Positron G-Series User Manual (PDF)

More documents

Recommendations

Info

Positron Telecommunication Systems Inc. – G-Series Gateways User GuideSystem -> 3G MenuA cellular 3G voice and data network can be used to provide a failover connection to theInternet. In the event that the G-Series Gateway detects that the normal wired Internetconnection is no longer working, it can use the cellular network for voice and dataconnection until the wired network connection is restored.Enable:Enables the 3G device, which is typically a USB `thumb drive`typeunit plugged into one of the available USB ports on theGateway.Default: not enabled54VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
Positron Telecommunication Systems Inc. – G-Series Gateways User GuideVoice and Data:Enables data to be sent through the G-Series Gateway in additionto voice.Default: not enabledTelephone Line Failover:When selected, 3G will be used as a failover in the event of failureof the telephone line.Default: not enabledEthernet Failover:When selected, 3G will be used as a failover for the Ethernet link.Default: not enabledIP Address 1, Port 1, IP Address 2, Port 2:These are the IP addresses of popular Internet services andGateway device ports used to verify the 3G connection. If theGateway does not get a response for packets sent through thespecified address and ports, it will be considered a fail and thesystem will be unable to connect/reconnect.Defaults:IP Address 1: 198.133.219.25Port 1: 80IP Address 2: 216.255.83.40Port 2: 80Provider:Drop-down box listing preconfigured 3G providers. Selecting theappropriate provider name from the list will automatically configurethe next three fields. In the event that the 3G provider is not in thelist, the settings can be tried as a starting point.Default: standardDCE-DTE Options, Packet Data Protocol, Dial Number:If the specific model cannot be found in the Provider drop downbox above, then the information for these three fields should berequested from the 3G provider. However, the default values inthe fields may prove to be correct.Defaults: values have been set.Probe Response Timeout:Time in seconds. If there is no response within the time specifiedfrom a packet sent as a probe, then a failure is declared.Default: 5Probe Interval:Number of seconds between probes from the Gateway system.Default: 1055VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
Page 6 and 7: Positron Telecommunication Systems
Page 104 and 105:
Positron Telecommunication Systems
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
show all

Positron G-Series User Manual (PDF)

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?