MPX Series Video Encoders Front Panel - Teleste

More documents

Recommendations

Info

Changing Contact closure output state by motion detection sensorIn this case encoder changes CC output state (open/close) when motion isdetected by MD1 (motion detection 1) sensor. In this example you arecontrolling CC (contact closure) output which does not affect video stream.Select “0: Pass all frames” or “1: Pass I-frames” option1. Click “Connection” menu under the Configuration/Video/Edit VideoEncoding Settings page and select “0: Pass all frames or PassI-frames” option from the Filtering (Normal/Triggered) pull-down menu.Select “SNMP” option2. Go to the --> Confi guration/Contact Closure/Edit Contact ClosureSettings page, and set CC Output Mode to the “Group” and then select“SNMP” option from the Connection Type pull-down menu.Select “CCOUTPUT 1” optionSelect “CCOUTPUT 1” optionSelect “1: Pass all frames” or “1:Level sensitive trigger high” option3. Go to the --> Confi guration/Motion Detection/Edit Motion Detection andAction Settings page, and set Source to the “MD1”, select “CC OUTPUT1” option from the Target pull-down menu and select “1: Level sensitivetrigger high” option from the Action pull-down menu.Uploading JPEG files by contact closure input sensorIn this case encoder starts to upload JPEG files when CC input state is closed.Active checkbox must not be not selected!1. Go to the --> Confi guration/Pictures/Edit Picture Upload Settings pageand make sure that Active checkbox is not selected.Select “CC INPUT 1” optionSelect “JPEG 1” optionSelect “1: Level sensitivetrigger high” option2. Go to the --> Confi guration/Motion Detection/Edit Motion Detection andAction Settings page, and set Source to the “CC INPUT1”, select “JPEG1” option from the Target pull-down menu and select “1: Level sensitivetrigger high” option from the Action pull-down menu.68 MPX series video encoders user manual
Copyright acknowledgementsInformation in this document is subject to change without notice and does notrepresent a commitment on the part of Teleste Corporation.Copyright © Teleste Corporation. All Rights Reserved.No part of this document may be reproduced, transmitted, stored in a retrievalsystem, or translated into any other language without the express permissionof Teleste Corporation.Teleste CorporationVideo NetworksP.O. Box 323FIN-20101 TurkuFINLANDwww.teleste.comWEEE directiveDirective 2002/96/EC of the European Parliament and of the Council on wasteelectrical and electronic equipment (WEEE) obliges that producers appropriatelymark electrical and electronic equipment with the symbol indicating separatecollection. This obligation applies to the equipment put on the market in EU after13 August 2005.Teleste devices which belong to the scope of the directive have been markedwith the separate collection symbol shown below. The marking is according tothe standard EN 50419. The symbol indicates that the device has to be collectedand treated separately from unsorted municipal waste.User manual revision history note:The latest version is always available in pdf-format on our web site:www.teleste.comMPX series video encoders user manual 69
Page 3:
MPX Series Video Encoders Introduct
Page 6 and 7:
TLMPX Series Video Encoders Front P
Page 8 and 9:
InstallationQuick instructions12345
Page 10 and 11:
RS422 is a balanced data format. Si
Page 12 and 13:
Audio connection (MPC/MPX two/four
Page 14 and 15:
Ethernet connectionsEthernet connec
Page 16 and 17:
Video streamingVideo 1MPUMPC-E1 con
Page 18 and 19:
How to change the settingsGeneralTh
Page 20 and 21: StartingTo create a WebUI session t
Page 22 and 23: When monitoring an area for securit
Page 24 and 25: Painted area is chosen for watching
Page 26 and 27: QP (QuantizationParameter) 1 to 31.
Page 28 and 29: VIDEO ENCODING SETTINGS - MODIFYAdd
Page 30 and 31: VIDEO ENCODING SETTINGS - MODIFYVer
Page 32 and 33: Link To SDP fi le (Session Descript
Page 34 and 35: Video standard:Primary Server Direc
Page 36 and 37: PICTURE UPLOAD SETTINGS - MODIFYVer
Page 38 and 39: Input:Name:Status:Algorithm:Sensiti
Page 40 and 41: As an example:-Threshold: 30%-Filte
Page 42 and 43: Name:Status:Connection Type:IP addr
Page 44 and 45: CONTACT CLOSURE SETTINGSClick “Co
Page 46 and 47: SAP Service:Multicast TTL:Announcem
Page 48 and 49: RTSP Service:Current bandwidth:Maxi
Page 50 and 51: Video Standard:Join Multicast Group
Page 52 and 53: NETWORKClick “Network” menu und
Page 54 and 55: The address for default Gateway can
Page 56 and 57: SERVICESClick “Services” menu u
Page 58 and 59: USER MANAGEMENTClick “User manage
Page 60 and 61: Connection methods - Serial connect
Page 62 and 63: Detailed descriptions of CLI comman
Page 64 and 65: Ping commandUse the ping command to
Page 66 and 67: Eraseconf commandThe default factor
Page 68 and 69: 2. Select ActionSelect trigger and
Page 72: www.teleste.com
show all

MPX Series Video Encoders Front Panel - Teleste

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?