Tender Documents - Oil India Limited

More documents

Recommendations

Info

Twin drum draw works having main drum lebus grooved for 1” or 1.1/8” drilling line and 9.1/16” sand line drum. Hydromatic Brake: Water-cooled Hydromatic brake, driven by a twin-disc clutch with independent oil bath chain case to serve as assist brake, with suitable capacity water tank, valves and piping installed on the carrier. Disc brake [shaft mounted] in lieu of hydromatic shall also be acceptable. TWIN STOP DEVICE (CROWN & FLOOR SAVER): One (1) pneumatically activated Twin-stop Device – Crown Saver to prevent collision between traveling block assembly and the crown block assembly, Floor Saver to prevent collision between the traveling block assembly and the drill floor. (b) DRILLER’S CONSOLE: Driller‟s console, adjustable height, located at the rear of the carrier incorporating all functions to carry out workover operations smoothly. Additionally, following minimum instruments should be mounted in suitable enclosure at Driller‟s console arranged in such a manner to give clear view of each & every gauge to Driller while operating the draw-works. Weight Indicator, Martin Decker or equivalent make with suitable sensator. Should be complete with 6 lines & 8 lines dials for 1” or 1.1/8”. [Calibration certificate shall be provided] Mud pressure gauges 0-10,000 PSI or 0-6,000 PSI. The mud pressure gauge system should have one (1) gauge for standpipe and one (1) for annulus pressure Suitable recorder for recording hook load SPM indicator for mud pump at driller‟s console NOTE: Rig instrumentation should be suitable for Hazardous area as per OMR-1984. (c) MAST: Two-section Telescoping Mast manufactured & monogrammed per API Spec 4F, with hydraulic mast tilting & extending systems and automatic locking device to lock the mast into its fully extended operating position. Crown block assembly should be complete with sheaves for cat-line, sand-line, sheave units for rig tongs, power tong/pipe spinner. Clear height (below crown) from the ground: Min. 102 ft, Max. 112 ft. Static hook load capacity: Min. 250,000 lbs with 8 lines strung Wind load resistance with full set back: Minimum 80 mph (128 kmph) with guy lines Minimum 150 Ton (136 Tonnes) capacity Crown Block Assembly with adequate no. of sheaves for stringing up 8 lines Mast load & wind guy lines
Sheaves for catline, sandline, sheave units for rig tongs, power tong / pipe spinner (d) (e) (f) (g) (h) (i) (j) SUB-STRUCTURE: Substructure assembly with provisions for mounting 17.1/2” or 20.1/2” Rotary Table, manufactured & monogrammed per API Spec 4F. Floor height adjustable from 10 ft to 19 ft or fixed at 14 ft height. Minimum clear height under Rotary beams: 7 ft ( When adjusted at 10 ft height) Static Rotary Capacity: 125 tons (250000 lbs) Minimum Pipe Setback Capacity 70 tons (140000 lbs) Minimum Combined Static Rotary & Setback Capacity: 390000 lbs Minimum Work Floor Dimensions: 15 ft. x 15 ft. approximately. Substructure should have provision for rat hole and mouse hole TRAVELLING BLOCK AND HOOK: Unitized traveling block & hook assembly with 4 sheaves having rated capacity between 125 tons to 187 tons (113 MT to 170 MT). ROTARY DRIVE: Rotary drive, for driving 17.1/2” or 20.1/2” Rotary Table by means of suitable air flex clutch drive from the rotary counter shaft, with oil bath chain guard and sprocket for rotary table. The static load rating of 250000 lbs complete with master bushing SERVICE WINCH: Hydraulic winch with wire line, tail chain, control valve & hoses installed having bare drum line pull capacity of minimum 5000 lbs. HYDRAULIC SYSTEM: Suitable for heavy duty power tubing tong, raising & lowering the mast, and hydraulic winch. May be single or double, hydraulic pumps of suitable capacity, completed with necessary hydraulic circuit and accessories. The system should be capable of operating properly the Telescopic Rams of the Rig for rigging up or down the mast, the hydraulic motor to operate the winch and hydraulic subs. Preferably, the hydraulic pumps should be driven by the PTOs fitted with the Transmission. ROTARY TABLE: Rotary Table with 17.1/2” or 20.1/2” opening and static load rating of minimum 250 tons ROTARY SWIVEL: Swivel having dead load rating between 150 ton to 200 ton (136 MT to 181 MT) with 5000 PSI working pressure and complete with bail bumper support, goose neck connection to rotary hose etc. Swivel pin connection should be 3.1/2” or 4.1/2” API regular left hand with matching cross-over.
Page 1 and 2: Oil India Limited CONTRACTS DEPARTM
Page 3 and 4: Head-Contracts, Oil India Ltd., P.O
Page 5 and 6: 7.0 OIL now looks forward to your a
Page 7 and 8: 4.0 AMENDMENT OF BID DOCUMENTS: 4.1
Page 9 and 10: i) Any Nationalised / scheduled Ban
Page 11 and 12: other accompanying documents except
Page 13 and 14: 19.0 MODIFICATION AND WITHDRAWAL OF
Page 15 and 16: 22.2 The Priced bids of the unsucce
Page 17 and 18: of requisite value, as per Indian S
Page 19 and 20: No request will be considered for c
Page 21 and 22: 1.2 The horsepower rating of the ri
Page 23 and 24: 7.0 DOCUMENTS: Bidders must furnish
Page 25 and 26: 2.0 To ascertain the substantial re
Page 27 and 28: NOTE: The above items are defined i
Page 29 and 30: SECTION - I GENERAL CONDITIONS OF C
Page 31 and 32: such personnel with personnel accep
Page 33 and 34: 9.0 INSURANCE: 9.1 The Contractor s
Page 35 and 36: 12.0 TERMINATION: 12.1 TERMINATION
Page 37 and 38: of the services and by the rules &
Page 39 and 40: equipment and/or loss or damage to
Page 41 and 42: herein, shall be limited to Company
Page 43 and 44: 29.0 SUBSEQUENTLY ENACTED LAWS: Sub
Page 45: (a) Minimum width of the well site
Page 49 and 50: Draw Works. The Transmission should
Page 51 and 52: (v) (vi) (vii) Approximate transpor
Page 53 and 54: ) OTHER ITEMS: i) Skid Mounted Well
Page 55 and 56: (d) (e) Junk subs 1. One (1) no. su
Page 57 and 58: 7.14 ADDITIONAL ITEMS: The followin
Page 59 and 60: including their recommended dosage
Page 61 and 62: 5) Any additional requirement of cr
Page 63 and 64: 5. Proper insulation mat should be
Page 65 and 66: v) One ambulance with dedicated dri
Page 67 and 68: Sl. No. Key Personnel Number per lo
Page 69 and 70: Duties & responsibilities include s
Page 71 and 72: manpower deployed by the Contractor
Page 73 and 74: 1.13 “Facility” means and inclu
Page 75 and 76: 3.4 Contractor’s Personnel: Contr
Page 77 and 78: such as Mines safety rules etc. Con
Page 79 and 80: c) WELL COMPLETION/WELL ABANDONMENT
Page 81 and 82: In case, no demobilization charges
Page 83 and 84: of this contract and shall indemnif
Page 85 and 86: shall furnish an Undertaking simila
Page 87 and 88: e) Contractor fails to meet any of
Page 89 and 90: interests, the Company shall notify
Page 91 and 92: d. The contractor shall provide a c
Page 93 and 94: submit comprehensive HSE manual & p
Page 95 and 96: tools under Clause No. 7.8 of Secti
Page 97 and 98:
. Payment towards force majeure day
Page 99 and 100:
The Standby day rate will be payabl
Page 101 and 102:
Section 2 - Commitments of the Bidd
Page 103 and 104:
Section 6 - Equal treatment of all
Page 105 and 106:
APPENDIX - 1 Date : ________ WORK-O
Page 107 and 108:
trailer mounted / Ext propelled. ii
Page 109 and 110:
Make : Model: Capacity in MT: 4.6 S
Page 111 and 112:
Sl. No. I T E M At Expense of Suppl
Page 113 and 114:
Sl. No. I T E M At Expense of Suppl
Page 115 and 116:
ANNEXURE-II PROFORMA FOR BIO DATA O
Page 117 and 118:
ANNEXURE - IV Details of all cables
Page 119 and 120:
PROFORMA-A LIST OF ITEMS (Equipment
Page 121 and 122:
4 Standby Charge Day 365 d.4 D.4= d
Page 123 and 124:
PROFORMA-D STATEMENT OF NON-COMPLIA
Page 125 and 126:
PROFORMA - F FORM OF PERFORMANCE BA
Page 127 and 128:
3. In consideration of the payments
Page 129:
AUTHORISATION FOR ATTENDING BID OPE
show all

Tender Documents - Oil India Limited

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?