- Page 1:
The IBM Eserver BladeCenter JS20 Le
- Page 4 and 5:
Note: Before using this information
- Page 6 and 7:
Chapter 4. Planning considerations
- Page 8 and 9:
vi The IBM Eserver BladeCenter JS20
- Page 10 and 11:
6-8 Language selection . . . . . .
- Page 12 and 13:
x The IBM Eserver BladeCenter JS20
- Page 14 and 15:
Trademarks The following terms are
- Page 16 and 17:
worked actively with Linux adoption
- Page 18 and 19:
xvi The IBM Eserver BladeCenter JS2
- Page 20 and 21:
2 The IBM Eserver BladeCenter JS20
- Page 22 and 23:
for e-commerce and On Demand Busine
- Page 24 and 25:
6 The IBM Eserver BladeCenter JS20
- Page 26 and 27:
2.1 Overview of the BladeCenter inf
- Page 28 and 29:
Attention: Nonredundant power is no
- Page 30 and 31:
Attention: Power supply modules mus
- Page 32 and 33:
Figure 2-4 KVM Management Module Th
- Page 34 and 35:
2.1.4 I/O modules You use the keybo
- Page 36 and 37:
Note: The IBM 4-Port Gb Ethernet Sw
- Page 38 and 39:
The Brocade Enterprise SAN Module c
- Page 40 and 41:
2.2 BladeCenter JS20 The BladeCente
- Page 42 and 43:
2.2.1 Base features There are two m
- Page 44 and 45:
You can learn more about the availa
- Page 46 and 47:
Expansion cards You can install any
- Page 48 and 49:
2.3.1 Review of POWER and PowerPC A
- Page 50 and 51:
In 1993, IBM announced the POWER2 p
- Page 52 and 53:
These components all interact with
- Page 54 and 55:
IBM processors implementing PowerPC
- Page 56 and 57:
PowerPC 970 and PowerPC 970FX proce
- Page 58 and 59:
capabilities were usually referred
- Page 60 and 61:
For additional information about th
- Page 62 and 63:
The major features of the PowerPC 9
- Page 64 and 65:
the bus interface is slightly lower
- Page 66 and 67:
3.1 Operating system support 3.1.1
- Page 68 and 69:
3.2.2 IBM Director management, the
- Page 70 and 71:
52 The IBM Eserver BladeCenter JS20
- Page 72 and 73:
4.1 Network planning Successful ins
- Page 74 and 75:
Hardware management subnet We recom
- Page 76 and 77:
Application subnet The primary reas
- Page 78 and 79:
4.2 Operating system installation T
- Page 80 and 81:
When you perform network installati
- Page 82 and 83:
IBM Director Agent for the BladeCen
- Page 84 and 85:
Network considerations and summary
- Page 86 and 87:
68 The IBM Eserver BladeCenter JS20
- Page 88 and 89:
5.1 Management Module configuration
- Page 90 and 91:
PASSW0RD. The 0 in the password is
- Page 92 and 93:
When a new LAN Switch I/O Module is
- Page 94 and 95:
At this point, the LAN Switch I/O M
- Page 96 and 97:
5.3.2 Setting the boot sequence Set
- Page 98 and 99:
Figure 5-7 Viewing firmware levels
- Page 100 and 101:
4. After you download all the PKT f
- Page 102 and 103:
5.4.3 BladeCenter JS20 firmware (BI
- Page 104 and 105:
1. Download the firmware update pac
- Page 106 and 107:
LAN Switch Module in I/O Module Bay
- Page 108 and 109:
e. Leave the values for User Define
- Page 110 and 111:
connections. This is sufficient to
- Page 112 and 113:
minutes, you are disconnected. You
- Page 114 and 115:
6. As soon as you type 8, the Open
- Page 116 and 117:
5. Select the JS20 blade that you a
- Page 118 and 119:
100 The IBM Eserver BladeCenter JS2
- Page 120 and 121:
6.1 Installing Linux Both Red Hat E
- Page 122 and 123:
SuSE sources SuSE installations are
- Page 124 and 125:
3. In the next panel as shown in Fi
- Page 126 and 127:
To build your own zImage.initrd, fo
- Page 128 and 129: 6.2.1 BOOTP DHCP is an extension to
- Page 130 and 131: 6.3.1 Red Hat Kickstart Red Hat pro
- Page 132 and 133: 6.3.2 SuSE AutoYaST SLES provides a
- Page 134 and 135: ► System Set the general system i
- Page 136 and 137: The syntax for mkzimage_cmdline is
- Page 138 and 139: 3. We select the install option and
- Page 140 and 141: 122 The IBM Eserver BladeCenter JS2
- Page 142 and 143: 7.1 Minimal NIM installation Follow
- Page 144 and 145: 4. In the next window (Figure 7-4),
- Page 146 and 147: 3. In the Configure NIM Environment
- Page 148 and 149: 7.3 Adding machine information With
- Page 150 and 151: 3. In the next window (Figure 7-12)
- Page 152 and 153: 7.4 Preparing the NIM master With a
- Page 154 and 155: 1. On the first panel, select the d
- Page 156 and 157: 4. As illustrated in Figure 7-19, w
- Page 158 and 159: 8.1 IBM Director IBM Director is a
- Page 160 and 161: 8.1.1 Setting up an IBM Director Se
- Page 162 and 163: 8. Enter the database connection in
- Page 164 and 165: 2. With the sources copied to the h
- Page 166 and 167: As CSM was being developed, the Ext
- Page 168 and 169: This is the interface that will be
- Page 170 and 171: version packaged with CSM. And you
- Page 172 and 173: You can verify what user IDs you co
- Page 174 and 175: ► PowerMethod: Should always be b
- Page 176 and 177: The csmsetupyast command uses an XM
- Page 180 and 181: Online resources ► CSM for Linux:
- Page 182 and 183: How to get IBM Redbooks Help from I
- Page 184 and 185: eth0 62 eth1 62 F Fibre Channel Exp
- Page 186 and 187: T translation lookaside buffer (TLB
- Page 190: The IBM Eserver BladeCenter JS20 Le