MOTOX -N - RELKO

MOTOX ® -N
Overview:
Paint system Color tone
Standard: RAL 5015
Typical area
of use
Plastic
(Standard)
2K-PUR
(extra charge)
2K-Epoxy
(extra charge)
on demand:
RAL 1007, 1012,
1023, 2000, 2004,
3000, 5007, 5009,
5010, 5012, 6011,
7001, 7011, 7030,
7032, 7035, 9005,
9006, black-dull,
others on request
Standard: RAL 7031
on demand:
RAL1003, 1018,
2004, 5002, 5015,
6011, 7000, 9010,
9011, 9016,
others on request
Standard: RAL 7035
on demand:
RAL 5015, 6018,
7031,
others on request
Primed (RAL 7032)
Unpainted -
Standard 1-layer
coat of lacquer for
the internal area
Standard 2-layer
coat of lacquer
especially for
installation in the
open or in case of
increased
demands on
corrosion
protection
High-quality coat of
lacquer for the
external area or in
case of attack by
diluted acid and
alkaline solution
(≤5%)
For overpainting:
adhesive agent for
all common paint
systems,
temporary corrosion
protection
For overpainting:
(adhesive agent)
temporary
corrosion
protection
Coats of paint
For protection of the drives against corrosion and all kinds of
ambient influences, we offer three high quality painting
systems in several color tones.
All coats of paint are applied carefully by spray painting in the
most modern painting plants.
Other color tones and special paintings are possible on request.
Overpaintability * Chem. phys.
resistance
With plastic lacquer or
synthetic resin
lacquer
After preceeding
grinding with:
2K-PUR lacquer
2K-Epoxy lacquer
After preceeding
grinding with:
2K-PUR lacquer
2K-Epoxy lacquer
2K-AC lacquer
Excellent with:
plastic lacquer, synthetic
resin lacquer,
2K-PUR lacquer,
2K-Epoxy lacquer, SH
lacquer, 2K-AC lacquer
Excellent with:
plastic lacquer,
synthetic resin lacquer,
oil paint, bitumenous
paint, 2K-PUR paint
2K-Epoxy paint
Good resistance to
cleaning agents, oil
and benzine,
resistant to short-
time attack by diluted
acid and alkaline solution
(≤3%), not
resistant to solvent
not resitant to watervaour
Excellent
resistance to
weak acid and
alkaline
solution (≤3%),
oil, grease, benzine,
cooling emulsion,
salt, solvent; tough
and scratch-resistant-coating
film
Excellent resistance
to weak acid and alkaline
solution (≤5%),
oil, grease, benzine,
cooling emulsion,
salt, solvent; tough
and scratch-resistant-coating
film
Good resistance to
cleaning agent, to
salt spraying and
resistant to oil and
benzine
Temperature
resistance
-40°C to 100°C
up to 140°C for
a short time
-40°C to 150°C
-40°C to 150°C
-40°C to 150°C
- (-40°C to 150°C)
Remarks
Standard coat of
lacquer with
excellent adhesive
characteristics,
not suitable for
storage in the open;
not suitable for
installation in the
open air
Standard coat of
lacquer for cooling
tower and agitator
drive or if sea
water resistance
below deck or
similar is required
2K-Epoxy lacquer
“chalks” in case of
installation in the
open (does not
effect the quality),
high gloss with
good mechanical
resistance
Adhesive agent
with excellent
adhesive
characteristics and
good corrosion
protection
Components from
grey cast iron dip-primed,
components
from steel primed or
galvanised, components
from Al and plastic
untreated
* Note:
The information for varnishing (over-coating) do not represent
a release in the sense of a warranty for the quality of the coating
material delivered by your supply.
For the quality and compatibility only to the varnish manufactures
is responsible.
1 - 3