/sec]82[0.416m/sec]77[0.391m/sec]93[0.472m/sec]ET3.80”Decon Box3.00”Short Collar1.50”ATD7.75”SAME ASABOVESAME ASABOVESAME ASABOVE10[254mm]10[254mm]10[254mm]10[254mm]SG 503A-HECEC503A-HE10”[254mm]N/A N/A N/A N/ASAME ASABOVE10[254mm]SG 503A-HESG 603A-HESG 603A-HESG 603A-HECEC503A-HECEC603A-HECEC603A-HECEC603A-HE12”[304.8mm]8”[203.2mm]10”[254mm]12”[304.8mm]618 / 770[292 / 363L/sec]490 / 754[231 / 356L/sec]613 / 914[289 / 431L/sec]665 / 1015[314 / 479L/sec]0.20 / .40[49.8 /99.6 Pa]0.15 / 0.40[37.4 /99.6 Pa]0.20 / 0.50[49.8 /124 Pa]0.20 / 0.50[49.8 /124 Pa]0.25[62.3 Pa]0.34[84.7 Pa]0.60[149 Pa]0.75[186.3 Pa]94[0.477m/sec]85[0.432m/sec]84[0.427m/sec]82[0.416m/sec]SAME ASABOVESAME ASABOVESAME ASABOVESAME ASABOVE10[254mm]10[254mm]10[254mm]10[254mm]Exhaust requirements for Canopy Exhaust Connection (CEC)* = All exhaust flow rates are based on a nominal 105 fpm [0.533 m/sec] intake velocity.** = When building exhaust is off, cabinet running.89
366D000M 1/4/2011(This page intentionally left blank)90
Page 1 and 2:
THE BAKER COMPANYOPERATOR’S MANUA
Page 3 and 4:
TABLE OF CONTENTSI - FUNCTION OF TH
Page 5 and 6:
Stand Assembly Leg Extension Proced
Page 7 and 8:
366D000M 1/4/2011Base Features• M
Page 9 and 10:
366D000M 1/4/2011has 7/16” [11.1m
Page 11 and 12:
366D000M 1/4/2011SpecificationsWeig
Page 13 and 14:
366D000M 1/4/2011Environmental Cond
Page 15 and 16:
366D000M 1/4/20111. Remove the stra
Page 17 and 18:
366D000M 1/4/2011The *FlexAIR is an
Page 19 and 20:
366D000M 1/4/2011Auxiliary Wiring O
Page 21 and 22:
366D000M 1/4/2011Auxiliary Cabinet
Page 23 and 24:
366D000M 1/4/2011• Ultraviolet (U
Page 25 and 26:
366D000M 1/4/2011The Double Proximi
Page 27 and 28:
366D000M 1/4/20113. Because opening
Page 29 and 30:
366D000M 1/4/2011cabinets, since th
Page 31 and 32:
366D000M 1/4/2011Recommended Decont
Page 33 and 34:
366D000M 1/4/2011Method to seal an
Page 35 and 36:
366D000M 1/4/20116. Tape sheeting t
Page 37 and 38:
366D000M 1/4/2011and allow the two
Page 39 and 40:
366D000M 1/4/2011IV - ONSITE CHECKS
Page 41 and 42:
366D000M 1/4/2011the front, lowerin
Page 43 and 44: 366D000M 1/4/2011A chemically conta
Page 45 and 46: 366D000M 1/4/2011at a time until th
Page 47 and 48: 366D000M 1/4/2011TroubleshootingIMP
Page 49 and 50: 366D000M 1/4/2011V - DISASSEMBLY IN
Page 51 and 52: 366D000M 1/4/2011Appendix46
Page 53 and 54: 366D000M 1/4/2011Baker Part NumberM
Page 55 and 56: 366D000M 1/4/2011SG403A-HE (With Ch
Page 57 and 58: 366D000M 1/4/2011SG403A-HE (With Hy
Page 59 and 60: 366D000M 1/4/2011SG503A-HE (Base Un
Page 63 and 64: 366D000M 1/4/2011SG503A-HE W/Canopy
Page 67 and 68: 366D000M 1/4/2011SG603A-HE (With Hy
Page 69 and 70: 366D000M 1/4/2011SG403A-HE-INT (Wit
Page 75 and 76: 366D000M 1/4/2011Cable Port Illustr
Page 77 and 78: 366D000M 1/4/201172
Page 79 and 80: 366D000M 1/4/201174
Page 81 and 82: 366D000M 1/4/201176
Page 83 and 84: 366D000M 1/4/2011FlexAIR Wiring78
Page 85 and 86: 366D000M 1/4/2011Getting the cabine
Page 87 and 88: 366D000M 1/4/20119) Bolt the leg in
Page 89 and 90: 366D000M 1/4/2011Step 3: Place stan
Page 91 and 92: 366D000M 1/4/2011Replacing Fluoresc
Page 93: 366D000M 1/4/2011Installation of Ex
Page 97 and 98: 366D000M 1/4/2011Balancing Damper C
Page 99 and 100: 366D000M 1/4/2011Installation Instr
Page 101 and 102: 366D000M 1/4/2011TopBypass bracket
Page 103 and 104: 366D000M 1/4/2011Step# 2: Position
Page 105 and 106: 366D000M 1/4/2011(This page intenti
Page 107 and 108: 366D000M 1/4/201112) Adjust the tot
Page 109 and 110: 366D000M 1/4/20115. Insert the 7”
Page 111 and 112: 366D000M 1/4/2011Motor Control Adju
Page 113 and 114: 366D000M 1/4/20114.) With the drive
Page 115: 366D000M 1/4/2011WarrantyThe Baker
show all

OPERATOR'S MANUAL - The Baker Company Blog

Create successful ePaper yourself

Delete template?

Save as template?