Leica TPS400 Series User Manual

More documents

Recommendations

Info

L+RLOff+MPREFERENCE LINEPtID : 140hr :1.500 mOffset:0.208 mLine :0.349 m: 1.203 mIRITPS800_Z381RPDISTREC1RP:MP:RL:L:Off:1st reference pointMeasured pointReference lineLongitudinal offsetParallel offsetThe height of the first reference point is always usedas the reference height for the calculation of theheight differences ( ).<strong>TPS400</strong>-5.0.1en70 Programs
Example "relative to first reference point"1RPHd+1BPH+RHH-TPS800_Z395. "Stake out" subapplicationYou can enter longitudinal, parallel and heightoffsets for the target points to be set-out relative tothe reference line. The program calculates the differencebetween a measured point and the calculatedpoint. The program displays the orthogonal (Line,Offset, ) and the polar (Hz, , ) differences.Procedure:1. Input the orthogonal stake out elements.2. [OK] Confirm entry and start calculation.1RP:1BP:RH:Hd:H:1st reference point1st base pointReference heightHeight difference between reference andbase pointHeight difference from reference heightPrograms71<strong>TPS400</strong>-5.0.1en
Page 4:
Validity of this manualDescriptionG
Page 8 and 9:
Shipping ..........................
Page 10:
Special features• Easy and quickl
Page 17 and 18:
Power SupplyUse the Leica Geosystem
Page 19 and 20: Fixed keys[PAGE] Scrolls to next pa
Page 21 and 22: Incorrect resultReflectorlessBe sur
Page 23 and 24: SoftkeysUnder softkeys, a selection
Page 25 and 26: Menu tree[MENU] > - Confirm menu se
Page 27 and 28: Inserting / Replacing Battery2. Rem
Page 29 and 30: External power supply for totalstat
Page 31 and 32: Careful handling of tripod• Check
Page 33 and 34: Levelling up with the electronic le
Page 35 and 36: Input mode - method 1In entry mode,
Page 37 and 38: Inserting charactersIf a character
Page 39 and 40: Character setEntry mode contains th
Page 41 and 42: Wildcard searchThe Wildcard search
Page 43 and 44: FNC KeyUnder [FNC] several function
Page 45 and 46: Enter offset values!Trav. Offset: 0
Page 47 and 48: 5 [ALL] Completes the measurement a
Page 49 and 50: Procedure:1. Measure to first prism
Page 51 and 52: Setting StationEach coordinate comp
Page 53 and 54: Orientation coordinates can be eith
Page 55 and 56: Useful information• If the orient
Page 57 and 58: SurveyingWith the program Surveying
Page 59 and 60: Orthogonal Stake outThe position of
Page 61 and 62: Measuring facilitiesSingle face I o
Page 63 and 64: [AddPt] Input another backsight poi
Page 65 and 66: [Disable]/[Enable]Excludes/includes
Page 67 and 68: Reference LineThis program facilita
Page 69: REFERENCE LINE - MAIN 1/2Length : 1
Page 73 and 74: + The stake out point is higher tha
Page 75 and 76: Softkeys - radial method:[NewPt 1]
Page 77 and 78: 1. Determine area points[ALL] Start
Page 79 and 80: Remote HeightPoints directly above
Page 81 and 82: Measured point height is above line
Page 83 and 84: Inverse & TraverseTraverseInversed1
Page 85 and 86: Distance - DistanceBy PointsTPS800_
Page 87 and 88: Plane OffsetP2ExtensionThe "Extensi
Page 89 and 90: P4P5XZOff+XZMeasured point. This po
Page 91 and 92: Offset:X:Z:[New Tgt][STAKE][New Pla
Page 93 and 94: SettingsThis menu enables extensive
Page 95 and 96: BeepThe beep is an acoustic signal
Page 97 and 98: gon possible angle values: 0 gon to
Page 99 and 100: RL-StandardFor distance measurement
Page 101 and 102: [SCALE]Scale of projection.[ATMOS]I
Page 103 and 104: File ManagementThe File Manager con
Page 105 and 106: [DELETE] Starts deleting process wi
Page 107 and 108: CalibrationsDetermining Line-of-sig
Page 109 and 110: Hz-collimationV-indexDisplay adjust
Page 111 and 112: COMM ParametersFor data transfer be
Page 113 and 114: System InfoDisplays helpful informa
Page 115 and 116: Care and StorageTransportWhen trans
Page 117 and 118: If the product becomes wet, leave i
Page 119 and 120: Checking and adjustingTripodCircula
Page 121 and 122:
Depending on brightness and surface
Page 123 and 124:
• Use of products with obviously
Page 125 and 126:
Hazards of Use WARNINGThe absence o
Page 127 and 128:
Precautions:Adhere to the instructi
Page 129 and 130:
Laser classificationGeneralThe foll
Page 131 and 132:
LabellingType: TC.... Art.No.: ....
Page 133 and 134:
WARNINGPotential hazards are not on
Page 135 and 136:
Type: TC.... Art.No.: ......Power:
Page 137 and 138:
Laser plummetThe laser plummet buil
Page 139 and 140:
1) Exit for laser beam2) Laser beam
Page 141 and 142:
FCC Statement (Applicable in U.S.)
Page 143 and 144:
Technical DataTelescope• Transit
Page 145 and 146:
• External supply(via serial inte
Page 147 and 148:
Distance measurement (RL: Reflector
Page 149 and 150:
Atmospheric correctionThe distance
Page 151 and 152:
Reduction formulaeThe instrument ca
Page 153 and 154:
International Limited Warranty, Sof
Page 155 and 156:
IndexAAbbreviations ...............
Page 157 and 158:
GSI-coding ........................
Page 159 and 160:
Parity ............................
Page 161 and 162:
ZZenith ...........................
show all

Leica TPS400 Series User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?