Leica TPS400 Series User Manual

More documents

Recommendations

Info

Example "orthogonal stake out"Display in "Stake out" measure mode:RLSPL-O-MPORTHOGONAL STAKEOUT 1/2PtID : 15hr :1.500 mHz :+0.200 g: 2.368 m: 0.260 mDISTRECIRITPS800_Z401RP1RP: 1st reference pointRL: Reference lineMP: Measured pointSP: Stake out pointL: Longitudinal offsetOff: Parallel offsetOffset:2.040 mLine :1.203 m: 0.260 mThe signs for the distance and angle differences arecorrection values (required minus actual).+Hz Turn telescope clockwise to the stakeout point.+ The stake out point is further away thanthe point measured.<strong>TPS400</strong>-5.0.1en72 Programs
+ The stake out point is higher than themeasured point.Warnings / MessagesImportantMessagesSave viaRS232 !Base line tooshort !Coordinatesinvalid !MeaningData output (system setting menu) viaRS232 interface is activated. To be ableto succesfully start reference line, the"INTERN" setting must be enabled.Base line is shorter than 1 cm. Choosebase points such that the horizontalseparation of both points is at least 1 cm.No coordinates or invalid coordinates fora point. Ensure that a point used has atleast one Easting and one Northing coordinate.Tie DistanceThe application Tie Distance computes slopedistance, horizontal distance, height difference andazimuth of two target points measured online,selected from the Memory or entered using theKeypad.The user can choose between two differentmethods:Polygonal (A-B, B-C)Radial (A-B, A-C)Polygonal Method:Programs73<strong>TPS400</strong>-5.0.1en
Page 4:
Validity of this manualDescriptionG
Page 8 and 9:
Shipping ..........................
Page 10:
Special features• Easy and quickl
Page 17 and 18:
Power SupplyUse the Leica Geosystem
Page 19 and 20:
Fixed keys[PAGE] Scrolls to next pa
Page 21 and 22: Incorrect resultReflectorlessBe sur
Page 23 and 24: SoftkeysUnder softkeys, a selection
Page 25 and 26: Menu tree[MENU] > - Confirm menu se
Page 27 and 28: Inserting / Replacing Battery2. Rem
Page 29 and 30: External power supply for totalstat
Page 31 and 32: Careful handling of tripod• Check
Page 33 and 34: Levelling up with the electronic le
Page 35 and 36: Input mode - method 1In entry mode,
Page 37 and 38: Inserting charactersIf a character
Page 39 and 40: Character setEntry mode contains th
Page 41 and 42: Wildcard searchThe Wildcard search
Page 43 and 44: FNC KeyUnder [FNC] several function
Page 45 and 46: Enter offset values!Trav. Offset: 0
Page 47 and 48: 5 [ALL] Completes the measurement a
Page 49 and 50: Procedure:1. Measure to first prism
Page 51 and 52: Setting StationEach coordinate comp
Page 53 and 54: Orientation coordinates can be eith
Page 55 and 56: Useful information• If the orient
Page 57 and 58: SurveyingWith the program Surveying
Page 59 and 60: Orthogonal Stake outThe position of
Page 61 and 62: Measuring facilitiesSingle face I o
Page 63 and 64: [AddPt] Input another backsight poi
Page 65 and 66: [Disable]/[Enable]Excludes/includes
Page 67 and 68: Reference LineThis program facilita
Page 69 and 70: REFERENCE LINE - MAIN 1/2Length : 1
Page 71: Example "relative to first referenc
Page 75 and 76: Softkeys - radial method:[NewPt 1]
Page 77 and 78: 1. Determine area points[ALL] Start
Page 79 and 80: Remote HeightPoints directly above
Page 81 and 82: Measured point height is above line
Page 83 and 84: Inverse & TraverseTraverseInversed1
Page 85 and 86: Distance - DistanceBy PointsTPS800_
Page 87 and 88: Plane OffsetP2ExtensionThe "Extensi
Page 89 and 90: P4P5XZOff+XZMeasured point. This po
Page 91 and 92: Offset:X:Z:[New Tgt][STAKE][New Pla
Page 93 and 94: SettingsThis menu enables extensive
Page 95 and 96: BeepThe beep is an acoustic signal
Page 97 and 98: gon possible angle values: 0 gon to
Page 99 and 100: RL-StandardFor distance measurement
Page 101 and 102: [SCALE]Scale of projection.[ATMOS]I
Page 103 and 104: File ManagementThe File Manager con
Page 105 and 106: [DELETE] Starts deleting process wi
Page 107 and 108: CalibrationsDetermining Line-of-sig
Page 109 and 110: Hz-collimationV-indexDisplay adjust
Page 111 and 112: COMM ParametersFor data transfer be
Page 113 and 114: System InfoDisplays helpful informa
Page 115 and 116: Care and StorageTransportWhen trans
Page 117 and 118: If the product becomes wet, leave i
Page 119 and 120: Checking and adjustingTripodCircula
Page 121 and 122: Depending on brightness and surface
Page 123 and 124:
• Use of products with obviously
Page 125 and 126:
Hazards of Use WARNINGThe absence o
Page 127 and 128:
Precautions:Adhere to the instructi
Page 129 and 130:
Laser classificationGeneralThe foll
Page 131 and 132:
LabellingType: TC.... Art.No.: ....
Page 133 and 134:
WARNINGPotential hazards are not on
Page 135 and 136:
Type: TC.... Art.No.: ......Power:
Page 137 and 138:
Laser plummetThe laser plummet buil
Page 139 and 140:
1) Exit for laser beam2) Laser beam
Page 141 and 142:
FCC Statement (Applicable in U.S.)
Page 143 and 144:
Technical DataTelescope• Transit
Page 145 and 146:
• External supply(via serial inte
Page 147 and 148:
Distance measurement (RL: Reflector
Page 149 and 150:
Atmospheric correctionThe distance
Page 151 and 152:
Reduction formulaeThe instrument ca
Page 153 and 154:
International Limited Warranty, Sof
Page 155 and 156:
IndexAAbbreviations ...............
Page 157 and 158:
GSI-coding ........................
Page 159 and 160:
Parity ............................
Page 161 and 162:
ZZenith ...........................
show all

Leica TPS400 Series User Manual

Create successful ePaper yourself

Delete template?

Save as template?