Thermo Scientific Orion 2110XP Ammonia Analyzer

More documents

Recommendations

Info

AppendixPipet OperationTip EjectionTo help eliminate the risk of contamination, each pipet is fitted with a tipejector system. The tip ejector system consists of a soft-touch tip ejectorand specially designed gearing mechanism. To release the tip, point thepipet at suitable waste receptacle and press the tip ejector with your thumb.You can attach the pipet shelf hanger on a counter, pipet stand or anywherewhere you want to hang your pipet.Clean the area where you plan to attach the shelf hanger. Apply two stickersto the underside of the shelf hanger. Press the shelf hanger firmly into placeon a shelf, counter top or pipet stand. To use, hang the grippy finger rest onthe shelf hanger.Thermo Scientific Orion 2110XP Ammonia Analyzer User GuideA-11
AppendixPipet TechniquesGeneralSpecial care should be taken to avoid liquid being aspirated into the interiorworking of the pipet. Push and release the push button slowly at all times,particularly when working with high viscosity liquids. Never allow the pushbutton to snap back. Make sure that the tip is firmly attached to the tipcone. Check for foreign particles in the tip.• Do not touch pipet tip with bare fingers. Risk of contamination ispossible. Use powder free gloves for protection.Before you begin your actual pipeting work, fill and empty the tip 3 to5 times with the solution that you will be pipeting. Hold the pipet in anupright position while aspirating liquid. The grippy should rest on yourindex finger. Make sure that the tips, pipet and solution are at the sametemperature.Forward TechniqueFill a clean reagent reservoir with the liquid to be dispensed.1. Depress the push button to the first stop.2. Dip the tip under the surface of the liquid in the reservoir to a depthof about 1 cm and slowly release the push button. Withdraw the tipfrom the liquid, touching it against the edge of the reservoir to removeexcess liquid.3. Deliver the liquid by gently depressing the push button to the first stop.After a delay of about one second, continue to depress the push buttonall the way to the second stop. This action will empty the tip.4. Release the push button to the ready position. If necessary, change thetip and continue pipeting.Thermo Scientific Orion 2110XP Ammonia Analyzer User GuideA-12
Page 1 and 2:
Thermo ScientificOrion 2110XPAmmoni
Page 3:
Table of ContentsChapter IGeneral I
Page 6 and 7:
General InformationFeatures and Ben
Page 8 and 9:
General InformationThe sensing elec
Page 10 and 11:
General InformationOffline Calibrat
Page 12 and 13:
General InformationGlossaryRefer to
Page 14 and 15:
General InformationTwo Channel Anal
Page 16 and 17:
Analyzer PreparationMounting andPlu
Page 18 and 19:
Analyzer PreparationElectrical Wiri
Page 20 and 21:
Analyzer PreparationWiring the Anal
Page 22 and 23:
Analyzer PreparationTerminalAssignm
Page 24 and 25:
Analyzer PreparationInstallation of
Page 26 and 27:
Analyzer PreparationInstallation of
Page 28 and 29:
Analyzer Preparation8. Invert the e
Page 30 and 31:
Analyzer OperationDescription ofKey
Page 32 and 33:
Analyzer OperationUsing PasswordPro
Page 34 and 35:
Analyzer OperationRSETReset the ana
Page 36 and 37:
Analyzer OperationALRMSet up to thr
Page 38 and 39:
Analyzer OperationDefault Operator
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Analyzer OperationWarning: The rese
Page 46 and 47:
Analyzer OperationNote: The followi
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Analyzer OperationStart-Up1. Replac
Page 66 and 67:
CalibrationFlow Cell OperationThe s
Page 68 and 69:
CalibrationAir RegulationThe Thermo
Page 70 and 71:
CalibrationPerforming aDKA Calibrat
Page 72 and 73: CalibrationStep Operator Action Scr
Page 74 and 75: CalibrationCalibrationAbort StepsTh
Page 76 and 77: CalibrationError Operator Action Sc
Page 78 and 79: CalibrationSpan CheckProcedureThe T
Page 80 and 81: CalibrationStep Operator Action Scr
Page 82 and 83: Analyzer MaintenanceMonthly Mainten
Page 84 and 85: Analyzer MaintenanceReplacement of
Page 86 and 87: Analyzer MaintenanceReplacement ofR
Page 88 and 89: TroubleshootingCalibration Log• D
Page 90 and 91: TroubleshootingMeasurement Log• D
Page 92 and 93: TroubleshootingElectronics Serial N
Page 94 and 95: TroubleshootingKeypad Test• The m
Page 96 and 97: TroubleshootingHigh SlopeSlope grea
Page 98 and 99: TroubleshootingMalfunction Possible
Page 100 and 101: TroubleshootingError/Event CodesErr
Page 102 and 103: TroubleshootingDisplayedEvent CodeD
Page 104 and 105: TroubleshootingHard ResetA hard res
Page 106 and 107: TroubleshootingAdvanced Replacement
Page 108 and 109: Customer ServiceDeclaration ofConfo
Page 110 and 111: Customer ServiceHazardous Materials
Page 112 and 113: AppendixMounting DimensionsORION 21
Page 114 and 115: AppendixSpecificationsAmmonia Measu
Page 116 and 117: AppendixOutputsNumber of Analog Out
Page 118 and 119: AppendixOrdering InformationCat. No
Page 120 and 121: AppendixField Replaceable PartsCat.
Page 125: Process Water InstrumentsNorth Amer
show all

Thermo Scientific Orion 2110XP Ammonia Analyzer

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?