- Page 7 and 8: FNC Key............................
- Page 9 and 10: IntroductionThe Leica Geosystems TP
- Page 13: Standing axis inclinationAngle betw
- Page 18 and 19: Operating the InstrumentThe On / Of
- Page 20 and 21: Distance measurementA laser distanc
- Page 22 and 23: Red laser to prismsAccurate measure
- Page 24 and 25: SymbolsDepending on software versio
- Page 26 and 27: Measuring Preparation / Setting upU
- Page 28 and 29: When using the GEB121 battery, remo
- Page 30 and 31: Setting up the tripod1. Loosen the
- Page 32 and 33: Setup step-by-step1321161. Extend t
- Page 34 and 35: Laser intensityChanging the laser i
- Page 36 and 37: Edit modeExisting characters are ch
- Page 38 and 39: Numerical and Alphanumerical inputI
- Page 40 and 41: PointsearchPointsearch is a global
- Page 42 and 43: MeasuringAfter switching on and set
- Page 44 and 45: Delete Last RecordThis function del
- Page 46 and 47: Procedure:P0TPS800_Z158αHzLdHzRRP1
- Page 48 and 49: This function determines the height
- Page 50 and 51: ProgramsApplication pre-settingsThe
- Page 52 and 53:
OrientationWith the orientation, Hz
- Page 54 and 55:
Displaying residuals[RESID] Display
- Page 56 and 57:
ApplicationsIntroductionApplication
- Page 58 and 59:
Stake outThis program calculates th
- Page 60 and 61:
Free StationThe application "Free S
- Page 62 and 63:
Procedure:Here you can enter a limi
- Page 64 and 65:
If the instrument height was set to
- Page 66 and 67:
Warnings / MessagesImportant messag
- Page 68 and 69:
2. Shifting/Rotating the Base lineT
- Page 70 and 71:
L+RLOff+MPREFERENCE LINEPtID : 140h
- Page 72 and 73:
Example "orthogonal stake out"Displ
- Page 74 and 75:
Radial Method:Centre pointSlope dis
- Page 76 and 77:
Area & VolumeThe application progra
- Page 78 and 79:
P0TPS800_Z101P1cbP4P2P3adagf eP0 St
- Page 80 and 81:
ConstructionThis application allows
- Page 82 and 83:
During use of the application the p
- Page 84 and 85:
IntersectionsBearing - BearingBeari
- Page 86 and 87:
OffsetSet Point by ...Distance - Of
- Page 88 and 89:
Reference Plane (optional)The appli
- Page 90 and 91:
Procedure1. Measuring points defini
- Page 92 and 93:
Procedure:Select code from a codeli
- Page 94 and 95:
Sector BeepOff Sector Beep switched
- Page 96 and 97:
InternTPS400-5.0.1enAll data is rec
- Page 98 and 99:
EDM SettingsThe EDM-settings contai
- Page 100 and 101:
Prism ConstantCalling the function
- Page 102 and 103:
• Ht. a. MSLHeight above sea leve
- Page 104 and 105:
FixpointsValid fixed points contain
- Page 106 and 107:
Start-up sequenceSets the screen th
- Page 108 and 109:
Line-of-sight error (Hz-collimation
- Page 110 and 111:
Warnings / MessagesImportant Messag
- Page 112 and 113:
Data TransferWith this special func
- Page 114 and 115:
Instrument Protection with PINThe i
- Page 116 and 117:
Inside vehicleNever transport the p
- Page 118 and 119:
CleaningFogging of prisms:Reflector
- Page 120 and 121:
Circular level on the tribrachLevel
- Page 122 and 123:
Safety DirectionsThe following dire
- Page 124 and 125:
ResponsibilitiesManufacturer of the
- Page 126 and 127:
the safety authorities responsible
- Page 128 and 129:
Precautions:The product must not be
- Page 130 and 131:
DescriptionMaximum average radiant
- Page 132 and 133:
Distancer, Measurements without Ref
- Page 134 and 135:
LabellingLaser ApertureLaser Radiat
- Page 136 and 137:
Electronic Guide Light EGLThe integ
- Page 138 and 139:
LabellingLaser RadiationDo not star
- Page 140 and 141:
Precautions:Use only the equipment
- Page 142 and 143:
Labelling:........ ..........: ....
- Page 144 and 145:
Laser plummet• Location: ........
- Page 146 and 147:
Distance measurement (IR: Reflector
- Page 148 and 149:
EDMmeasuringprogramStandard**Accura
- Page 150 and 151:
Atmospheric correction in ppm with
- Page 152 and 153:
Y = · |sin ζ |X = · cos ζζ = v
- Page 154 and 155:
http://www.leica-geosystems.com/swl
- Page 156 and 157:
Contrast ..........................
- Page 158 and 159:
LLabelling ........................
- Page 160 and 161:
Software Upload ...................
- Page 162:
Total Quality Management: Our commi