VL2000 ug finalcomp.book - Kodak

More documents

Recommendations

Info

Setting Up Page Correlation Setting Up the Controller Activity lation mark is printed. Usually the location should be 1 /8 inch or further down the page. e. In the Height field, enter the size of each segment of the page correlation mark. This value can be 1 /8 to 1 /4 inch wide. f. In the Distance field, enter the distance of the sensors from the cue A sensor. (This distance is best determined with “Setting the Cue Delays” on page 255.) g. With the Sensor polarity buttons, select or deselect the proper sensor polarity. Leaving the boxes unchecked (normal polarity) is more common. Note: If necessary, determine the proper polarity by checking the indicators on Tools Connections. Thye indicator is black when the sensor detects a mark (white when not detecting a mark). h. Select Apply. 9. At the system controller, select Transport and a printhead that prints black ink. 10. Use the Page correlation area and the substeps that follow to configure the printhead. a. In the Mark position field, enter the location from the GS edge of the printed document where the page correlation mark is printed. Usually the location should be 1 /8 inch or further from the left edge of the printhead, but the value is allowed to be 0.0 to the printhead’s printing width. b. In the Mark width field, enter the size of the page correlation mark. English - metric equivalents 1 /16 inch 0.061 inch 0.159 cm 1 /8 inch 0.125 inch 0.318 cm 1 /4 inch 0.250 inch 0.635 cm print width 18.67 inch 47.41 cm Usually this value is at least 1 /8 inch, and usually 1 /4 inch wide. The mark can be as narrow as 1 /16 inch and as wide as the printhead. Sizes at the extremes of the range may cause excessive page correlation errors due to substrate wandering underneath the sensors. c. With the Sensor buttons, select the sensor that will detect the marks printed by this printhead. d. Select Not used if the page correlation marks can be ignored for this printhead and others in line with it. e. Select Apply. 154 KODAK VERSAMARK <strong>VL2000</strong> Printing System Z:\systemcontrollers\library\text.fdr\og 023e proc1 vl2-vt3000 og.fm
Setting Up Page Correlation Setting Up the Controller Activity 11. Repeat step 9 for each printhead that prints black, then go to step 12. 12. If the printheads are to print correlation marks, start the job and print documents until a correlation mark should be detected by each used sensor. 13. Use “Positioning the Page Correlation Sensors” on page 156 for each correlation sensor. Operator’s Guide 155 Z:\systemcontrollers\library\text.fdr\og 023e proc1 vl2-vt3000 og.fm
Page 1:
VERSAMARK VL2000 Printing System VL
Page 4 and 5:
FCC Compliance Statement This equip
Page 6 and 7:
Scope Text Notations This manual us
Page 9 and 10:
Contents Changes in this Version ..
Page 11 and 12:
Contents Monitoring Operations.....
Page 13 and 14:
Figures Figure 1 VL2000 modules....
Page 15 and 16:
Contents Figures Figure 101 Line ho
Page 17 and 18:
Chapter 1. Operator Controls The KO
Page 19 and 20:
The System Controller and Its Windo
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Displaying Print Station Informatio
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Related Software IJ Data Prep Relat
Page 39 and 40:
Related Software IJPDS Proofer IJPD
Page 41 and 42:
Print Stations Print Stations The p
Page 43 and 44:
Unwind Unit Unwind Unit The unwind
Page 45 and 46:
Unwind Unit Figure 8 Unwind unit, p
Page 47 and 48:
Unwind Unit A blue light around the
Page 49 and 50:
Unwind Unit Drag bar A stationary b
Page 51 and 52:
Print Tower Controls Web Guide Modu
Page 53 and 54:
Print Tower Controls Print Tower Co
Page 55 and 56:
Print Tower Controls Web cleaner bo
Page 57 and 58:
Print Tower Controls Outfeed Module
Page 59 and 60:
Rewind Unit Rewind Unit The rewind
Page 61 and 62:
Rewind Unit External Power and Air
Page 63 and 64:
Rewind Unit External Power and Air
Page 65 and 66:
Chapter 2. Basic Operations Every o
Page 67 and 68:
Operations Overview System Setup Pr
Page 69 and 70:
Operations Overview Printhead Opera
Page 71 and 72:
Operations Overview Printhead Opera
Page 73 and 74:
Preliminary Operations Turning the
Page 75 and 76:
Preliminary Operations Turning the
Page 77 and 78:
Starting the System Controller Stan
Page 79 and 80:
Operator Access to Controller Funct
Page 81 and 82:
Powering the Print Station Off Powe
Page 83 and 84:
Turning the Printing System Off Fig
Page 85 and 86:
Turning the Printing System Off Fig
Page 87 and 88:
Raising and Lowering the Print Towe
Page 89 and 90:
Changing Paper Rolls at the Unwind
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Roll Position on the Shaft Figure 5
Page 97 and 98:
Changing Paper Rolls at the Rewind
Page 99 and 100:
Changing Paper Rolls at the Rewind
Page 101 and 102:
Webbing the Unwind Unit Figure 58 W
Page 103 and 104: Jogging the Web Jogging the Web 1.
Page 105 and 106: Adjusting the Gripper Rollers Adjus
Page 107 and 108: Center positioning Center positioni
Page 109 and 110: Webbing the Web Cleaner Figure 64 W
Page 111 and 112: Webbing the Dryer Webbing the Dryer
Page 113 and 114: Webbing the Dryer Figure 67 Dryer w
Page 115 and 116: Webbing the Turnbar Webbing the Tur
Page 117 and 118: Webbing the Rewind Unit Webbing the
Page 119 and 120: Webbing the Rewind Unit 6. Feed eno
Page 121 and 122: Selecting the Motor Direction Selec
Page 123 and 124: Tightening the Web Use this procedu
Page 125 and 126: Positioning the Cue Sensor Position
Page 127 and 128: Printhead Activities Moving a Print
Page 129 and 130: Enabling an Existing Printhead Enab
Page 131 and 132: Setting Up Cue Mark Printing Settin
Page 133 and 134: Job Setup Setting Up a Print Job 5.
Page 135 and 136: Job Setup Setting Up a Print Job 13
Page 137 and 138: Job Setup Setting Up a Print Job 23
Page 139 and 140: Adjusting the Data Registration (Y-
Page 141 and 142: Adjusting the Lateral Image Positio
Page 143 and 144: Adjusting the Duplexed Registration
Page 145 and 146: Printhead Registration Printhead Re
Page 147 and 148: Printhead Registration VL2000 test
Page 149 and 150: Printhead Registration Always adjus
Page 151 and 152: Setting Up Page Correlation Setting
Page 153: Setting Up Page Correlation Setting
Page 157 and 158: Saving the Job Settings Saving the
Page 159 and 160: Print Operations Displaying Printhe
Page 161 and 162: Readying Printheads to Print Readyi
Page 163 and 164: Monitoring Operations • Red circl
Page 165 and 166: Preventing Printhead Problems Preve
Page 167 and 168: Print Job Operations Aligning the L
Page 169 and 170: Print Job Operations Aligning the L
Page 171 and 172: Adjusting the Dryer Temperature Adj
Page 173 and 174: Start Up Procedure Start Up Procedu
Page 175 and 176: Reprinting Data ! DANGER Stay clear
Page 177 and 178: Running Jobs with Job Spooling Runn
Page 179 and 180: Running Jobs with Job Spooling The
Page 181 and 182: Selecting a New Printing Speed Sele
Page 183 and 184: Splicing the Web Figure 85 Tear the
Page 185 and 186: Splicing the Web DANGER Danger of c
Page 187 and 188: External Fluid Container Procedure
Page 189 and 190: Replacing the Replenisher or Cleane
Page 191 and 192: Disposing of Waste Fluid Disposal G
Page 193 and 194: Chapter 3. Advanced Operations Only
Page 195 and 196: Baseline System Numbering Baseline
Page 197 and 198: Multiple Print Tower Numbering If n
Page 199 and 200: Multiple Print Tower Numbering 9. S
Page 201 and 202: Defining Print Station INet Address
Page 203 and 204: Identifying Printheads Identifying
Page 205 and 206:
Identifying Printheads 4. Drag all
Page 207 and 208:
System Setup of Optional Functions
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Setting Up the Activities and Users
Page 219 and 220:
Setting Up the Activities and Users
Page 221 and 222:
Setting Up the Job for Production T
Page 223 and 224:
Logging In Logging In If the CS410
Page 225 and 226:
Logging Out Logging Out While opera
Page 227 and 228:
Changing a Stop Reason Changing a S
Page 229 and 230:
How Read and Print Works How Read a
Page 231 and 232:
Positioning the Reader Positioning
Page 233 and 234:
Setting Up the Job Queue and Print
Page 235 and 236:
Setting Up the Job Queue • Keep r
Page 237 and 238:
Setting Up the Job Queue or simplex
Page 239 and 240:
Setting Up the Job Queue Figure 99
Page 241 and 242:
Using an MPC Manual Setup Making De
Page 243 and 244:
Using an MPC Manual Setup Making De
Page 245 and 246:
Using an MPC Manual Setup Overridin
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Setting Up the Line Hole Sensor Fig
Page 253 and 254:
Adjusting the Cue Sensor Adjusting
Page 255 and 256:
Setting the Cue Delays Setting the
Page 257 and 258:
Setting the Cue Delays Field Value/
Page 259 and 260:
Setting the Cue Delays f. Enter inf
Page 261 and 262:
Calculating the Speed Comp Value 1.
Page 263 and 264:
Placing the Page Correlation Marks
Page 265 and 266:
Using Special Cueing Using Special
Page 267 and 268:
Implementing Special Cueing Impleme
Page 269 and 270:
Operational Modes Entering Key Oper
Page 271 and 272:
Operational Modes Exiting Key Opera
Page 273 and 274:
Retrieving Accounting Information V
Page 275 and 276:
Replace and Packing Removing the Pr
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Packing the Printhead Figure 113 Sh
Page 283 and 284:
Packing the Printhead Figure 117 Sh
Page 285 and 286:
Unpacking the Printhead Unpacking t
Page 287 and 288:
Unpacking the Printhead Figure 127
Page 289 and 290:
Installing the Printhead Figure 130
Page 291 and 292:
Installing the Printhead 16. Refer
Page 293 and 294:
Chapter 4. Maintenance In general,
Page 295 and 296:
Preventive Maintenance Table 3 Tran
Page 297 and 298:
Scheduled Operator Maintenance Proc
Page 299 and 300:
Scheduled Operator Maintenance Proc
Page 301 and 302:
Chapter 5. Troubleshooting The erro
Page 303 and 304:
Common Print Defects Action: Correc
Page 305 and 306:
Printing Problems Print Screen Stat
Page 307 and 308:
Glossary This appendix contains a g
Page 309 and 310:
Glossary cue sensor A sensor that d
Page 311 and 312:
Glossary 3. An architected host-to-
Page 313 and 314:
Glossary punch-perforation A proces
Page 315 and 316:
Glossary web break sensor A section
Page 317 and 318:
Index Emergency Stop button unwind
Page 319 and 320:
Index S Saving accounting informati
Page 322:
Eastman Kodak Company 3000 Research
show all

VL2000 ug finalcomp.book - Kodak

Create successful ePaper yourself

Delete template?

Save as template?