The IBM eServer BladeCenter JS20 - IBM Redbooks

More documents

Recommendations

Info

7.3 Adding machine information With the resources added, add information regarding the machine on which you want to perform a base operating system (BOS) installation. 1. From the main NIM menu (Figure 7-10), select Add a new Machine to the Network Installation Management environment. Figure 7-10 Adding new machine information to NIM 130 The IBM Eserver BladeCenter JS20
2. In the Add New Machine window (Figure 7-11), enter the host name of the server that you want to add to the NIM environment from this window. Figure 7-11 Host name of new machine Tip: The NIM server must be able to resolve the host name of the new server. Ensure that this host name can be resolved by DNS or a hosts file. Chapter 7. Installing AIX on the JS20 131
Page 1:
The IBM Eserver BladeCenter JS20 Le
Page 4 and 5:
Note: Before using this information
Page 6 and 7:
Chapter 4. Planning considerations
Page 8 and 9:
vi The IBM Eserver BladeCenter JS20
Page 10 and 11:
6-8 Language selection . . . . . .
Page 12 and 13:
x The IBM Eserver BladeCenter JS20
Page 14 and 15:
Trademarks The following terms are
Page 16 and 17:
worked actively with Linux adoption
Page 18 and 19:
xvi The IBM Eserver BladeCenter JS2
Page 20 and 21:
2 The IBM Eserver BladeCenter JS20
Page 22 and 23:
for e-commerce and On Demand Busine
Page 24 and 25:
Page 26 and 27:
2.1 Overview of the BladeCenter inf
Page 28 and 29:
Attention: Nonredundant power is no
Page 30 and 31:
Attention: Power supply modules mus
Page 32 and 33:
Figure 2-4 KVM Management Module Th
Page 34 and 35:
2.1.4 I/O modules You use the keybo
Page 36 and 37:
Note: The IBM 4-Port Gb Ethernet Sw
Page 38 and 39:
The Brocade Enterprise SAN Module c
Page 40 and 41:
2.2 BladeCenter JS20 The BladeCente
Page 42 and 43:
2.2.1 Base features There are two m
Page 44 and 45:
You can learn more about the availa
Page 46 and 47:
Expansion cards You can install any
Page 48 and 49:
2.3.1 Review of POWER and PowerPC A
Page 50 and 51:
In 1993, IBM announced the POWER2 p
Page 52 and 53:
These components all interact with
Page 54 and 55:
IBM processors implementing PowerPC
Page 56 and 57:
PowerPC 970 and PowerPC 970FX proce
Page 58 and 59:
capabilities were usually referred
Page 60 and 61:
For additional information about th
Page 62 and 63:
The major features of the PowerPC 9
Page 64 and 65:
the bus interface is slightly lower
Page 66 and 67:
3.1 Operating system support 3.1.1
Page 68 and 69:
3.2.2 IBM Director management, the
Page 70 and 71:
Page 72 and 73:
4.1 Network planning Successful ins
Page 74 and 75:
Hardware management subnet We recom
Page 76 and 77:
Application subnet The primary reas
Page 78 and 79:
4.2 Operating system installation T
Page 80 and 81:
When you perform network installati
Page 82 and 83:
IBM Director Agent for the BladeCen
Page 84 and 85:
Network considerations and summary
Page 86 and 87:
Page 88 and 89:
5.1 Management Module configuration
Page 90 and 91:
PASSW0RD. The 0 in the password is
Page 92 and 93:
When a new LAN Switch I/O Module is
Page 94 and 95:
At this point, the LAN Switch I/O M
Page 96 and 97:
5.3.2 Setting the boot sequence Set
Page 98 and 99: Figure 5-7 Viewing firmware levels
Page 100 and 101: 4. After you download all the PKT f
Page 102 and 103: 5.4.3 BladeCenter JS20 firmware (BI
Page 104 and 105: 1. Download the firmware update pac
Page 106 and 107: LAN Switch Module in I/O Module Bay
Page 108 and 109: e. Leave the values for User Define
Page 110 and 111: connections. This is sufficient to
Page 112 and 113: minutes, you are disconnected. You
Page 114 and 115: 6. As soon as you type 8, the Open
Page 116 and 117: 5. Select the JS20 blade that you a
Page 118 and 119: 100 The IBM Eserver BladeCenter JS2
Page 120 and 121: 6.1 Installing Linux Both Red Hat E
Page 122 and 123: SuSE sources SuSE installations are
Page 124 and 125: 3. In the next panel as shown in Fi
Page 126 and 127: To build your own zImage.initrd, fo
Page 128 and 129: 6.2.1 BOOTP DHCP is an extension to
Page 130 and 131: 6.3.1 Red Hat Kickstart Red Hat pro
Page 132 and 133: 6.3.2 SuSE AutoYaST SLES provides a
Page 134 and 135: ► System Set the general system i
Page 136 and 137: The syntax for mkzimage_cmdline is
Page 138 and 139: 3. We select the install option and
Page 140 and 141: 122 The IBM Eserver BladeCenter JS2
Page 142 and 143: 7.1 Minimal NIM installation Follow
Page 144 and 145: 4. In the next window (Figure 7-4),
Page 146 and 147: 3. In the Configure NIM Environment
Page 150 and 151: 3. In the next window (Figure 7-12)
Page 152 and 153: 7.4 Preparing the NIM master With a
Page 154 and 155: 1. On the first panel, select the d
Page 156 and 157: 4. As illustrated in Figure 7-19, w
Page 158 and 159: 8.1 IBM Director IBM Director is a
Page 160 and 161: 8.1.1 Setting up an IBM Director Se
Page 162 and 163: 8. Enter the database connection in
Page 164 and 165: 2. With the sources copied to the h
Page 166 and 167: As CSM was being developed, the Ext
Page 168 and 169: This is the interface that will be
Page 170 and 171: version packaged with CSM. And you
Page 172 and 173: You can verify what user IDs you co
Page 174 and 175: ► PowerMethod: Should always be b
Page 176 and 177: The csmsetupyast command uses an XM
Page 178 and 179: RHEL Red Hat Enterprise Linux RISC
Page 180 and 181: Online resources ► CSM for Linux:
Page 182 and 183: How to get IBM Redbooks Help from I
Page 184 and 185: eth0 62 eth1 62 F Fibre Channel Exp
Page 186 and 187: T translation lookaside buffer (TLB
Page 190: The IBM Eserver BladeCenter JS20 Le
show all

The IBM eServer BladeCenter JS20 - IBM Redbooks

Create successful ePaper yourself

Delete template?

Save as template?