The IBM eServer BladeCenter JS20 - IBM Redbooks

More documents

Recommendations

Info

52 The IBM Eserver BladeCenter JS20
Chapter 4. Planning considerations 4 This chapter discusses planning considerations associated with the implementation of the IBM Eserver BladeCenter JS20. Specifically it covers network planning, operating system installation, and systems management. © Copyright IBM Corp. 2005. All rights reserved. 53
Page 1:
The IBM Eserver BladeCenter JS20 Le
Page 4 and 5:
Note: Before using this information
Page 6 and 7:
Chapter 4. Planning considerations
Page 8 and 9:
vi The IBM Eserver BladeCenter JS20
Page 10 and 11:
6-8 Language selection . . . . . .
Page 12 and 13:
x The IBM Eserver BladeCenter JS20
Page 14 and 15:
Trademarks The following terms are
Page 16 and 17:
worked actively with Linux adoption
Page 18 and 19:
xvi The IBM Eserver BladeCenter JS2
Page 20 and 21: 2 The IBM Eserver BladeCenter JS20
Page 22 and 23: for e-commerce and On Demand Busine
Page 26 and 27: 2.1 Overview of the BladeCenter inf
Page 28 and 29: Attention: Nonredundant power is no
Page 30 and 31: Attention: Power supply modules mus
Page 32 and 33: Figure 2-4 KVM Management Module Th
Page 34 and 35: 2.1.4 I/O modules You use the keybo
Page 36 and 37: Note: The IBM 4-Port Gb Ethernet Sw
Page 38 and 39: The Brocade Enterprise SAN Module c
Page 40 and 41: 2.2 BladeCenter JS20 The BladeCente
Page 42 and 43: 2.2.1 Base features There are two m
Page 44 and 45: You can learn more about the availa
Page 46 and 47: Expansion cards You can install any
Page 48 and 49: 2.3.1 Review of POWER and PowerPC A
Page 50 and 51: In 1993, IBM announced the POWER2 p
Page 52 and 53: These components all interact with
Page 54 and 55: IBM processors implementing PowerPC
Page 56 and 57: PowerPC 970 and PowerPC 970FX proce
Page 58 and 59: capabilities were usually referred
Page 60 and 61: For additional information about th
Page 62 and 63: The major features of the PowerPC 9
Page 64 and 65: the bus interface is slightly lower
Page 66 and 67: 3.1 Operating system support 3.1.1
Page 68 and 69: 3.2.2 IBM Director management, the
Page 72 and 73: 4.1 Network planning Successful ins
Page 74 and 75: Hardware management subnet We recom
Page 76 and 77: Application subnet The primary reas
Page 78 and 79: 4.2 Operating system installation T
Page 80 and 81: When you perform network installati
Page 82 and 83: IBM Director Agent for the BladeCen
Page 84 and 85: Network considerations and summary
Page 88 and 89: 5.1 Management Module configuration
Page 90 and 91: PASSW0RD. The 0 in the password is
Page 92 and 93: When a new LAN Switch I/O Module is
Page 94 and 95: At this point, the LAN Switch I/O M
Page 96 and 97: 5.3.2 Setting the boot sequence Set
Page 98 and 99: Figure 5-7 Viewing firmware levels
Page 100 and 101: 4. After you download all the PKT f
Page 102 and 103: 5.4.3 BladeCenter JS20 firmware (BI
Page 104 and 105: 1. Download the firmware update pac
Page 106 and 107: LAN Switch Module in I/O Module Bay
Page 108 and 109: e. Leave the values for User Define
Page 110 and 111: connections. This is sufficient to
Page 112 and 113: minutes, you are disconnected. You
Page 114 and 115: 6. As soon as you type 8, the Open
Page 116 and 117: 5. Select the JS20 blade that you a
Page 120 and 121:
6.1 Installing Linux Both Red Hat E
Page 122 and 123:
SuSE sources SuSE installations are
Page 124 and 125:
3. In the next panel as shown in Fi
Page 126 and 127:
To build your own zImage.initrd, fo
Page 128 and 129:
6.2.1 BOOTP DHCP is an extension to
Page 130 and 131:
6.3.1 Red Hat Kickstart Red Hat pro
Page 132 and 133:
6.3.2 SuSE AutoYaST SLES provides a
Page 134 and 135:
► System Set the general system i
Page 136 and 137:
The syntax for mkzimage_cmdline is
Page 138 and 139:
3. We select the install option and
Page 140 and 141:
122 The IBM Eserver BladeCenter JS2
Page 142 and 143:
7.1 Minimal NIM installation Follow
Page 144 and 145:
4. In the next window (Figure 7-4),
Page 146 and 147:
3. In the Configure NIM Environment
Page 148 and 149:
7.3 Adding machine information With
Page 150 and 151:
3. In the next window (Figure 7-12)
Page 152 and 153:
7.4 Preparing the NIM master With a
Page 154 and 155:
1. On the first panel, select the d
Page 156 and 157:
4. As illustrated in Figure 7-19, w
Page 158 and 159:
8.1 IBM Director IBM Director is a
Page 160 and 161:
8.1.1 Setting up an IBM Director Se
Page 162 and 163:
8. Enter the database connection in
Page 164 and 165:
2. With the sources copied to the h
Page 166 and 167:
As CSM was being developed, the Ext
Page 168 and 169:
This is the interface that will be
Page 170 and 171:
version packaged with CSM. And you
Page 172 and 173:
You can verify what user IDs you co
Page 174 and 175:
► PowerMethod: Should always be b
Page 176 and 177:
The csmsetupyast command uses an XM
Page 178 and 179:
RHEL Red Hat Enterprise Linux RISC
Page 180 and 181:
Online resources ► CSM for Linux:
Page 182 and 183:
How to get IBM Redbooks Help from I
Page 184 and 185:
eth0 62 eth1 62 F Fibre Channel Exp
Page 186 and 187:
T translation lookaside buffer (TLB
Page 190:
The IBM Eserver BladeCenter JS20 Le
show all

The IBM eServer BladeCenter JS20 - IBM Redbooks

Create successful ePaper yourself

Delete template?

Save as template?