WSCAD51 Getting Started - FTP Directory Listing

More documents

Recommendations

Info

<strong>Getting</strong> <strong>Started</strong> Replace the 'Function text' input line with '!MPCB Worm' (it means a worm drive) and position it again below the circuit breaker. Method 2: The contacts are placed first and the coil is assigned to the contacts later (virtual contactor) Now draw the main circuit for motors M1 and M2. For this you need three 3-pole main contacts, which you will find via 'Schematic - Load symbol ...' under 'NO_3pol_power'. Position the first contact at 90.0 / 130.0 mm. 48
Design capture Create an new reference name in the Contactor list an insert a function text for the contacts. 49
Page 1:
WSCAD51 Getting Started
Page 4 and 5: Table Of Contents General..........
Page 7 and 8: Introduction General With WSCAD 5 y
Page 9: WebHelp supports you with just the
Page 12 and 13: Getting Started Black Box - Desti
Page 14 and 15: Getting Started UFD-management with
Page 17 and 18: Working with WSCAD 5 Restrictions o
Page 19 and 20: WSCAD 5.1 Demo Working with WSCAD 5
Page 21 and 22: Enter for example an 'A' as first v
Page 23 and 24: Function keys Working with WSCAD 5
Page 25: Configuring the screen layout Worki
Page 28 and 29: Getting Started Setting up a projec
Page 30 and 31: Getting Started The project 'WSCAD
Page 32 and 33: Getting Started Hint 26 You will al
Page 34 and 35: Getting Started Adjusting the pract
Page 36 and 37: Getting Started Page configuration
Page 38 and 39: Getting Started To load a component
Page 40 and 41: Getting Started Placing symbols wit
Page 42 and 43: Getting Started Select '1LA7083-6AA
Page 44 and 45: Getting Started Now place another m
Page 46 and 47: Getting Started The automatic funct
Page 48 and 49: Getting Started Close the Terminal
Page 50 and 51: Getting Started Hint 44 Circuit dia
Page 52 and 53: Getting Started Select New and you'
Page 56 and 57: Getting Started Make no changes in
Page 58 and 59: Getting Started Connecting coils an
Page 60 and 61: Getting Started Contactor Manager A
Page 62 and 63: Getting Started After selecting mak
Page 64 and 65: Getting Started After OK button the
Page 66 and 67: Getting Started Full automatic Cont
Page 68 and 69: Getting Started Position the cursor
Page 70 and 71: Getting Started Loading the individ
Page 72 and 73: Getting Started Modifying the PLC b
Page 74 and 75: Getting Started The symbols of dest
Page 76 and 77: Getting Started Inserting corners T
Page 78 and 79: Getting Started Inserting potential
Page 80 and 81: Getting Started Enter 'P11' as the
Page 82 and 83: Getting Started Finally, go back to
Page 84 and 85: Getting Started Click 'New' to load
Page 86 and 87: Getting Started As you see, the cab
Page 89 and 90: Automatic functions General WSCAD 5
Page 91 and 92: Automatic functions paths) of the c
Page 93 and 94: Automatic functions Set the File ty
Page 95 and 96: Exit the dialog with 'OK'. Automati
Page 97 and 98: Hint The data is in mm and refers t
Page 99 and 100: Automatic functions Now we need a '
Page 101 and 102: Automatic functions Note the format
Page 103 and 104: Hint Please ensure that the option
Page 105:
Automatic functions Repeat this pro
Page 108 and 109:
Getting Started If you want to modi
Page 110 and 111:
Getting Started The Full project au
Page 112 and 113:
Getting Started If 'By Co-ordinates
Page 114 and 115:
Getting Started Accept the settings
Page 116 and 117:
Getting Started Select the required
Page 118 and 119:
Getting Started Now you are going t
Page 121 and 122:
WSCAD Services In conclusion ... In
Page 123:
Epilog WSCAD electronic GmbH was fo
show all

WSCAD51 Getting Started - FTP Directory Listing

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?