Installation and Configuration Guide for Linux® Workstations

More documents

Recommendations

Info

Connect video components Video hardware connection The only video hardware you must provide are a sync generator, VTR, HD/SDI-ready broadcast monitor and patch panel (if desired). 1 Connect the output of the sync generator to the top Ref Loop port of the AJA K3G-Box. 2 Connect the Input port of the NVIDIA SDI card (the one next to the DVI port) to the bottom Ref Loop port of the AJA K3G-Box. 3 Connect the Fill (outer) port of the NVIDIA SDI card to the Input port of the AJA HD5DA distribution amplifier. 4 Connect one of the OUT ports of the distribution amplifier to an SDI IN port of the broadcast monitor. 5 For RTD or Stereo, connect another OUT port of the amplifier to the Link A input port of the VTR. 6 For Stereo or RTD, connect the Key (middle) SDI port of the NVIDIA SDI card to the Link B input port of the RTD VTR. 7 Connect the RS-422 port of the AJA K3G-Box to the VTR control port. 8 If not using RTD, connect SDI OUT A, SDI OUT B, SDI IN A and SDI IN B ports of the VTR to the SDI1, SDI2, SDI3 and SDI4 ports on the front of the AJA K3G-Box. 9 Connect the SDI IN 1/A, SDI IN 2/B, SDI OUT 1/A and SDI OUT 2/B plugs of the AJA cable to the SDI1, SDI2, SDI3 and SDI4 ports of the AJA Kona 3G card. 10 Connect the SDI IN 1/A, SDI IN 2/B, SDI OUT 1/A and SDI OUT 2/B plugs on the other end of the AJA cable to the SDI1, SDI2, SDI3 and SDI4 ports on the back of the AJA K3G-Box, as illustrated. 11 Connect the AJA control cable to the AJA Kona card and to the corresponding port on the back of the AJA K3G-Box. Connect audio components Your application uses the Discreet Native Audio subsystem. Discreet Native Audio uses the following hardware components, shipped with your system. 10 | Chapter 3 Hardware configuration
Lucid ADA 88192 Audio Converter Converts signals between the workstation and all digital or analog audio I/O devices. AJA K3G-Box Balanced Audio breakout box and AJA Kona 3G adapter card The Balanced Audio breakout box is the audio component of the AJA breakout box. It provides connections for audio I/O. This breakout box connects to the AJA Kona 3G adapter on your workstation. The Kona 3G adapter provides real-time input and output of uncompressed SD and HD video signals as well as audio data at 24-bit resolution. The Kona 3G adapter handles balanced AES/EBU audio signals from the Balanced Audio breakout box. Connect the Discreet Native Audio hardware components to the AJA breakout box Connect audio components | 11
Page 1 and 2: ® Autodesk ® Flame Premium 2013 A
Page 3 and 4: Contents Chapter 1 Installation wor
Page 5 and 6: Installation workflows This guide c
Page 7 and 8: System requirements Hardware requir
Page 9 and 10: Hardware configuration 3 If you are
Page 11 and 12: There are two kinds of Lustre works
Page 13: Peripheral connections overview Ada
Page 17 and 18: The storage can be connected to the
Page 19 and 20: Connect media storage | 15
Page 21 and 22: ■ The total number of enlcosures
Page 23 and 24: NOTE The XR 5402 and XR 5412 RAID e
Page 25 and 26: While Autodesk Media and Entertainm
Page 27 and 28: Install Linux To prepare your syste
Page 29 and 30: etc/sysconfig/network-scripts/ifcfg
Page 31 and 32: This can be done with version 1.5 o
Page 33 and 34: 2 Create the LUNs. 3 Power off the
Page 35 and 36: 4 Repeat for each disk. To partitio
Page 37 and 38: meta-data=/dev/vg00/lvol1 agcount=1
Page 39 and 40: Installing Your Software Prepare th
Page 41: ■ To use the new configuration fi
Page 44 and 45: ■ On the mounted filesystem creat
Page 46 and 47: 2 Use the 2007, 2008, 2009, 2010, o
Page 48 and 49: 2 Activate the new network share fo
Page 50 and 51: Burn for Lustre This is the Linux r
Page 52 and 53: 2 Insert the first installation dis
Page 54 and 55: Configure backburner server to dete
Page 56 and 57: Port All computers on the BrowseD n
Page 58 and 59: This function receives the followin
Page 60 and 61: Attribute dst_host dst_path Attribu
Page 62 and 63: Attribute src_path dst_os dst_path
Page 64 and 65:
■ Separate your media and metadat
Page 66 and 67:
Reserving Bandwidth for an Applicat
Page 68 and 69:
Perform the steps in the procedure
Page 70 and 71:
By default, the configuration file
Page 72 and 73:
NOTE If you are using XFS and unwri
Page 74 and 75:
Verifying that Stone and Wire Proce
Page 76 and 77:
2 Depending on the result of the pr
Page 78 and 79:
6 If you continue to get error mess
Page 80 and 81:
Option: MB/sec: 111.509057 Ping suc
Page 82 and 83:
As root, open a terminal on your wo
Page 84 and 85:
Network licensing 3 Select Node-Loc
Page 86 and 87:
2 Log in to support portal: https:/
Page 88 and 89:
Change the default port used by the
Page 90 and 91:
Type: -v -H -V -i -r --red-frames T
Page 93 and 94:
Index A AMD starting daemon 77 appl
Page 95 and 96:
NFS 39 starting daemon 77 O operati
show all

Installation and Configuration Guide for Linux® Workstations

Create successful ePaper yourself

Delete template?

Save as template?