PDFï¼7.7MB

More documents

Recommendations

Info

TEN / EEN type Bore Type Components Description Applicable cutter TEN09R... Clamping screw Wrench Torx bit Grip Mono block type substitution wrench Replacement Parts Cat. No. *TEN09R... CSTR-4L100 BT15S BT15M H-TBS T-15D Standard cutting conditions Low carbon steels (C15E etc.) High carbon steels (C45, C55 etc.) Alloyed steels (42CrMo4, 17Cr3 etc.) Tool steels (X155CrVMo12 1 etc.) Stainless steels (X5CrNi18-9 etc.) Grey cast irons Work materials Ductile cast irons Aluminium alloys (Si < 13%) Aluminium alloys (Si 13%) Hardness Recommended Cutting speed Feed per tooth Selection criteria HB grade Vc (m/min) fz (mm/t) First choice AH725 100 - 250 Priority on impact resistance AH140 80 - 180 0.1 - 0.6 ~ 200 Priority on wear resistance T3130 120 - 250 Priority on surface quality NS740 100 - 250 0.1 - 0.5 First choice AH725 100 - 230 200 ~ 300 Priority on impact resistance AH140 80 - 180 0.1 - 0.5 Priority on wear resistance T3130 120 - 250 quality Priority on surface NS740 100 - 250 0.1 - 0.4 First choice AH725 100 - 230 150 ~ 300 Priority on impact resistance AH140 80 - 150 0.1 - 0.5 Priority on wear resistance T3130 120 - 250 Priority on surface quality NS740 100 - 250 0.1 - 0.4 First choice AH725 100 - 180 ~ 300 Priority on impact resistance AH140 80 - 120 0.1 - 0.5 Priority on wear resistance T3130 100 - 180 - First choice AH140 90 - 180 0.1 - 0.45 - First choice Priority on resistance AH120 140 - 250 wear T1115 150 - 280 0.1 - 0.6 - AH120 100 - 200 T1115 120 - 220 0.1 - 0.6 First choice Priority on wear resistance - First choice TH10 500 - 1500 0.1 - 0.5 9 TAC Mills Notes: · Remove excessive chip accumulation with an air blast. · When chips stick to the cutting edges (aluminium machining), use a water soluble coolant. · When cutting an interrupted surface or a casting skin, the feed (fz) should be reduced below the recommended value shown in the above table. · Cutting conditions are limited by machine power, workpiece rigidity, and spindle output. When the cutting width, depth or overhang length is large, set Vc and fz to the lower recommended values and check the machine power and vibration. Installation of the extra close pitch cutter inserts The extra close pitch cutter has a slanted screw. Locate insert and then fasten the screw. (Fig. A) Appropriate torque is 3.5 N·m. After fastening the screw, please ensure there is no space between the cutter body and insert. (Fig. B) Locate insert and then fasten the screw. Fig. A Fig. B Notes on use of wiper insert To achieve a good surface finish, a wiper insert is recommended. (PNCU0905GNER-W) When using the wiper insert, install the insert as shown in Fig. C. Ensure that the groove is at the front as shown in Fig. D. The wiper insert has two wiping corners. (Fig. D) Do not use the other corners. It may break the tool body. Fig. C Mark Cutting edge Fig. D Cutting edge Groove 9–41
TAN type Diameter ø63 ~ 315 mm 45° 4.7 mm 7.5 mm Steel Cast Iron Face Milling Screw on type (Octagonal insert) øDb ød a b R Rake angle: A.R. 6° R.R. +15.5° (Square insert) Lf1 Lf2 ˚ ˚ Max. ap: 4.7 mm øDc1 øD1-1 ap øDc2 øD1-2 ap Max. ap: 7.5 mm 9 TAC Mills Cat. No. No. of Dimensions (mm) Weight Stock Air Center Mounting Inserts details øDc1 øDc2 øD1-1 øD1-2 øDb ød r Lf1 Lf2 b a (kg) hole bolt TAN07R063M22.0E05 5 63 60.3 76 76.3 41 22 20 40 41.4 6.3 10.4 0.5 with CM10x30H 9-138A TAN07R080M27.0E06 6 80 77.3 93 93.3 50 27 22 50 51.4 7 12.4 1.0 with CM12x30H 9-138A TAN07R100M32.0E07 7 100 97.3 113 113.3 60 32 28.5 50 51.4 8 14.4 1.5 with TMBA-M16H 9-138B TAN07R125M40.0E08 8 125 122.3 138 138.3 71 40 29 63 64.4 9 16.4 2.5 with TMBA-M20H 9-138B TAN07R160M40.0E10 10 160 157.3 173 173.3 100 40 29 63 64.4 9 16.4 4.0 without - 9-138C TAN07R200M60.0E12 12 200 197.3 213 213.3 135 60 39 63 64.4 14 25.7 6.5 without - 9-138C NEW TAN07R250M60.0E15 15 250 247.3 263 263.3 130 60 39 63 64.4 14 25.7 9.0 without - 9-138C NEW TAN07R315M60.0E18 18 315 312.3 328 328.3 220 60 39 80 81.4 14 25.7 18.0 without - 9-138C TAN07R063M22.0E06 6 63 60.3 76 76.3 41 22 20 40 41.4 6.3 10.4 0.5 with CM10x30H 9-138A TAN07R080M27.0E08 8 80 77.3 93 93.3 50 27 22 50 51.4 7 12.4 1.0 with CM12x30H 9-138A TAN07R100M32.0E10 10 100 97.3 113 113.3 60 32 28.5 50 51.4 8 14.4 1.5 with TMBA-M16H 9-138B TAN07R125M40.0E12 12 125 122.3 138 138.3 71 40 29 63 64.4 9 16.4 2.5 with TMBA-M20H 9-138B TAN07R160M40.0E15 15 160 157.3 173 173.3 100 40 29 63 64.4 9 16.4 4.0 without - 9-138C TAN07R200M60.0E18 18 200 197.3 213 213.3 135 60 39 63 64.4 14 25.7 6.5 without - 9-138C NEW TAN07R250M60.0E21 21 250 247.3 263 263.3 130 60 39 63 64.4 14 25.7 9.0 without - 9-138C NEW TAN07R315M60.0E24 24 315 312.3 328 328.3 220 60 39 80 81.4 14 25.7 18.0 without - 9-138C Pitch Coarse Close Wedge type (Octagonal insert) øDb ød a b R Rake angle: A.R. 6° R.R. +15.5° (Square insert) Lf1 Lf2 ˚ ˚ Max. ap: 4.7 mm øDc1 øD1-1 ap øDc2 øD1-2 ap Max. ap: 7.5 mm Pitch Extra close 9–42 Cat. No. No. of Dimensions (mm) Weight Stock Air Mounting Inserts øDc1 øDc2 øDc1- øDc1- (kg) 1 2 øDb ød r Lf1 Lf2 b a hole details TAN07R063M22.0E08W 8 63 60.3 76 76.3 41 22 20 40 41.4 6.3 10.4 0.6 without 9-138B TAN07R080M27.0E10W 10 80 77.3 93 93.3 50 27 25 50 51.4 7 12.4 1.1 without 9-138B TAN07R100M32.0E14W 14 100 97.3 113 113.3 60 32 28.5 50 51.4 8 14.4 1.6 without 9-138B TAN07R125M40.0E18W 18 125 122.3 138 138.3 71 40 29 63 64.4 9 16.4 2.5 without 9-138B TAN07R160M40.0E22W 22 160 157.3 173 173.3 100 40 29 63 64.4 9 16.4 3.6 without 9-138C TAN07R200M60.0E28W 28 200 197.3 213 213.3 135 60 39 63 64.4 14 25.7 5.8 without 9-138C Replacement parts Screw on type Description Applicable cutter TAN07R... Cat. No. *TAN07R... Clamping screw Torx bit CSPE-5L150 BLD IP20/S7 BLD IP20/M7 Grip H-TB H-TB Mono block type substitution wrench IP-20T Wrench Technical Reference (15-1) Wedge type Description Applicable cutter Clamping screw Wedge Torx bit Grip Wrench : Stocked items. Cat. No. TAN07R...W DS-6P CL ARM-10-TUNG1 BLD IP15/S7 H-TBS
Page 1 and 2: R Lf ap 6.4mm Chapter Composition o
Page 3 and 4: Designation System for TAC Mills TA
Page 5 and 6: Designation System for TAC Milling
Page 7 and 8: Selection Guide for TAC mills Face
Page 13 and 14: Selection Guide for TAC mills Squar
Page 15 and 16: Selection Guide for TAC mills Squar
Page 17 and 18: Selection Guide for TAC mills Selec
Page 19 and 20: TUNGALOY Selection 9 TAC Mills Char
Page 21 and 22: Basic Selection for TAC Mills Face
Page 23 and 24: Basic Selection for TAC Mills Face
Page 25 and 26: Basic Selection for TAC Mills Shoul
Page 27 and 28: Basic Selection for TAC Mills Shoul
Page 29 and 30: Basic Selection for TAC Mills High
Page 31 and 32: Basic Selection for TAC Mills Die E
Page 33 and 34: TAC Mill Overview Bore types Face M
Page 35 and 36: TAC Mill Overview Bore types Should
Page 37 and 38: TAC Mill Overview Shank types Face
Page 39 and 40: TAC Mill Overview Shank types High
Page 41: TEN / EEN type Diameter ø32 ~ 160
Page 45 and 46: T/EAW13 Diameter ø50 ~ 160 mm 45°
Page 47 and 48: T/EAW13 9 TAC Mills Standard cuttin
Page 49 and 50: Lightning Mills TME4400 /B Face Mil
Page 51 and 52: 15˚ 15˚ TAC Mills for large depth
Page 53 and 54: TAC Mills TGP4100RBAE Standard cutt
Page 55 and 56: All PCD-tipped TAC Mills for high f
Page 57 and 58: TPQ / EPQ type JIS Diameter ø25 ~
Page 59 and 60: TPO / EPO07 Diameter ø12 ~ 50mm St
Page 61 and 62: TPS / EPS11 Diameter ø12~63 mm Ste
Page 63 and 64: TPS / EPS11 Replacement Parts TPS /
Page 65 and 66: TPO / EPO18 Diameter ø25~160 mm St
Page 67 and 68: Machining modes Shoulder milling Sl
Page 69 and 70: TPM / EPM type Roughing type øDb
Page 71 and 72: TPD / EPD type Diameter ø12 ~ 40 m
Page 73 and 74: 1.4 1.4 TPW13 Diameter ø50 ~ 125 m
Page 75 and 76: 9 TAC Mills EPH Shoulder Milling Ca
Page 77 and 78: EPH Standard cutting conditions Sh
Page 79 and 80: EVH Diameter ø10 ~ 16 mm 90° ~ 4.
Page 81 and 82: All PCD-tipped TAC Mills for high f
Page 83 and 84: TAC Mills for large depth of cut TP
Page 85 and 86: TAC Mills TSE3000R(IA)E Face Millin
Page 87 and 88: TAC Mills TSE4000RIAE Face Milling
Page 89 and 90: Top-Feed Mills, AD TPS/EPS17 Should
Page 91 and 92: Top-Feed Mills, AD TPS/EPS17 Machin
Page 93 and 94:
15°17° 1 mm ø16 ~ 80 mm Air Hole
Page 95 and 96:
Standard cutting conditions Work ma
Page 97 and 98:
Standard cutting conditions Work ma
Page 99 and 100:
TXQ12R ø50~125 mm 2 mm Steel Stain
Page 101 and 102:
EXH Diameter ø10 ~ 16 mm 20° 0.6,
Page 103 and 104:
T/EXP Diameter ø20 ~ 125 mm 10°,
Page 105 and 106:
T/EXP Inserts 05 type General inser
Page 107 and 108:
T/EXP Diameter ø20 ~ 160 mm 10°,
Page 109 and 110:
TRC / ERC type Inserts For general
Page 111 and 112:
TAC Flash radius mills TRD12 • 16
Page 113 and 114:
TAC radius mills T/ERF6000 Diameter
Page 115 and 116:
TAC Flash endmills with center cutt
Page 117 and 118:
TAC Flash Endmills ESD10 Shoulder M
Page 119 and 120:
TAC Flash ball endmills EBP R Radiu
Page 121 and 122:
TAC ball Endmills TBN1000 Pocketing
Page 123 and 124:
TAC Flash Mills for plunging TZP12
Page 125 and 126:
TAC Flash Mills for plunging TZF11
Page 127 and 128:
“T-Bar” Modular System TMS Diam
Page 129 and 130:
TAC Flasah chamfering mills ECC31 G
Page 131 and 132:
TAC Mills for super finishing SFP40
Page 133 and 134:
All PCBN-tipped TAC Mills for high
Page 135 and 136:
ASN / TSN ø100 ~ 250 mm Steel Stai
Page 137 and 138:
ASN / TSN Replacement parts Work ma
Page 139 and 140:
Mounting Details for TAC Mills Cutt
Page 141 and 142:
TAC Milling Inserts Inserts ADMT08P
Page 143 and 144:
TAC Milling Inserts AST11T3PDR-MJ/M
Page 145 and 146:
TAC Milling Inserts LMEUZNEN-MJ Sha
Page 147 and 148:
TAC Milling Inserts ONUAN-ML/MJ/W S
Page 149 and 150:
TAC Milling Inserts SCMT08-23 Shape
Page 151 and 152:
TAC Milling Inserts SEN1203AG, SEKR
Page 153 and 154:
TAC Milling Inserts SPHA431FNW, SPH
Page 155 and 156:
TAC Milling Inserts SW13T3AFR- Shap
Page 157 and 158:
TAC Milling Inserts TEN43Z, TECN43Z
Page 159 and 160:
TAC Milling Inserts XCET310404ER St
Page 161 and 162:
TAC Milling Inserts XVGTEC-MJ, XVG
Page 163 and 164:
TAC Milling Inserts ZDAT/FN Shape C
show all

PDFï¼7.7MB

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

PDFï¼7.7MB