WSCAD51 Getting Started - FTP Directory Listing

More documents

Recommendations

Info

<strong>Getting</strong> <strong>Started</strong> Contactor Manager Assigning contactors to a specific manufacturer is done with the Contactor Manager. Once the manufacturer's name has been assigned, the contact comb is generated and the cross-references are created automatically. At this stage, the contactors used in the circuit diagram have no manufacturer’s reference. To open the Contactor Manager select in the menu, 'Automatic funct. – Contactor Manager - Contactor Manager'. You can of course enlarge the window if needed. 54
Design capture You see all reference names (coil) and their contacts. If you select a contact you get informations on the right side about them. If you set the option View / function text you see the function texts also in the tree. Mark all coils (-Q..) 55
Page 1:
WSCAD51 Getting Started
Page 4 and 5:
Table Of Contents General..........
Page 7 and 8:
Introduction General With WSCAD 5 y
Page 9: WebHelp supports you with just the
Page 12 and 13: Getting Started Black Box - Desti
Page 14 and 15: Getting Started UFD-management with
Page 17 and 18: Working with WSCAD 5 Restrictions o
Page 19 and 20: WSCAD 5.1 Demo Working with WSCAD 5
Page 21 and 22: Enter for example an 'A' as first v
Page 23 and 24: Function keys Working with WSCAD 5
Page 25: Configuring the screen layout Worki
Page 28 and 29: Getting Started Setting up a projec
Page 30 and 31: Getting Started The project 'WSCAD
Page 32 and 33: Getting Started Hint 26 You will al
Page 34 and 35: Getting Started Adjusting the pract
Page 36 and 37: Getting Started Page configuration
Page 38 and 39: Getting Started To load a component
Page 40 and 41: Getting Started Placing symbols wit
Page 42 and 43: Getting Started Select '1LA7083-6AA
Page 44 and 45: Getting Started Now place another m
Page 46 and 47: Getting Started The automatic funct
Page 48 and 49: Getting Started Close the Terminal
Page 50 and 51: Getting Started Hint 44 Circuit dia
Page 52 and 53: Getting Started Select New and you'
Page 54 and 55: Getting Started Replace the 'Functi
Page 56 and 57: Getting Started Make no changes in
Page 58 and 59: Getting Started Connecting coils an
Page 62 and 63: Getting Started After selecting mak
Page 64 and 65: Getting Started After OK button the
Page 66 and 67: Getting Started Full automatic Cont
Page 68 and 69: Getting Started Position the cursor
Page 70 and 71: Getting Started Loading the individ
Page 72 and 73: Getting Started Modifying the PLC b
Page 74 and 75: Getting Started The symbols of dest
Page 76 and 77: Getting Started Inserting corners T
Page 78 and 79: Getting Started Inserting potential
Page 80 and 81: Getting Started Enter 'P11' as the
Page 82 and 83: Getting Started Finally, go back to
Page 84 and 85: Getting Started Click 'New' to load
Page 86 and 87: Getting Started As you see, the cab
Page 89 and 90: Automatic functions General WSCAD 5
Page 91 and 92: Automatic functions paths) of the c
Page 93 and 94: Automatic functions Set the File ty
Page 95 and 96: Exit the dialog with 'OK'. Automati
Page 97 and 98: Hint The data is in mm and refers t
Page 99 and 100: Automatic functions Now we need a '
Page 101 and 102: Automatic functions Note the format
Page 103 and 104: Hint Please ensure that the option
Page 105: Automatic functions Repeat this pro
Page 108 and 109: Getting Started If you want to modi
Page 110 and 111:
Getting Started The Full project au
Page 112 and 113:
Getting Started If 'By Co-ordinates
Page 114 and 115:
Getting Started Accept the settings
Page 116 and 117:
Getting Started Select the required
Page 118 and 119:
Getting Started Now you are going t
Page 121 and 122:
WSCAD Services In conclusion ... In
Page 123:
Epilog WSCAD electronic GmbH was fo
show all

WSCAD51 Getting Started - FTP Directory Listing

Create successful ePaper yourself

Delete template?

Save as template?