Thermo Scientific Orion 2110XP Ammonia Analyzer

More documents

Recommendations

Info

Analyzer OperationRSETReset the analyzer to factory defaults for setup parameters:• Use to troubleshoot the system (a hard reset can be performed if thekeypad and software are not responding, refer to Chapter VI, Resettingthe Analyzer)Warning: Resetting the analyzer will lose all stored information includingrelay, logs and calibration settings.DISPSet the automatic lighting options for the backlit display:• AUtO – Brightness will change in response to ambient light source• On – Backlit display is always on• OFF – Backlit display is always off• Default display – AUtOThermo Scientific Orion 2110XP Ammonia Analyzer User GuideIII-6
Analyzer OperationChannel Specific SetupMode Menu OptionsCH1 or CH2If a two channel analyzer is in use, the following setup mode menu optionsare specific to the first channel of the 2110XP analyzer for ammoniameasurements. When a pH/ORP module or conductivity module isinstalled on the second channel of the 2110XP analyzer, refer to the ThermoScientific Orion 2100 Series pH/ORP Analyzer and Conductivity AnalyzerUser Guide for detailed instructions on the second channel setup modemenu options.The operator must select the channel number in the main setup mode(CH1 or CH2) and the menu options that are relative to the measurementcapability of that channel will be displayed. If a one channel analyzer isbeing used, the CH1 and CH2 menus will not be shown.MEASSet the number of significant digits, mV display option and concentrationunits displayed when in the measure mode:• Set the number of significant digits displayed measure mode• Scroll through 2, 3 or 4 significant digits• Default significant digits – 3• Enable mV values to be displayed on the second line• Scroll between On or OFF• Default mV setting – OFF• Set the displayed concentration units• Scroll through AUtO (automatically ranges from ppb to ppm), PPb(parts per billion, ppb), or PP (parts per million, ppm)• Default displayed concentration units – AUtOHOLDSet the time that the system will remain on hold before the actualmeasurements are displayed after a calibration:• Once the hold time expires, the system implements any programmedchanges to settings in the setup mode• After a calibration, the hold function allows the operator to rinse theelectrodes prior to recording actual measurement values• Default hold time – 30 minutesTADJAdjust the temperature reading from the ATC probe by ± 5.0 °C:• Default adjustment – 0.0 degrees CThermo Scientific Orion 2110XP Ammonia Analyzer User GuideIII-7
Page 1 and 2: Thermo ScientificOrion 2110XPAmmoni
Page 3: Table of ContentsChapter IGeneral I
Page 6 and 7: General InformationFeatures and Ben
Page 8 and 9: General InformationThe sensing elec
Page 10 and 11: General InformationOffline Calibrat
Page 12 and 13: General InformationGlossaryRefer to
Page 14 and 15: General InformationTwo Channel Anal
Page 16 and 17: Analyzer PreparationMounting andPlu
Page 18 and 19: Analyzer PreparationElectrical Wiri
Page 20 and 21: Analyzer PreparationWiring the Anal
Page 22 and 23: Analyzer PreparationTerminalAssignm
Page 24 and 25: Analyzer PreparationInstallation of
Page 26 and 27: Analyzer PreparationInstallation of
Page 28 and 29: Analyzer Preparation8. Invert the e
Page 30 and 31: Analyzer OperationDescription ofKey
Page 32 and 33: Analyzer OperationUsing PasswordPro
Page 36 and 37: Analyzer OperationALRMSet up to thr
Page 38 and 39: Analyzer OperationDefault Operator
Page 44 and 45: Analyzer OperationWarning: The rese
Page 46 and 47: Analyzer OperationNote: The followi
Page 64 and 65: Analyzer OperationStart-Up1. Replac
Page 66 and 67: CalibrationFlow Cell OperationThe s
Page 68 and 69: CalibrationAir RegulationThe Thermo
Page 70 and 71: CalibrationPerforming aDKA Calibrat
Page 72 and 73: CalibrationStep Operator Action Scr
Page 74 and 75: CalibrationCalibrationAbort StepsTh
Page 76 and 77: CalibrationError Operator Action Sc
Page 78 and 79: CalibrationSpan CheckProcedureThe T
Page 80 and 81: CalibrationStep Operator Action Scr
Page 82 and 83: Analyzer MaintenanceMonthly Mainten
Page 84 and 85:
Analyzer MaintenanceReplacement of
Page 86 and 87:
Analyzer MaintenanceReplacement ofR
Page 88 and 89:
TroubleshootingCalibration Log• D
Page 90 and 91:
TroubleshootingMeasurement Log• D
Page 92 and 93:
TroubleshootingElectronics Serial N
Page 94 and 95:
TroubleshootingKeypad Test• The m
Page 96 and 97:
TroubleshootingHigh SlopeSlope grea
Page 98 and 99:
TroubleshootingMalfunction Possible
Page 100 and 101:
TroubleshootingError/Event CodesErr
Page 102 and 103:
TroubleshootingDisplayedEvent CodeD
Page 104 and 105:
TroubleshootingHard ResetA hard res
Page 106 and 107:
TroubleshootingAdvanced Replacement
Page 108 and 109:
Customer ServiceDeclaration ofConfo
Page 110 and 111:
Customer ServiceHazardous Materials
Page 112 and 113:
AppendixMounting DimensionsORION 21
Page 114 and 115:
AppendixSpecificationsAmmonia Measu
Page 116 and 117:
AppendixOutputsNumber of Analog Out
Page 118 and 119:
AppendixOrdering InformationCat. No
Page 120 and 121:
AppendixField Replaceable PartsCat.
Page 122 and 123:
AppendixPipet OperationTip Ejection
Page 125:
Process Water InstrumentsNorth Amer
show all

Thermo Scientific Orion 2110XP Ammonia Analyzer

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?