XNX Universal Transmitter - Merkantile

RRXNX Universal Transmitter6.2.1 XNX LabelsUL Certification LabelsAn explanation of the information on the XNX certification label is shown below.XNX Unit Serial NumberProduct NameXNX Unit Part NumberMinimum Voltage Requirement(16 for EC/mV and 18 for IR)Wattage RequirementXNXUNIVERSALTRANSMITTERWARNING: • TO REDUCE THE RISK OF IGNITION OF HAZARDOUS ATMOSPHERE CONDUIT RUNS MUST HAVE A SEAL FITTING CONNECTED WITHIN 18" [457mm] OF ENCLOSURE.CAUTION: • FOR SAFETY REASONS THIS EQUIPMENT MUST BE OPERATED AND SERVICED BY QUALIFIED PERSONNEL ONLY. READ AND UNDERSTAND MANUAL PRIOR TOSERVICING. • HIGH OFF SCALE READING MAY INDICATE EXPLOSIVE CONCENTRATIONS.• THIS AREA MUST BE FREE OF FLAMMABLE GASES DURING CALIBRATION.AVERTISSEMENT: • POUR REDUIRE LE RISQUE D' ALLUMAGE DANS L'ATMOSPHÈRE. LES CONDUITS DOIVENT AVOIR UN JOINT D'ÉTANCHÉITÉ INSTALLÉS À MOINS DEATTENTION: 18 " [457 mm] DU BOITIER.• POUR DES RAISONS DE SECURITÉ, CET EQUIPMENT DOIT ETRE UTILISÉ, ENTRETENU ET REPARÉ UNIQUEMENT PAR UN PERSONNEL QUALIFIÉ SEULEMENT.LIRE ET COMPRENDRE LE MANUEL D'INSTRUCTIONS AVANT UTILISATION.• DES LECTURES HORS ECHELLE PEUVENT INDIQUER DES CONCENTRATIONS EXPLOSIVES• CETTE ZONE DOIT ETRE EXEMPTE DE GAZ INFLAMMABLES PENDANT L'ETALONNAGEProduct NameUser Warnings/CautionsAdditional Agency Approval(configuration dependantSee XNX Certificationsby Part Number Series)XNX- SN: to 32 VDC Max. Class 2 Supply Req'dXNX Universal Transmitter for use in Class I, Div. 1 Groups B,C & DClass 1, Zone 1, Groups IIB+H2 Haz Loc. Tamb °C to °C Temp Code T4Only as to Explosion, Fire, Electrical and Shock HazardWhen Installed Per XNX ManualRelay Option XNX - UT -R or XNX-RLYContact Ratings: 250 VAC 5A, 24VDC 5A Resistive Loads Only35YLMfg'd by: Honeywell Analytics, Inc., 405 Barclay Blvd. Lincolnshire, IL 60069 USAUL ApprovalsFigure 6-1. XNX Label for Non-IS ApplicationsXNX Unit Serial NumberXNX Unit Part NumberCLASSIFIEDManufacturers Name and AddressXNXUNIVERSALTRANSMITTERMinimum Voltage Requirement(16 for EC/mV and 18 for IR)Wattage RequirementXNXUNIVERSALTRANSMITTERWARNING: • TO REDUCE THE RISK OF IGNITION OF HAZARDOUS ATMOSPHERE CONDUIT RUNS MUST HAVE A SEAL FITTING CONNECTED WITHIN 18" [457mm] OF ENCLOSURECAUTION: • SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY.• FOR SAFETY REASONS THIS EQUIPMENT MUST BE OPERATED AND SERVICED BY QUALIFIED PERSONNEL ONLY. READ AND UNDERSTAND MANUAL PRIOR TO SERVICING• HIGH OFF SCALE READING MAY INDICATE EXPLOSIVE CONCENTRATIONS.• THIS AREA MUST BE FREE OF FLAMMABLE GASES DURING CALIBRATION.AVERTISSEMENT: • POUR REDUIRE LE RISQUE D' ALLUMAGE DANS L'ATMOSPHÈRE. LES CONDUITS DOIVENT AVOIR UN JOINT D'ÉTANCHÉITÉ INSTALLÉS À MOINS DE 18 " [457 mm] DU BOITIERATTENTION: • LA SUBSTITUTION DES COMPOSANTES PEUT COMPROMETTRE LA SÉCURITÉ INTRINSÉQUÉ.• POUR DES RAISONS DE SECURITÉ, CET EQUIPMENT DOIT ETRE UTILISÉ, ENTRETENU ET REPARÉ UNIQUEMENT PAR UN PERSONNELQUALIFIÉ SEULEMENT LIRE ET COMPRENDRE LE MANUEL D'INSTRUCTIONS AVANT UTILISATION • DES LECTURES HORS ECHELLE PEUVENT INDIQUER DESCONCENTRATIONS EXPLOSIVES • CETTE ZONE DOIT ETRE EXEMPTE DE GAZ INFLAMMABLES PENDANT L'ETALONNAGEXNX- SN: to 32 VDC Max. Class 2 Supply Req'dXNX Universal Transmitter for use in Class I, Div. 1 Groups B,C & D [Exia]Class 1, Zone 1, Groups IIB+H2 Haz Loc. Tamb °C to °C Temp Code T4Only as to Explosion, Fire, Electrical Shock Hazard and Intrinsic SafetyAssociated Apparatus Providing Intrinsically Safe Circuits When Installed PerXNX Manual and Control Drawing 1226E0402 Um=250VRelay Option XNX - UT -R or XNX-RLYContact Ratings: 250 VAC 5A, 24VDC 5A Resistive Loads Only35YLMfg'd by: Honeywell Analytics, Inc., 405 Barclay Blvd. Lincolnshire, IL 60069 USACLASSIFIEDXNXUNIVERSALTRANSMITTERUser Warnings/CautionsAdditional Agency Approval(configuration dependantSee XNX Certificationsby Part Number Series)UL ApprovalsFigure 6-2. XNX Label for IS ApplicationsManufacturers Name and AddressSection 6 - Specifications 6-146.2.1 XNX Labels